• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.14 no.5
• /
• pp.549-560
• /
• 1989

In this paper, the method of determining the initial weighting vlaues fuctioning as a filter under the Directional Constrained Minimization of Power(DCMP) algorithm is presented. By analyzing the sideband beamformer with the Finite Impulse Response (FIR) filter concepts, the constraints of any desired directions are obtained and the initial weighing values with fast adaptation time are formulated from those constraints. By applying this proposed initial weighting values to the DCMP and the spatial averaging processor, the interference of a desired direction and the coherent noises are eliminated at the same time. The improvement of this method compared with the existing algorithm is confirmed by computer simulation.

• International Journal of Aeronautical and Space Sciences
• /
• v.15 no.3
• /
• pp.219-231
• /
• 2014

We develop a preliminary design optimization procedure in this paper regarding the wing planform in a solar-powered high-altitude long-endurance unmanned aerial vehicle. A high-aspect-ratio wing has been widely adopted in this type of a vehicle, due to both the high lift-to-drag ratio and lightweight design. In the preliminary design, its characteristics need to be addressed correctly, and analyzed in an appropriate manner. In this paper, we use the three-dimensional Euler equation to analyze the wing aerodynamics. We also use an advanced structural modeling approach based on a geometrically exact one-dimensional beam analysis. Regarding the structural integrity of the wing, we determine detailed configuration parameters, specifically the taper ratio and the span length. Next, we conduct a multi-objective optimization scheme based on the response surface method, using the present baseline configuration. We consider the structural integrity as one of the constraints. We reduce the wing weight by approximately 25.3 % from that in the baseline configuration, and also decrease the power required approximately 3.4 %. We confirm that the optimized wing has sufficient flutter margin and improved static longitudinal/directional stability characteristics, as compared to those of the baseline configuration.

• The Journal of the Acoustical Society of Korea
• /
• v.22 no.7
• /
• pp.585-591
• /
• 2003

In this paper, fiber optic sensor using Fabry-Perot interferometer which had benefit of minimize and light-weight was used. The sensor head has 1cm in length, total length of fiber is 9.5 chi and the sensor supported at both ends, simply. To analyze the acoustic characteristic non-directional speaker is used as a sound source. Acoustic applied in lateral direction and detected two signals were compared each other. Below 1㎑ fiber optic sensor has more sensitive than microphone, but in 2㎑ fiber optic sensor has less sensitive than microphone. This characteristic varies to the supporting system of fiber optic sensor. It was confirmed that the Fabry-Perot interferometric sensor detected acoustic signal, effectively. This kind of sensor can be applied to the structural health monitoring field of intellectual structure.

• Journal of information and communication convergence engineering
• /
• v.7 no.2
• /
• pp.176-181
• /
• 2009

This study is part of a project to develop and improve mooring systems for oceanographic use that include an electro-optical sensor, 1MHz Nortek Aquadopp Doppler Profiler and AIRMAR multipurpose Sensor. The adaption of Doppler current profilers to measure directional wave spectra has provided a new instrumentation approach to coastal and nearshore oceanographic studies. The HEIOB is developed are light weight and of a compact design, and can be easily installed in marine environment. Since there are no base station and gateways in marine environments, we selected CDMA and Orbcomm to send the data information. Therefore, the data can be sent by either e-mail service or Short Message Service (SMS). This paper will present some of scientific sensor results regarding real-time oceanographic and meteorological parameters such as wind spend, wind direction, wave direction, and etc. The modeling and test results highlight the engineering challenges associated with designing these systems for long lifetimes. It can also be used in future application to build wave observation buoy network in real-time using multiple ubiquitous buoys that share wave data and allow analysis of multipoint, multi-layer wave profiler.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2002.11a
• /
• pp.169-174
• /
• 2002

It has known that the DCMP(Directionally Constrained Minimization of power)and the ZF(Zero Forcing) can improve the SINR performance of an array antenna system by using spatial signature of wireless channel. This paper analyzes performance of DCMP and ZF in multiple scattering environments. To obtain the spatial signature of wireless channel. bothe DOA(Directional of Arrival) and AS(Angular Spread) of the received signals were estimated by using ESPRIT. The performance of the DCMP and the ZF was analyzed theoretically. Through computer simulation, the SINR performance were evaluated.

• Journal of Power Electronics
• /
• v.16 no.2
• /
• pp.610-620
• /
• 2016

The compound active clamp zero voltage soft switching (CACZVS) three-phase power factor correction (PFC) converter has many advantages, such as high efficiency, high power factor, bi-directional energy flow, and soft switching of all the switches. Triple closed-loop PI controllers are used for the three-phase power factor correction converter. The control objectives of the converter include a fast transient response, high accuracy, and unity power factor. There are six parameters of the controllers that need to be tuned in order to obtain multi-objective optimization. However, six of the parameters are mutually dependent for the objectives. This is beyond the scope of the traditional experience based PI parameters tuning method. In this paper, an improved chaotic particle swarm optimization (CPSO) method has been proposed to optimize the controller parameters. In the proposed method, multi-dimensional chaotic sequences generated by spatiotemporal chaos map are used as initial particles to get a better initial distribution and to avoid local minimums. Pareto optimal solutions are also used to avoid the weight selection difficulty of the multi-objectives. Simulation and experiment results show the effectiveness and superiority of the proposed method.

• Explosives and Blasting
• /
• v.37 no.4
• /
• pp.17-25
• /
• 2019

The method to remove the head of the cast-in-place pile using the detonating cord and horizontal separation plate was proposed in this paper. Plain concrete block was fabricated. Through the blasting test of the concrete block, the charge weight and the burden required for cutting the pile head were identified. The degree of damage of concrete blocks after cutting the head was checked using AUTODYN 2D. As a result of the experiment, it was found that the concrete block was cut using the 10 g/m detonating cord and horizontal separation plate, and the directional cutting of the block using the horizontal separation plate and the block damage caused by the detonating cord were reduced.

• Tribology and Lubricants
• /
• v.18 no.2
• /
• pp.167-172
• /
• 2002

The wear behaviors of ultrahigh molecular weight polyethylene pins against titanium alloy and stainless steel disks moving in two different kinematic motion were investigated by conducting repeat pass rotational sliding and linear reciprocal sliding wear tests. Linear reciprocal motion wore more the polyethylene pin than did repeat pass rotational motion for both disk materials. It means that the repeated directional change of contact stresses generates more wear debris in polyethylene. For the linear reciprocal sliding tests, titanium alloy disks were damaged with some scratches after one million cycles but no surface damage was observed on the polyethylene pins. On the other hand, fur the repeat pass rotational sliding tests, all titanium alloy disks were severely abraded on the entire region of sliding track. This phenomenon can be interpreted by that stress fatigue under repeated sliding contact initiated titanium oxide layer wear particles from disk surface, and these hard particles were embedded into polyethylene pin and then they severely abraded the disk surface. From these results it can be concluded that the kinematic motion in pin-on-disk wear tests play a crucial role on the wear behaviors of UHMWPE pins against titanium alloy and stainless steef discs.

• The Journal of Korean Physical Therapy
• /
• v.16 no.3
• /
• pp.112-124
• /
• 2004

Purpose : The purpose of this study is to research the effects of the differences in shoe heel height on balanced performances with a balance master. Method : 40 healthy female adults were divided into 2 groups at random. All the female participants were tested by a balance master system. Differences were analyzed according to high heel shoes and low heel shoes. The ability of static postural balance control was measured by modified CTSIB and unilateral stance test, while that of dynamic postural balance control was measured by LOS (limit of stability) and rhythmic weight shift, among the programs of a balance master. Result : 1. There is no significant correlation between the ability of static and dynamic postural balance control before main test without the shoes. 2. Movement velocity and directional control ability were significant correlation compared result of in high heel shoes and low heel shoes group. Conclusion : In conclusion, the test results of the high heeled shoe group and the low heeled shoe group through a balance master system showed that the former one is inferior to the latter one.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.3
• /
• pp.501-507
• /
• 1999

At the mobile unit for adaptation the propagation environment, it is necessity to adapt very fast the weight coefficient vector of adaptive array antenna In this paper, for the BPSK and BFSK signals with S/I=2, S/N=10 subband adaptive array signal processing method to the linear array antenna using the LMS & the Kalman filter algorithm is proposed. For the 4 elements equidistance linear array antenna systems LMS and Kalman algorithms with subband adaptive instruction principles using the subband signal processing method are adopted and the computer simulation results to the constant amplitude envelope signals such as BPSK or BFSK can be seen that the convergence characteristics of directional patterns and the signal following characteristics are more fast and stable.