• Structural Engineering and Mechanics
• /
• 제76권5호
• /
• pp.619-629
• /
• 2020

In current study, surface/interface effects for pull-in voltage and viscous fluid velocity effects on dimensionless natural frequency (DNF) of fluid-conveying piezoelectric nanosensor (FCPENS) subjected to direct electrostatic voltage DC with nonlinear excitation, harmonic force and also viscoelastic foundation (visco-pasternak medium and structural damping) are investigated using Gurtin-Murdoch surface/interface (GMSIT) theory. For this analysis, Hamilton's principles, the assumed mode method combined with Lagrange-Euler's are used for the governing equations and boundary conditions. The effects of surface/interface parameters of FCPENS such as Lame's constants (λI,S, μI,S), residual stress (τ0I,S), piezoelectric constants (e31psk,e32psk) and mass density (ρI,S) are considered for analysis of dimensionless natural frequency respect to viscous fluid velocity u̅f and pull-in voltage V̅DC.

• Journal of Power Electronics
• /
• 제9권4호
• /
• pp.582-592
• /
• 2009

This paper proposes a new speed sensorless direct torque and flux controlled interior permanent magnet synchronous motor (IPMSM) drive. Closed-loop control of both the torque and stator flux linkage are achieved by using two proportional-integral (PI) controllers. The reference voltage vectors are generated by a SVM unit. The drive uses an adaptive sliding mode observer for joint stator flux and rotor speed estimation. Global asymptotic stability of the observer is achieved via Lyapunov analysis. At low speeds, the observer is combined with the high frequency signal injection technique for stable operation down to standstill. Hence, the sensorless drive is capable of exhibiting high dynamic and steady-state performances over a wide speed range. The operating range of the direct torque and flux controlled (DTFC) drive is extended into the high speed region by incorporating field weakening. Experimental results confirm the effectiveness of the proposed method.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 한국전산구조공학회 1999년도 봄 학술발표회 논문집
• /
• pp.121-128
• /
• 1999

This paper presents a time domain method for soil-structure interaction analysis for seismic loadings. It is based on the finite element formulation incorporating analytical frequency-dependent infinite elements for the far field soil. The dynamic stiffness matrices of the far field region formulated using the present method in frequency domain can be easily transformed into the corresponding matrices in time domain. At first, the equivalent earthquake forces are evaluated along the interface between the near and the far fields from the free-field response analysis carried out in frequency domain, and the results are transformed into the time domain. An efficient procedure is developed for the convolution integrals to evaluate the interaction force along the interface, which depends on the response on the interface at the past time instances as well as the concurrent instance. Then, the dynamic responses are obtained for the equivalent earthquake force and the interaction force using Newmark direct integration technique. Since the response analysis is carried out in time domain, it can be easily extended to the nonlinear analysis. Example analysis has been carried out to verify the present method in a multi-layered half-space.

• Journal of the Korean Society of Safety
• /
• 제30권6호
• /
• pp.26-33
• /
• 2015

This study suggests systematic procedures to improve safety policies on prevention of industrial accidents associated with industrial machines and devices. Specifically, new method of cause analysis of industrial accidents associated with industrial machines and devices is suggested and the related accident data are re-analyzed. Effectiveness of direct safety regulations such as safety certification, self-declaration of conformity, safety device regulation and safety inspection of industrial machines and devices are also analyzed. Based on those analysis results, transition from the current user-oriented safety device regulation to more balanced direct regulations on both manufacturer and user is suggested. Together with severity and frequency of industrial accidents, unit severity and unit frequency need to be taken into account to further assess the risk associated with a particular industrial machine or device. Balance between safety regulations will be realized by proper adjustment of lists of safety certification and inspection, and certification and inspection standards. This will also guarantee the maximum benefit over cost in such safety regulations.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.1206-1208
• /
• 2001

Direct torque control(DTC) of AC motor has the fast torque and flux dynamic responses even though it has very simple scheme to implement. DTC is also very simple in its implementation because it needs only two hysteresis comparators and switching vector table for both flux and torque control. The amplitude of hysteresis band greatly influences on the drive performance such as flux and torque ripple, switching frequency and current harmonics. Therefore, authors analysis flux and torque hysteresis bands is suggested considering switching frequency and harmonic distortion of currents.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• 제13권2호
• /
• pp.182-191
• /
• 1988

A log periodic microstrip array antenna using direct coupling feeder is designed at the frequency 7.2-12.4GHz. Transmission line analysis method was used for the design of each antenna element in consideration of the effects of dielectric and conductor loss and the discontinuity, also the optimized feeding points were obtained for the impedance matching between a main transmission line and each antenna element. It is shown that the measured VSWR was less that 2.4 at the frequency 7.2-12.4GHz, and 53% bandwidth was achived.

• Proceedings of the IEEK Conference
• /
• 대한전자공학회 1999년도 추계종합학술대회 논문집
• /
• pp.784-787
• /
• 1999

This paper describes a direct digital frequency synthesizer using the CORDIC algorithm, which can be implemented efficiently for a digital sinusoid synthesis. To optimize the hardware design parameters, we perform numerical analysis of the quantization effects for the CORDIC-based architecture. A pipelined architecture is employed to obtain a high data throughput,. We estimate and summarize its hardware costs for a variable accuracy, and a CORDIC-based architecture for 9 bit accuracy is emulated in FPGA.

• Proceedings of the KOSOMBE Conference
• /
• 대한의용생체공학회 1996년도 추계학술대회
• /
• pp.225-228
• /
• 1996

ECG data are used for the diagnostic purposes with many clinical situations, especially heart disease. In this paper, an efficient ECG data compression technique by wavelet transform and high-speed vector quantization on PMS-B algorithm is proposed. In general, ECG data compression techniques are divided into two categories: direct and transform methods. The direct data compression techniques are AZTEC, TP, CORTES, FAN and SAPA algorithms, besides the transform methods include K-L, Fourier, Walsh, and wavelet transforms. In this paper, we applied wavelet analysis to the ECG data. In particular, vector quantization on PMS-B algorithm to the wavelet coefficients in the higher frequency regions, but scalar quantized in the lower frequency regions by PCM. Finally, the quantized indices were compressed by LZW lossless entropy encoder. As the result of simulation, it turns out to get sufficient compression ratio while keeping clinically acceptable PRD.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• 제23권2호
• /
• pp.153-163
• /
• 2010

In this paper a frequency response analysis using Krylov subspace-based model reduction and its design sensitivity analysis with respect to design variables are presented. Since the frequency response and its design sensitivity information are necessary for a gradient-based optimization, problems of high computational cost and resource may occur in the case that frequency response of a large sized finite element model is involved in the optimization iterations. In the suggested method model order reduction of finite element models are used to calculate both frequency response and frequency response sensitivity, therefore one can maximize the speed of numerical computation for the frequency response and its design sensitivity. As numerical examples, a semi-monocoque shell and an array-type $4{\times}4$ MEMS resonator are adopted to show the accuracy and efficiency of the suggested approach in calculating the FRF and its design sensitivity. The frequency response sensitivity through the model reduction shows a great time reduction in numerical computation and a good agreement with that from the initial full finite element model.

• Journal of the Korean Society of Safety
• /
• 제30권1호
• /
• pp.1-7
• /
• 2015

This study first addresses the ineffectiveness of indirect regulation on industrial machines. Analysis of causes of industrial accidents associated with industrial machines further reveals the fact that technical causes need to be resolved at the manufacturing stage to reduce the frequency and strength of industrial accidents. Balanced safety certification on manufacturers and safety inspection on users of industrial machines are then suggested to effectively resolve such technical causes. The effectiveness of such safety certification and safety inspection can be justified by cost-benefit analysis. Particularly, balance in expected benefits of safety certification and safety inspection is a key issue for validity of such analysis. The accumulated benefit-costs for press brake and portable sawing machine confirm the effectiveness of such safety system.