• Journal of the Korean Society for Marine Environment & Energy
• /
• v.1 no.2
• /
• pp.40-51
• /
• 1998

The interaction of contained oil slicks with current was investigated with a two-dimensional experimental setup in the circulating water channel facility. A vertical plate was used to contain the oils against the currents and the evolution of the oil slick, mainly focusing on the water/oil interface, was examined with an aid of a laser sheet. Two different oils - soy bean oil and diesel oil - were studied with varying the current speed (10 cm/sec to 35 cm/sec), the barrier depth (4 cm and 8 cm) and the volume of oil (2 liter to 12 liter). Different types of the interface behavior were observed according to the conditions and their mechanism was discussed based basically on the dimensional analysis. The critical speeds of two types of oil loss mechanism (entrainment failure and drainage failure) were also examined.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.10
• /
• pp.1251-1256
• /
• 2014

The use of lubrication oil is of many purposes and one among them is to drive the engine mounted on a ship. Hence the supply of clean lubrication oil is important. And an oil purifier is one of key components in marine diesel engines. At present, the element type full-flow oil filter has been widely used for cleaning the engine oil. The self-driven centrifugal oil purifier is a device which is used to remove the impurities in lubrication oil using a jet flow. The flow characteristics and the physical behaviors of particles in this self-driven oil purifier were investigated numerically and the filtration efficiencies were evaluated. For calculations, a Computational Fluid Dynamics method is used and the Shear Stress Transport turbulence model has been adopted. The Multi Frames of Reference method is used to consider the rotating effect of the flows. The influence of centrifugal forcehas been numerically investigatedto improve filtration efficiency of tiny particles. As a result of this research, it was found that the particle filtration efficiency using the only center axis rotating and outer wall rotating system are higher than that of the fully rotating system in the self-driven oil purifier.

• Journal of the Korean Society of Safety
• /
• v.34 no.6
• /
• pp.22-28
• /
• 2019

In South Korea, the enact of Korean Coast Guard Act-1 manages physical and chemical oil-dispersants. Oil snare, which is made of polypropylene, is newly added to the aforementioned act, and it has advantage on the ease of recovery compare to other adsorbents. This study synthesized bunker B-oil with diesel-oil and bunker C-oil to perform an adsorption test based on three samples which were manufactured in South Korea. As a result, adsorption test revealed 5.2 g/g more adsorption than the previous results from the act. Additional toluene test revealed that all the samples satisfied 90.0%, however coloured samples could release its pigment on the marine environment. Thus, colorless samples are recommended on the risk management of marine accidents. The study on the basic direction of the calculation of the test items and the standard value for the quality control of the oil snare was also carried out.

• Journal of Power System Engineering
• /
• v.10 no.4
• /
• pp.50-55
• /
• 2006

An efficient cooling system for a piston of an automotive engine is very important. Therefore a large capacity gasoline engine or diesel engine has adopted the direct injection cooling system to increase its cooling efficiency. In this direct cooling system, an cooling oil is injected to a piston directly using an oil jet and this cooling oil flows through an oil gallery inside the piston. Flow rate and injection accuracy of this cooling oil are very important because these are main factors that have influence on its efficiency. The purpose of this study is to understand the changes of flow characteristics with various curvatures and diameters of an outlet nozzle and to check whether engine oil enters into the oil gallery well or not. From this study, we found that secondary flow was formed in a curved part of jet due to centrifugal force and irregular flow pattern appeared at the jet outlet. This pattern has influence on flow characteristics of engine oil entering the gallery. These simulation results have a good agreement with experiments.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.4
• /
• pp.836-847
• /
• 2016

Water soluble oil was obtained by pyrolysis of biomass. The characteristics of emulsified fuel by mixing water soluble oil and MDO(marine diesel oil) and engine emissions were studied with engine dynamometer. Saw dust was used as biomass. Water soluble oil was obtained by condensing of water and carbon content with pyrolysis of saw dust at $500^{\circ}C$. Emulsion fuel was obtained by emulsifying MDO and water soluble oil by the water soluble oil mixing ratio of 10 to 20% of MDO. Exhaust gas detection was performed with engine dynamometer. While combustion, micro-explosion took place in the combustion chamber by water in the emulsion fuel, emulsion fuel scattered to micro particles and it caused to smoke reduction. The heat produced from water vapour reduce the temperature of internal combustion chamber and it caused to inhibition of NOx production. It can be verified by the lower exhaust temperature of each ND-13 mode using emulsion fuel than that of MDO fuel. The NOx and smoke concentration were reduced by increasing water soluble oil content in the emulsion fuel. The power also decreased according to the increment of water soluble oil content of emulsion fuel because emulsion fuel has low calorific value due to high water content than MDO. As a result of ND-13 mode test with 20% bio oil content, it was achieved 25% reduction in NOx production, 60% reduction in smoke density, and 15% reduction in power loss.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.46 no.4
• /
• pp.487-494
• /
• 2010

In order to test the applicability of bunker-A in a diesel engine for small-fishing boat, the investigation of the engine performance and the exhaust emission was performed under various conditions of fuel property, intake air pressure and fuel temperature. It was also performed based on IMO NOx Technical code. At high load, the energy consumption rate of bunker-A was lower than that of diesel oil, and the characteristics of exhaust emission of bunker-A were similar to those, and NOx emission rates of both fuels satisfied the IMO NOx emission regulation limits. The energy consumption rate and characteristics of exhaust emission were improved as the intake air pressure was increased, but these were not improved remarkably as the temperature of bunker-A was heated. However, at low load the energy consumption rate, CO emission rate and HC emission rate of bunker-A were higher than those of diesel oil, but NOx emission rates of the fuels were about the same. In addition, at low load the energy consumption rate and CO emission rate of bunker-A were increased as the intake air pressure and the temperature were higher than normal conditions. Accordingly, it is thought that the use of bunker-A in a kind of test engine is possible at high load. On the other hand, it is thought that more research is needed to improve the combustion efficiency under low temperature and low load condition.

• Journal of Power System Engineering
• /
• v.20 no.2
• /
• pp.51-57
• /
• 2016

Non-esterified biodiesel fuel is cheaper than esterified that because of a simple manufacturing process that only consists of filtering. Applicability of this on diesel engine with electronic control system was accomplished, then optimization adopting a fractional factorial design and response surface methodology was carried out at 25% and 50% of engine load in this study. Pressure of common rail and injection timing mainly effected on responses as specific fuel oil consumption and nitrogen oxides regardless of engine load. Estimations were 310.3 g/kWh of specific fuel oil consumption and 237 ppm of nitrogen oxides at 25% load, and 233.2 g/kWh of specific fuel oil consumption and 730 ppm of nitrogen oxides at 50% load. Tests to verify these estimations were accomplished and as the results, specific fuel oil consumption was 300.4 g/kWh and NOx was 277 ppm at 25% load and 236.8 g/kWh and 573 ppm at 50% load.

• Tribology and Lubricants
• /
• v.32 no.4
• /
• pp.132-139
• /
• 2016

The piston of a marine diesel engine works under severe conditions, including a combustion pressure of over 180 bar, high thermal load, and high speed. Therefore, the analyses of the fatigue strength, thermal load, clamping (bolting) system and lubrication performance are important in achieving a robust piston design. Designing the surface profile and the skirt ovality carefully is important to prevent severe wear and reduce frictional loss for engine efficiency. This study performs flexible multi-body dynamic and elasto-hydrodynamic (EHD) analyses using AVL/EXCITE/PU are performed to evaluate tribological characteristics. The numerical techniques employed to perform the EHD analysis are as follows: (1) averaged Reynolds equation considering the surface roughness; (2) Greenwood_Tripp model considering the solid_to_solid contact using the statistical values of the summit roughness; and (3) flow factor considering the surface topology. This study also compares two cases of skirt shapes with minimum oil film thickness, peak oil film pressure, asperity contact pressure, wear rate using the Archard model and friction power loss (i.e., frictional loss mean effective pressure (FMEP)). Accordingly, the study compares the calculated wear pattern with the field test result of the piston operating for 12,000h to verify the quantitative integrity of the numerical analysis. The results show that the selected profile and the piston skirt ovality reduce friction power loss and peak oil film pressure by 7% and 57%, respectively. They also increase the minimum oil film thickness by 34%.

• KSBB Journal
• /
• v.20 no.2 s.91
• /
• pp.84-87
• /
• 2005

Toxicity test for biodiesel (BD), biodiesel-derived neopentyl polyol ester (NPE) lubricant oil base, lubricant oil for diesel engine oil (LODE) and petroleum diesel (PD) was carried out using earthworm, Eisenia fefida. According to the method by OECD 207, the $LC_{50}$ values of BD and NPE were estimated as 2,450 and 1,528 mg/kg, respectively, which indicate that these compounds are classified as slightly toxic compounds. The $LC_{50}$ values of LODE and PD were estimated as 500 and 603mg/kg, respectively, showing that theses compounds are evaluated as moderately toxic compounds.

• 한국생물공학회:학술대회논문집
• /
• 2003.04a
• /
• pp.164-168
• /
• 2003

Fatty acid methyl esters (FAMEs) show large potential applications as diesel substitutes, and they are known as biodiesel fuel. Biodiesel fuel as a renewable energy is an alternative that can reduce energy dependence on petroleum and air pollution. Several processes for the production of biodiesel fuel have been developed. Transesterification process under alkali-catalysis and short-chain alcohol gives high level yield of methyl esters in short reaction times. In this research, transesterification of rapeseed oil was investigated to produce the FAMEs. Experimental reaction conditions included molar ratio of oil to alcohol, concentration of catalyst, types of catalysts, reaction time, and reaction temperature. The conversion ratio of rapeseed oil enhanced with the alcohol-oil mixing ratio and with the reaction temperature.