• Journal of Korean Society for Geospatial Information Science
• /
• v.24 no.2
• /
• pp.71-78
• /
• 2016

After the 'Guidelines for the preservation of digital heritage' were published by UNESCO, interests in the fabrication of digital cultural heritage have been increasing throughout the world. The present study was intended to fabricate digital cultural heritages for existing cultural properties using the reverse engineering technology and obtain two-dimensional drawings. Jinju Castle Gongbukmun, which is a cultural property, was selected as a study subject and 3D modeling of Jinju Castle Gongbukmun was conducted by implementing 3D scanning and processing the point cloud data. Using the Gongbukmun 3D model (3D-Gongbukmun) made as such, requirements as a digital heritage were reviewed and 2D drawings of Gongbukmun such as front views, ground plans, and side views could be prepared.

• Korean Journal of Digital Imaging in Medicine
• /
• v.6 no.1
• /
• pp.24-30
• /
• 2003

Flat-panel detector(FPD) is the driving force for realizing the next gene ration of x-ray system. In this study, we developed amorphous selenium(a-Se) based flat-panel digital X-ray detector(DXD) for radiography. The prototype detector consists of an amorphous selenium layer and a thin-film transistor(TFT) array. Comparing to other papers1)-4), optimization of amorphous selenium and progress of evaporation were similar. The pixel pitch of fabricated detector was $139{\mu}m$, fill factor was 86%, and the size was 14"${\times}$8.5". Hand and test bar pattern images were acquired. A high modulation transfer function(MTF) factor was obtained: 58% at 3.0 lp/mm.

• Journal of Power Electronics
• /
• v.9 no.3
• /
• pp.410-417
• /
• 2009

This paper represents a design and implementation of a digital controller for a multi-phase synchronous buck converter (SBC) using a digital signal processor (DSP). The multi-phase SBC has generally been used for a voltage regulation module (VRM) of a microprocessor because of its high current handling capability at a low output voltage. The VRM requires high control performance of tight output regulation, high slew rate, and load sharing capability of multiple converters. In order to achieve these requirements, the design and implementation of a digital control system for a multi-phase SBC are presented in this paper. The digital PWM generation, current sensing, and voltage and current controller using a DSP TMS320F2812 are considered. The experimental results are provided to show the validity of the implemented digital control system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.936-941
• /
• 2005

To achieve rapid developments and ensure competitiveness, cost saving, digital manufacturing is essential in die shops. Digital Manufacturing is a technology to facilitate effective product developments and agile productions by digital environments representing the physical and logical schema and the behavior of real manufacturing system including manufacturing resources, processes and products. For applying digital manufacturing to die shop, engineering information managements of products, manufacturing process and resources are needed. In this paper proposes and implements, PLM approach for achieving engineering collaborations in engineering activities. We suggest detail procedures, some examples and considerations of PPR managements in die shop.

• Smart Structures and Systems
• /
• v.30 no.1
• /
• pp.35-47
• /
• 2022

Data-driven engineering is crucial for information delivery between design, fabrication, assembly, and maintenance of prefabricated structures. Design for manufacturing and assembly (DfMA) is a critical methodology for prefabricated bridge structures. In this study, a novel concept of digital engineering model that combined existing knowledge of DfMA with object-oriented parametric modeling technologies was developed. Three-dimensional (3D) geometry models and their data models for each phase of a construction project were defined for information delivery. Digital design models were used for conceptual design, including aesthetic consideration and possible variation during fabrication and assembly. The seismic performance of a bridge pier was evaluated by linking the design parameters to the calculated moment-curvature curves. Control parameters were selected to consider the tolerance control and revision of the digital models. Digitalized fabrication of the prefabricated members was realized using the digital fabrication model with G-code for a concrete printer or a robot. The fabrication error was evaluated and the design digital models were updated. The revised fabrication models were used in the preassembly simulation to guarantee constructability. For the maintenance of the bridge, the as-built information was defined for the prefabricated bridge piers. The results of this process revealed that data-driven information delivery is crucial for lifecycle management of prefabricated bridge piers.

• 제어로봇시스템학회:학술대회논문집
• /
• 1989.10a
• /
• pp.760-765
• /
• 1989

Digital control laws are implemented on an active magnetic bearing system with DSP. The results of tests using a experimental apparatus are (1) in a case that conventional PID, PIDD2 controls are employed, implemention of digital control law has similar characteristics to that of analogue control law. (2)The experiments reveal the results that the dynamic compensation based on the observer may be better than that of the other conventional controllers.

• Journal of Practical Engineering Education
• /
• v.9 no.1
• /
• pp.41-48
• /
• 2017

In this paper, we proposed a method for digital logic circuit control, through arduino device programming with digital outputs, to design a curriculum for basic digital logic circuit practices. Curricula for arduino device programming and digital logic circuit are essentially practiced in engineering departments of colleges or high schools in South Korea. However, actual practice course lacks the experimental examples of digital logic circuit combined with arduino device programming. Furthermore, actual practice course lacks the curriculum in that students design and test their own digital logic circuits with the less cost than the oscilloscope. Therefore, to solve these problems in this paper, we proposed a curriculum for basic digital logic circuit practices during one semester. In this curriculum, students control and experiment their own digital logic circuits through arduino device programming with digital outputs.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.4
• /
• pp.7-15
• /
• 1993

This paper introduces a new concept to analyze the digital control system where the continuous-time plant is stabilized by the digital controller with sampler and hodl. It gives some methods to handle the inter-sampling behavior which has not been considered in the digital controller design. Also, the new trend and future direction in digital control are introduced.

• Korean Journal of Computational Design and Engineering
• /
• v.21 no.1
• /
• pp.9-19
• /
• 2016

Applying human engineering simulation to analyzing work capability and movements of operators during manufacturing is highly demanded. However, difficulty in modeling digital human required for simulation makes engineers to be reluctant to utilize human simulation for their tasks. This paper addresses such problem on human engineering simulation by developing the technology to automatize human modeling with multiple Kinects at different depths. The Kinects enable us to acquire the movements of digital human which are essential data for implementing human engineering simulation. In this paper, we present a system for modeling automation of digital human. Especially, the system provides a way of generating the digital model of workers' movement and position using multiple Kinects which cannot be generated by single Kinect. Lastly, we verify the effects of the developed system in terms of modeling time and accuracy by applying the system to four different scenarios. In conclusion, the proposed system makes it possible to generate the digital human model easily and reduce costs and time for human engineering simulation.

• Proceedings of the IEEK Conference
• /
• 2002.07a
• /
• pp.152-155
• /
• 2002

In this paper, a new approach is proposed for the error detection dedicated to MPEG-4 video coding by using the digital watermarking. In the process of encoding, the proposed scheme abstracts the macroblock features of headers, motion vectors, and Discrete Cosine Transform (DCT) coefficients, which are embedded in the quantized DCT coefficients as the digital watermarks. The decoder performs the accurate error detection through the watermark extraction. Simulation results demonstrate that the error detection ability of the proposed approach can be significantly enhanced, and that digital watermark embedding incurs little degradation to the picture quality.