• Geophysics and Geophysical Exploration
• /
• v.17 no.2
• /
• pp.58-65
• /
• 2014

We studied the source mechanisms of very-long-period event recorded at seismic station WIZ near White Island Volcano, New Zealand on August 4, 2012. Since seismic data at only one station were available, we conducted moment tensor inversion using three simplified models (explosion, crack, and pipe models). To constrain the moment tensor solution of seismic event, we computed synthetic data for each model to compare with observed data. Type and orientation for the best model is a crack at a depth of 1600 m with a dip of $80^{\circ}NE$ and a strike of $N80^{\circ}W$. We interpret that a deep explosion may have opened a crack for gases to escape, and the upward gas flow triggered the surface explosions four hours later as confirmed by a webcam. The interpretation based on moment tensor inversion is consistent with previous studies of geochemical data of the volcanic island.

• Journal of the Korean Ceramic Society
• /
• v.32 no.5
• /
• pp.617-625
• /
• 1995

In order to reduce reflectance of soda-lime glass having average reflectance of 7.35% and refractive index of 1.53, single (SiO2), double (SiO2/20SiO2-80ZrO2), and triple (SiO2/ZrO2/75SiO2-25ZrO2) layers were designed and fabricated on the glass substrate by Sol-Gel method. Stble sols of SiO2-ZrO2 binary system for antireflective (AR) coatings were synthesized with tetraethyl orthosilicate (TEOS) and zirconium n-butoxide as precursors and ethylacetoacetate (EAcAc) as a chelating agent in an atmosphere environment. Films were deposited on soda-lime glass at the withdrawal rates of 3~11 cm/min using the prepared polymeric sols by dip-coating and they were heat-treated at 45$0^{\circ}C$ for 10 min to obtain homogeneous, amorphous and crack-free films. In case of SiO2-ZrO2 binary system, refractive index of film increased with an increase of ZrO2 mol%. Designed optical constant of films could be obtained through varying the withdrawal rate. In the visible region (380~780nm), reflectance was measured with UV/VIS/NIR Spectrophotometer. Average reflectances of the prepared single-layer [SiO2 (n=1.46, t=103nm)], double-layer [SiO2 (n=1.46, t=1-4nm)/20SiO2-80ZrO2 (n=1.81, t=82nm)], and triple-layer [SiO2 (n=1.46, t=104nm)/ZrO2 (n=1.90, t=80nm)/75SiO2-25ZrO2 (n=1.61, t=94 nm)] were 4.74%, 0.75% and 0.38%, respectively.

• Journal of Sensor Science and Technology
• /
• v.17 no.5
• /
• pp.369-374
• /
• 2008

A novel fiber optic surface plasmon resonance (SPR) sensor using cyclic olefin copolymer (COC) prism with the spectral modulation is presented. The SPR sensor chip is fabricated using the SU-8 photolithography, Ni-electroplating and COC injection molding process. The sidewall of the COC prism is partially deposited with Au/Cr (45/2.nm thickness) by e-beam evaporator, and the thermal bonding process is conducted for micro fluidic channels and optical fibers alignment. The SPR spectrum for a phosphate buffered saline (0.1.M PBS, pH.7.2) solution shows a distinctive dip at 1300.nm wavelength, which shifts toward longer wavelength with respect to the bovine serum albumin (BSA)concentrations. The sensitivity of the wavelength shift is $1.16\;nm{\cdot}{\mu}g^{-1}{\cdot}{\mu}l^{-1}$. From the wavelength of SPR dips, the refractive indices (RI) of the BSA solutions can be theoretically calculated using Kretchmann configuration, and the change rate of the RI was found to be $2.3{\times}10^{-5}RI{\cdot}{\mu}g^{-1}{\cdot}l^{-1}$. The realized fiber optic SPR sensor with a COC prism has clearly shown the feasibility of a new disposable, low cost and miniaturized SPR biosensor for biochemical molecular analyses.

• Journal of Broadcast Engineering
• /
• v.8 no.4
• /
• pp.365-380
• /
• 2003

Since MPEG-21 IPMP has been working on International Standardization activity such as one of DRM systems from 1997, the standardization is recently re-started even though the activity was interrupted. According to the MPEG Brisbane meeting, the CfR of MPEG-21 IPMP will be determined on the next Hawaii meeting, therefore they will announce the CfP. However the CfP announced in MPEG Hawaii meeting but the CfR didn't announce because of unfinished requirement document job. Finally. the proposed techniques will be submitted till June 2004. In this paper, we explained the requirement of standardization based on a broadcasting circumstance and implemented the system of MPEG-21 including the architecture and IPMP systems, then we showed all functionality within the other MPEG-21 elements engines. In case of multimedia stream broadcasting system, it is a real-time processing system, the implemented MEPG-21 Architecture can be shown the use of Digital Item In the MPEG-21 terminal and additional MPEG-21 element engines.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.82-84
• /
• 2003

Watershed boundaries and flow paths within the watershed are the most important factors required in watershed analysis. Most often the derivation of watershed boundaries and stream network and flow paths is based on topographical maps but spatial variation of flow direction is not clearly understandable using this method. Water resources projects currently use 1: 50, 000-scale ground survey or aerial photography-based topographical maps to derive watershed boundary and stream network. In basins, where these maps are not available or not accessible it creates a real barrier to watershed geo-spatial analysis. Such situations require the use of global datasets, like GTOPO30. Global data sets like ETOPO5, GTOPO30 are the only data sets, which can be used to derive basin boundaries and stream network and other terrain variations like slope aspects and flow direction and flow accumulation of the watershed in the absence of topographic maps. Approximately 1-km grid-based GTOPO 30 data sets can derive better outputs for larger basins, but they fail in flat areas like the Karkheh basin in Iran and the Amudarya in Uzbekistan. A new window in geo-spatial hydrology has opened after the launching of the space-borne satellite stereo pair of the Terra ASTER sensor. ASTER data sets are available at very low cost for most areas of the world and global coverage is expected within the next four years. The DEM generated from ASTER data has a reasonably good accuracy, which can be used effectively for hydrology application, even in small basins. This paper demonstrates the use of stereo pairs in the generation of ASTER DEMs, the application of ASTER DEM for watershed boundary delineation, sub-watershed delineation and explores the possibility of understanding the drainage flow paths in irrigation command areas. All the ASTER derived products were compared with GTOPO and 1:50,000-based topographic map products and this comparison showed that ASTER stereo pairs can derive very good data sets for all the basins with good spatial variation, which are equal in quality to 1:50,000 scale maps-based products.

• Tunnel and Underground Space
• /
• v.8 no.4
• /
• pp.296-306
• /
• 1998

Ongoing huge Bakun Hydropower project is including the construction of a 210 m height hydroelectric rockfill dam with an installed capacity of 2,520 MW and a power transmission system connecting to the existing networks between Sarawak and peninsula Malaysia. In order to allow the main dam construction during the dry season, the Ballui river will have to be detoured through 3 concrete lined diversion tunnels with an internal diameter of 12 m and a length of 1,400 m each. The geology of Bakun site belongs to the several thousand meters thick Belaga formation deposited from the late Cteteceous to the early Teriary in the Northwest Borneo geosyncline. The orientation of the bedding plane, strike at N55$^{\circ}$E to N70$^{\circ}$E and dip at 50$^{\circ}$SE to 70$^{\circ}$SE, is developed uniformly in Bakun sedimentary rocks. Rock mechanical characteristics of Bakun site have been classified into 4 rock mass types(RMT) depending on the degree of weathering and the occurrence of rock jointing with RMR. Graywacke(Sandstone) as well as Shale can take place together in the same rock mass type if their rock mass properties are similar. It was summarized the rock support type and support system design of underground diversion tunnels in view of rock mechanics.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.292.2-292.2
• /
• 2013

Graphene, a two-dimensional graphite material consisting of sp2-hybridized carbons. The properties of graphene such as extremely high carrier mobility, high thermal conductivity, low resistivity, large specific make it a promising materail of divices and material. Typically, poly (methyl methacrylate) (PMMA) is used when graphene transfer to other substrates. To remove PMMA on graphene, people used to dip the graphene into the acetone. However, it is known that the remove of PMMA on the graphene is difficult to completely using the acetone. Therefore, to remove the PMMA on the graphene surface, many research groups have employed various methods such as the thermal treatment, photothermal method, and other solvent. Nevertheless, a part of PMMA still remain on graphene surface. Usually, to observe the residual PMMA on graphene surface, topography of graphene surface scanned by atomic force microscopy is used. However, in that case, we can not distinguish PMMA and other particles. In this study, to confirm the residual PMMA on graphene surface, we employed novel measurement technique which is available to distinguish PMMA and other particles by means of photothermal effect.

• Korean Journal of Materials Research
• /
• v.22 no.7
• /
• pp.335-341
• /
• 2012

Recently, the demand for the miniaturization of printed circuit boards has been increasing, as electronic devices have been sharply downsized. Conventional multi-layered PCBs are limited in terms their use with higher packaging densities. Therefore, a build-up process has been adopted as a new multi-layered PCB manufacturing process. In this process, via-holes are used to connect each conductive layer. After the connection of the interlayers created by electro copper plating, the via-holes are filled with a conductive paste. In this study, a desmear treatment, electroless plating and electroplating were carried out to investigate the optimum processing conditions for Cu via filling on a PCB. The desmear treatment involved swelling, etching, reduction, and an acid dip. A seed layer was formed on the via surface by electroless Cu plating. For Cu via filling, the electroplating of Cu from an acid sulfate bath containing typical additives such as PEG(polyethylene glycol), chloride ions, bis-(3-sodiumsulfopropyl disulfide) (SPS), and Janus Green B(JGB) was carried out. The desmear treatment clearly removes laser drilling residue and improves the surface roughness, which is necessary to ensure good adhesion of the Cu. A homogeneous and thick Cu seed layer was deposited on the samples after the desmear treatment. The 2,2'-Dipyridyl additive significantly improves the seed layer quality. SPS, PEG, and JGB additives are necessary to ensure defect-free bottom-up super filling.

• Journal of Fashion Business
• /
• v.21 no.6
• /
• pp.16-30
• /
• 2017

Currently, e-textile market is rapidly expanding and the emerging area of e-textiles requires electrically conductive threads for diverse applications, including wearable innovative e-textiles that can transmit/receive and display data with a variety of functions. This study introduces hybrid nano-structures which may help increase the conductivity of the textile threads for use in wearable and flexible smart apparels. For this aim, Ag was selected as a conductive material, and yarn treatment was implemented where silver nanowire (AgNW) and graphene flake (GF) hybrid structures overcome the limitations of the AgNW alone. The yarn treatment includes several treatment conditions, e.g., annealing temperature, annealing time, binder material such as polyurethane (PU), coating time, in order to search for the optimum method to form stable conductive nano-scale composite materials as thin film on the surface of textile yarns. Treatedyarns showed improved electrical resistance readings. The functionality of the spandex yarn as a stretchable conductive thread was also demonstrated. When the yarn specimens were treated with colloid of AgNW/GF, relatively good electrical conductivity value was obtained. During the extension and recovery cycles of the treated yarns, the initial resistance values did not deteriorate significantly, since the network of nanowire structure with the support of GF and polyurethane stayed flexible and stable. Through this research, it was found that when one-dimensional structure of AgNW and two-dimensional structure of GF were mixed as colloids and treated on the surface of textile yarns, flexible and stretchable electrical conductor could be formed.

• Economic and Environmental Geology
• /
• v.21 no.3
• /
• pp.235-255
• /
• 1988

Talc deposit of pipe-like form occurrs in the lower part of the Hyangsanri Dolomite with a strike of N40 -50 E and a dip of 40 -50 NW which is one formation of the Ogcheon Super Croup. The pipi-like ore body plunge at about $40^{\circ}$ to the west and are parallel to the lineation developed in the area. Structural formulae of tales occurred in this deposit are close to the ieal composition $Mg_6Si_8O_{20}(OH)_4$ showing limited deviation from ideal one. Substitution of Al for Si in tetrahedral site is of little or nothing ranging 0-0.04 and octahedral occupancy is close to six ranging 5.88-5.98 atoms per unit cell. Predominant octahedaral cation is Mg and proportion of divalent cations is generally over 97percent. Calcite -dolomite thermometry is obtained by determining the mol % $MgCO_3$using of EPMA and XRD methods. The peak metamorphic temperature can be estimated at $470{\pm}30^{\circ}C$ in the area whereas carbonates occurred at near talc ore show lower temperature than $400^{\circ}C$ that the calcite solvus limit is not well established. It indicates that the talc deposit was formed at the lower temperature that the metamorphic temperature. Cosequently, the formation of talc by metamorphism is questionable and the alteratin zone developed around the talc ore is very limited. The occurrence of talc ore in the dolomite as well as mineralogy, calcite-dolomite geothermometry, chlorite geothermometry, field and microscopic evidence suggest that siliceous ascending hydrothermal solution along the fracture is responsible for the formation of talc. It was considered that the slight fracturing of dolomite was formed by deformation prior to the mineralization.