• The Korean Journal of Ceramics
• /
• 제4권3호
• /
• pp.199-203
• /
• 1998

$Pb(Zr, Ti)O_3$ (Pb:Zr:Ti=1:0.52:0.48) thin films were prepared on single crystal MgO(100) substrates by dipping-pyrolysis process using a solution of constituent metal naphthenates as starting materials. The solution was spin-coated onto substrate and the precursor films were pyrolyzed at $200^{\circ}C$ in air or at $200^{\circ}C$ in argon for 1, 2, 5 and 24h, followed by final heat treatment at $750^{\circ}C$. For all the films, highly (h00)/(00l)-oriented Pb$Pb(Zr, Ti)O_3$ thin films with smooth surfaces and crack-free were obtained, whereas thin film pyrolyzed in air for 24 h exhibited polycrystalline character. According to the pole-figure analysis, epitaxy of the product films was found to depend on pyrolysis atmosphere.

• 대한치과보존학회:학술대회논문집
• /
• 대한치과보존학회 2001년도 추계학술대회(제116회) 및 13회 Workshop 제3회 한ㆍ일 치과보존학회 공동학술대회 초록집
• /
• pp.569.1-569
• /
• 2001

The purpose of this investigation was to determine the effect of dipping in tooth reserving solution on bond strength of 4-META/MMA-TBB dentin bonding system. The flattened dentin surface of bovine lower incisor was used for this investigation. The tooth were dipped in the tooth reserving solution (ViaSpan; Du Pont Pharmatical / Teeth Server "NEO";Neo Dental Chemical products CO/LTD, Japan/ Saline, Fuso Chemical CO, LTD, Japan) for 30 min.(omitted)

• 한국정밀공학회지
• /
• 제18권2호
• /
• pp.111-118
• /
• 2001

Tungsten probe is the most important part of a probe card, which is widely used for the performance test of wafer chips. Electro chemical etching becomes an exclusive choice for mass production of the tungsten probes. In the mass production, not only the shape of the probe but also the shape distribution of machined probes is important. A new method is proposed for the mass production of the tungsten probes. Tungsten wires are separated by a distance, and dipped into electrolyte. The dipping rate is controlled to shape the probes. Several experimental tests are performed to study the machining characteristics. From the test results, machining parameters including electrical conditions and anode position showed significant influences on the shape, repeatability, precision and quality of sharp tips.

• 한국작물학회지
• /
• 제43권3호
• /
• pp.184-188
• /
• 1998

Four experiments were conducted to determine growth regulators, their concentrations and treatment time, rooting medium, and plant parts for optimum seedling propagation by stem cuttings in yacon (Polymnia sonchifolia Poepp. & Endl.). NAA was the most effective on rooting, and followed by IBA 2,4-D, and IAA. Dipping the base of cuttings in 50 or 100 ppm solutions of IBA increased rooting ratios. The 100 ppm solution of IBA was 14% higher than the 50 ppm solution for rooting ratios. Rooting medium with equal volumes of clay loam and sand was the most suitable for rooting of cuttings. Cuttings with both terminal bud and the first node or cuttings with both the first and second nodes were higher in rooting ratios than cuttings with only terminal bud or the first or second nodes. Days to rooting was not affected by plant parts.

• 한국표면공학회지
• /
• 제36권5호
• /
• pp.364-372
• /
• 2003

In continuous galvanizing process, dissolution of iron into molten zinc results in a fairly great amount of dross. In order to decrease dross, the amount of dissolved iron of strip in molten zinc was investigated in the range of 0∼0.22%Al content, 440∼$470^{\circ}C$ strip temperature and 3∼60 sec dipping time. Uniform Fe-Al-Zn inhibition layer was formed in the coating layer/strip interface not only in the grain boundary but also in the grain of substrate with the increase of Al content in the zinc pot, while the amount of iron dissolution was decreased. Inhibition layer was unstable as the dipping time and strip temperature increased and the amount of iron dissolution increased.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권11호
• /
• pp.561-565
• /
• 2004

SiO₂ thin films are fabricated using sol-gel method and dipping method. Gelation time is faster according to increasing the amount of H₂O except H₂O/Si(OC₂H/sub 5/)₄=4. Initial viscosity is highest at H₂O/Si(OC₂H/sub 5/)₄=6. Gelation time is faster according to increasing the amount of CH₃COOH. The relative dielectric constant of thin films decreases a little according to increasing the measuring frequency. The dielectric dissipation factor of thin films increases a little below 100kHz and it increases rapidly over 100kHz.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 춘계학술대회 논문집 유기절연재료 전자세라믹 방전플라즈마 연구회
• /
• pp.148-152
• /
• 2001

One set of MMIC library has been developed using gate recess etching by spin processor. It is superior than that of dipping Method in the uniformity and the reproducibility of gate recess. A DC characteristics of p-HEMT have a uniform characteristics in the whole wafer than that of dipping method. The low noise p-HEMT with the $0.6{\mu}m$ and $200{\mu}m$ of gate length and gate width, respectivily, has a uniform characteristics of Idss 130~145 mA, conductances 190~220mS/nm, and threshold voltage -0.7~-1.1V in the drain voltage of 2V.

• The Korean Journal of Ceramics
• /
• 제3권3호
• /
• pp.191-194
• /
• 1997

Epitaxial Pb(Zr, Ti)O3(PZT) thin films were prepared on MgO(100) substrates by dipping-pyrolysis (DP) process using metal naphthenates as starting materials, and effects of pyrolysis and final heat-treatment conditions on the film's orientation were investigated. Solid-state epitaxial growth of PZT proceeds at lower temperature around 650℃ from the precursor pyrolyzed at 350 and 500℃. The in-plane alignment of the PZT films depends not only on the final heat-treatment temperature but on the pyrolysis conditions; the films, pyrolyzed at a higher temperature for a short time, i.e., at 500℃ for 10 min, exhibited stronger orientation after the same final heat treatment at 650°∼750℃. The PZT films with the strongest orientation were prepared by pyrolysis under the above conditions followed by final heat treatment at 750℃.

• Macromolecular Research
• /
• 제11권2호
• /
• pp.110-114
• /
• 2003

When using the dipping method for crystal formation, mono-layered colloidal crystal structures depend upon the lift-up rate of a glass substrate. The mono-layered colloidal crystals showed the highest quality when the glass substrate was raised at a rate of 3 mm/min at 25 $^{\circ}C$ in a 1 wt% polystyrene colloidal suspension (ethanol medium). In addition, in order to obtain multiple-layered colloidal crystals, an external electric Held was introduced. Multiple-layered colloidal crystals were successfully obtained via this method. The colloidal particles were well ordered over large areas and assembled into a homogeneous structure.

• 한국표면공학회지
• /
• 제21권2호
• /
• pp.39-46
• /
• 1988

Corrosion behavior of 5-26wt% Ni-Zn electrodeposited alloys was investigated by means of dipping electrochmical polarization measurement and galvanic coupling test. The weight loss and anodic polarization curve of coatings were measured by means of dipping and polarization measurement respectively. The galvanic protection effect of alloy coatings was measured by galvanic coupling test and the surface morpholgy of coatings was observed after corrosion testing. Our findings support thous of previous investigations showing that ${\gamma}$single phase coatings, while galvanic pprotection effect of dual phase coatings improved in comparison with ${\gamma}$single phase coating. The formation of colony in coating of ${\gamma}$and η+${\gamma}$ dual phsae caused the localized corrsion and increased the corrosion rate of the Ni-Zn coating.