• 한국세라믹학회지
• /
• 제47권2호
• /
• pp.195-198
• /
• 2010

It has been considered to apply GDC ($Gd_{0.1}Ce_{0.9}O_{1-X}$) for low-temperature SOFC electrolytes because it has higher ionic conductivity than YSZ at low temperature. However, open circuit voltage with using GDC ($Gd_{0.1}Ce_{0.9}O_{1-X}$) electrolyte in SOFCs, becomes lower than using YSZ (8 mol% Yttria stabilized Zirconia) electrolyte because GDC has electronic conductivity. In this work, the effect of changing GDC electrolyte thickness on the open circuit voltage has been investigated. Ni-GDC anode-supported unit cells were fabricated as follows. Mixed NiO-GDC powders were pressed and pre-sintered at $1200^{\circ}C$. And then, GDC electrolyte material was dip-coated on the anode and sintered at $1400^{\circ}C$. Finally the LSCF-GDC cathode material was screen-printed on the electrolyte and sintered at $1000^{\circ}C$. Electrolyte thickness was controlled by the number of dip-coating times. Open circuit voltage was measured depending on electrolyte thickness at $650^{\circ}C$ and found that the thicker GDC electrolyte was, the better OCV was.

• 한국세라믹학회지
• /
• 제46권5호
• /
• pp.534-539
• /
• 2009

Reaction Bonded Silicon Carbide(RBSC) has been used for engineering ceramics due to low-temperature fabrication and near-net shape products with excellent structural properties such as thermal shock resistance, corrosion resistance and mechanical strength. Recently, attempts have been made to develop hot gas filter with gradient pore structure by RBSC to overcome weakness of commercial clay-bonded SiC filter such as low fracture toughness and low reliability. In this study a fabrication process of porous RBSC with multi-layer pore structure with gradient pore size was developed. The support layer of the RBSC with multi-layer pore structure was fabricated by conventional Si infiltration process. The intermediate and filter layers consisted of phenolic resin and fine SiC powder were prepared by dip-coating of the support RBSC in slurry of SiC and phenol resin. The temperature of $1550^{\circ}C$ to make Si left in RBSC support layer infiltrate into dip-coated layer to produce SiC by reacting with pyro-carbon from phenol resin.

• Corrosion Science and Technology
• /
• 제16권2호
• /
• pp.69-75
• /
• 2017

Zinc coating on carbon steels give the higher corrosion resistance in chloride containing environments and in carbonated concrete. However, hydrogen evolution accompanies the corrosion of zinc in the initial activity in fresh concrete, which can lead to the formation of a porous structure at the reinforcement -concrete interface, which can potentially reduce the bond-strength of the reinforcement with concrete. The present study examines the mechanism of the corrosion of hot-dip galvanized steel in detail, as in the model pore solutions and real concrete. Calcium ion plays an important role in the corrosion mechanism, as it prevents the formation of passive layers on zinc at an elevated alkalinity. The corrosion rate of galvanized steel decreases in accordance with the exposure time; however, the reason for this is not the zinc transition into passivity, but the consumption of the less corrosion-resistant phases of hot-dip galvanizing in the concrete environment. The results on the electrochemical tests have been confirmed by the bond-strength test for the reinforcement of concrete and by evaluating the porosity of the cement adjacent to the reinforcement.

• 대한기계학회논문집B
• /
• 제29권10호
• /
• pp.1156-1162
• /
• 2005

In this study, a noble method is proposed to prevent the edge overcoating (EOC) that may develop near the edge of the steel strip in the gas wiping process of continuous hot-dip galvanizing. In our past study (Trans. of the KSME (B), Vol. 27, No. 8, pp. $1105\~1113$), it was found that EOC is caused by the alternating vortices which are generated by the collision of two opposed jets in the region outside the steel strip. When the two opposed jets collide at an angle much less than $180^{o}$, non-alternating stable vortices are established symmetrically outside the steel strip, which lead to nearly uniform pressure on the strip surface. In order to deflect both jets downward by a certain angle, a cylinder with small diameter is installed tangentially to the exit of the lower lip of the two-dimensional jet. In order to find an optimum cylinder diameter, the three dimensional flow field is analysed numerically by using the commercial code, STAR-CD. And the coating thickness is calculated by using an integral analysis method to solve the boundary layer momentum equation. In order to compare the present noble method with the conventional baffle plate method to prevent the EOC, the flow field with a baffle plate is also calculated. The calculation results show that the tangentially installed cylinder at the bottom lip of the jet exit is more effective than the baffle plate to prevent EOC.

• 멤브레인
• /
• 제29권6호
• /
• pp.362-376
• /
• 2019

본 연구에서는 열유도상분리법(thermally induced phase separation)을 사용하여 제조한 플라워 형태의 단면을 갖는 PVDF [poly(vinylidene fluoride)] 중공사 분리막에 대한 친수화 코팅과 그에 따른 특성평가에 대한 연구를 수행하였다. 연구에 사용한 중공사 분리막은 (주)퓨어엔비텍에서 제조한 PVDF 소재의 분리막이었으며, 친수화 코팅 실험은 PEBAX 1657, 2533, 3533의 공중합체 고분자를 사용하여 농도가 다른 용액을 제조 후 딥 코팅 방법을 이용하여 실시하였다. 친수화 코팅이 된 중공사 분리막은 친수화 정도를 파악하기 위하여 SEM 촬영 및 접촉각 측정을 실시하였다. SEM 촬영 결과 코팅의 농도가 증가하고 코팅횟수가 증가할수록 코팅층의 두께가 두꺼워짐을 확인하였고, 접촉각 측정의 경우 코팅의 농도가 증가하고 코팅횟수가 증가할수록 접촉각이 낮아짐을 확인하였다. 기체 투과 실험 결과 코팅농도가 증가하고 코팅횟수가 증가할수록 산소 기체투과량이 감소하였으며 친수성이 높은 PEBAX 1657로 코팅한 중공사의 기체투과량이 PEBAX 2533과 3533으로 코팅된 중공사보다 낮은 기체투과량을 가짐을 확인하였다.

• 한국세라믹학회지
• /
• 제45권10호
• /
• pp.579-583
• /
• 2008

A porous $Al_2O_3$, scaffold coated with tricalcium phosphate(TCP) was fabricated by replica method using polyurethane(PU) foam as a fugitive material. Successive coatings of $Al_2O_3$ and hydroxyapatite(HAp) were applied via dip coating onto polyurethane foam, which has a slender and well interconnected network. A porous structure was obtained after sequentially burning out the foam and then sintering at $1500^{\circ}C$. The HAp phase was changed to TCP phase at high temperature. The scaffold showed excellent interconnected porosity with pore sizes ranging from $300{\sim}700{\mu}m$ in diameter. The inherent well interconnected structural feature of PU foam remained intact in the fabricated porous scaffold, where the PU foam material was entirely replaced by $Al_2O_3$ and TCP through a consecutive layering process. Thickness of the $Al_2O_3$ base and the TCP coating was about $7{\sim}10{\mu}m$ each. The TCP coating was homogeneously dispersed on the surface of the $Al_2O_3$ scaffold.

• 한국세라믹학회지
• /
• 제42권3호
• /
• pp.165-170
• /
• 2005

Sol-gel 공정에 의해 제조된 세라믹 분리 막은 보다 순수한 재료를 이용할 수 있고, 균일성을 향상시킬 수 있을 뿐 아니라 다양한 복합체도 넓은 범위에서 반응을 유도할 수 있다는 장점을 가지고 있어 많은 연구가 진행되고 있다. 본 연구에서는 sc,1-gel 공정을 이용하여 Tetraethyl ortho-silicate(TEOS)-Polyethylene glycol(PEG)계 organically modified silicate(ORMOSt)sol을 합성하였다. Polymer분자량을 변수로 하여 sol 합성 후 특성 변화를 점도와 겔화 시간을 측정함으로써 관찰하였다. 합성된 sol을 다공성 담체 위에 dip-coating법을 이용하여 막을 제조하였으며, SEM관찰을 통해 분리 막의 미세구조를 확인하였다. 합성 복합 막의 Oil/water 에멀젼의 처리효율을 cross-flow 타입의 막 분리 장치를 이용하여 확인하였다. Ormosilsol은 유기물의 분자량이 증가될수록 보다 쉽게 코팅 층을 형성 시킬 수 있었고, 담체를 용매에 담지 시켜 코팅 물질이 담체의 기공내로 침투될 때의 모세관력을 줄임으로써 크랙이 방지된 얇은 막을 얻을 수 있었다. Colloidal sol 코팅 막에 비해 ormosil sol코팅 막은 분리효율 뿐 아니라 flux 특설이 시험 5분경과 시점에서 약 $200\;l/m^2h$이상 향상되었음을 확인 할 수 있었다.

• 보존과학회지
• /
• 제28권1호
• /
• pp.53-62
• /
• 2012

행정박물이란 공공기관의 업무수행과 관련된 유형적 증거물로, 독특하고 유일하며 특정 사건, 시간, 또는 인물을 표현하는 정보적인 가치를 지니고 있다. 근대문화유산으로써의 가치를 지니고 있는 행정박물은 그 중요성에 비해 체계적으로 분류 관리 보존하는 지침은 마련되지 않았다. 이 중 금속제 행정박물의 경우 보존처리 및 연구사례가 적고 복합적인 행정적 가치를 지니고 있어 일반화된 발굴유물의 보존처리 과정을 적용하기 어렵다. 그러므로 본 연구에서는 강화처리에 초점을 두어 동합금 행정박물의 표면강화처리에 알맞은 재료와 적용방법을 실험을 통해 찾아보고자 하였다. 현재 사용하고 있는 Wax 3종과 발굴유물에 사용하는 아크릴계 수지를 선정하여 종류와 코팅방법에 따른 특성을 비교 분석하였다. 표면관찰, 박막 두께, 접착력, 접촉각 및 표면에너지, 황변실험 등 일련의 분석을 통해 코팅 특성을 비교한 결과, 아크릴계 수지를 행정박물에 사용해도 무방하나 기존에 사용하던 Wax B를 Dip-coating 한 후 가열처리하여 강화처리하는 것이 가장 우수한 강화효과를 얻을 수 있음을 확인하였다.

• Bulletin of the Korean Chemical Society
• /
• 제31권2호
• /
• pp.360-364
• /
• 2010

$Li_4Ti_5O_{12}$ thin film with inverse hemispheric structure was fabricated on a Pt/Ti/$SiO_2$/Si substrate by the sol-gel and dip coating method for use as an anode for 3-dimensional (3D) thin-film batteries. Polystyrene (PS) beads of 400 nm diameter were used to prepare the template for the inverse hemispheric structure. A coating solution prepared using precursor sources was dropped on the template-deposited substrates, which were then calcinated at $400^{\circ}C$. The template was removed by calcination, and the inverse hemispheric structure was successfully formed by an annealing process. The cyclic performance during high-rate charge/discharge processes of the $Li_4Ti_5O_{12}$ film with inverse hemispheric structure was superior to that of the flat $Li_4Ti_5O_{12}$ film.

• 한국세라믹학회지
• /
• 제32권4호
• /
• pp.516-524
• /
• 1995

In this study, to prepare the dielectric (Ba, Sr)TiO3 thin films by the sol-gel process, Titaminum (IV) sio-propoxide (Ti[OCH(CH3)2]4), Ba and Sr acetate were used for sol and thin films were prepared by dip-coating process. Stability of sol decreased with the increase of Sr, and thickness of thin films were obtained 0.13~0.17${\mu}{\textrm}{m}$ by 1 coating cycle. Transmittance of amorphous thin films heated at 500 and 55$0^{\circ}C$ was very good, and crystallization tendency of thin films according to heat-treatment temperature and crystallization characteristics of thin films heated at 11$0^{\circ}C$ for 3 hrs were analysed. As a result, good perovskite structure was obtained higher than 100$0^{\circ}C$, and tetragonality of thin film was decreased but pyrochlore was formed with increasing Sr. In case of addition to substitute 0.4mol% Sr for Ba, dielectric constant was 288 and loss factor (tan $\delta$) was 0.04.