• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.2
• /
• pp.252-258
• /
• 2009

Engine bench tests has been done on a common-rail diesel engine with bio-diesel fuel to study effects of B100 and B20 on output power, fuel consumption and emissions. Test results show that B100 and B20 could reduce PM, HC, CO emission and smoke, but power decrease, fuel consumption increase and NOx increase obviously, B100 reduce PM and DS with $50%{\sim}70%$ and $80%{\sim}85%$ compared with diesel fuel, while B20 reduce PM and DS with $25%{\sim}35%$ and $30%{\sim}40%$. NOx of B100 and B20 increase $5%{\sim}20%$ compare to diesel.

• Tribology and Lubricants
• /
• v.25 no.2
• /
• pp.125-131
• /
• 2009

Biodiesel produced from triglyceride which is main component of animal fats and vegetable oils by methanolysis was known for excellent lubricity. In this study, the lubricity of 12 kinds of biodiesel come from vegetable oils were analyzed using HFRR(High frequency reciprocating rig). The biodiesel synthesized from soybean oil has best lubricity by $153{\mu}m$ of wear scar in HFRR and used fried oil's biodiesel has slightly low lubricity by $299{\mu}m$. Also we have found that the lubricity of diesel was improved when mixing ratio of soybean biodiesel was increased in base diesel.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 1998.11a
• /
• pp.201-205
• /
• 1998

Leakage of hydrocarbon compound from underground storage tank has been a significant issue to the hazard of environmental contaminants. It is therefore necessary to develop the measurement technique of hydrocarbon compound concentration. In this study, the possibility of TDR application to measure concentration of hydrocarbon compound, especially diesel, in a sandy soil was investigated. Experiments were conducted in two different conditions. The first one was to measure the resistances of the soil columns packed according to the various ratios of tab water and diesel content in the total voids. The other was to measure the resistance of the soil under the flow condition where diesel oil was allowed to infiltrate into the KCl-saturated soil column. The experimental results showed that there exists a significant relationship between oil% and TDR-measured resistance. This suggests that TDR can be an effective device to measure the concentration of hydrocarbon compound in a soil.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.5 no.1
• /
• pp.21-32
• /
• 2013

Marine transportation industry is undergoing a number of problems. Some of these problems are associated with conventional marine fuel-oils. Many researchers have showed that fuel-oil is considered as the main component that causes both environmental and economic problems, especially with the continuous rising of fuel cost. This paper investigates the capability of using natural gas and hydrogen as alternative fuel instead of diesel oil for marine gas turbine, the effect of the alternative fuel on gas turbine thermodynamic performance and the employed mathematical model. The results showed that since the natural gas is categorized as hydrocarbon fuel, the thermodynamic performance of the gas turbine cycle using the natural gas was found to be close to the diesel case performance. The gas turbine thermal efficiency was found to be 1% less in the case of hydrogen compared to the original case of diesel.

• International Journal of Fluid Machinery and Systems
• /
• v.8 no.1
• /
• pp.23-35
• /
• 2015

This paper presents the rotordynamic performance measurement of oil-free turbocharger (TC) supported on gas foil bearings (GFBs) for 2 liter class diesel vehicles and comparison to floating ring bearings (FRBs). Oil-free TC was designed and developed via the rotordynamic analyses using dynamic force coefficients from GFB analyses. The rotordynamics and performance of the oil-free TC was measured up to 85 krpm while being driven by a diesel vehicle engine, and compared to a commercial oil-lubricated TC supported on FRBs. The test results showed that the GFBs increased the rotor speed by ~ 20% at engine speeds of 1,500 rpm and 1,750 rpm, yielding the reduction of turbine input energy by more than 400 W. Incidentally, an external shock test on the oil-free TC casing was conducted at the rotor speed of 60 krpm, and showed a good capability of vibration damping due to the well-known dry friction mechanism of the GFBs.

• Journal of Microbiology and Biotechnology
• /
• v.11 no.4
• /
• pp.607-613
• /
• 2001

The biodegradation rates of diesel oil by a selected diesel-degrading bacterium, Pseudomonas stutzeri strain Y2G1, and microbial consortia composed of combinations of 5 selected diesel-degrading bacterial were determined in liquid and soil systems. The diesel degradation rate by strain Y2G1 linearly increased $(R^2=0.98)$ as the diesel concentration increased up to 12%, and a degradation rate as high as 5.64 g/l/day was obtained. The diesel degradation by strain Y2G1 was significantly affected by several environmental factors, and the optimal conditions for pH, temperature, and moisture content were at pH8, $25^{\circ}C$, and 10%, respectively. In the batch soil microcosm tests, inoculation, especially in the form of a consortium, and the addition of nutrients both significantly enhanced the diesel degradation by a factor of 1.5 and 4, respectively. Aeration of the soil columns effectively accelerated the diesel degradation, and the initial degradation rate was obviously stimulated with the addition of inorganic nutrients. Based on these results, it was concluded that the major rate-limiting factors in the tested diesel-contaminated soil were the presence of inorganic nutrients, oxygen, and diesel-degrading microorganisms. To resolve these limiting parameters, bioremediation strategies were specifically designed for the tested soil, and the successful mitigation of the limiting parameters resulted in an enhancement of the bioremediation efficiency by a factor of 11.

• Journal of Korean Society on Water Environment
• /
• v.22 no.5
• /
• pp.824-830
• /
• 2006

Several tests were conducted to optimize the design parameters of ln-situ soil flushing processes for diesel contaminated soil. According to the batch extraction test for three anionic surfactants evaluation, Calgonit limiting bubble occurrence was selected for its higher oil cleaning efficiency. After optimum surfactant selection, there were many sets of column flushing test. Over 70% of BTEX was removed in this surfactant dose with 400% of soil volume. In the case of no surfactant addition flushing in column, so called "blank flushing test", BTEX removal rate was 64%. But when we reused the effluent for the cleaning solution, the removal rate was decreased to 46.9%. This result showed reabsorption of oil occurred on the soil. With the addition of Calgonit solution to the diesel contaminated column, BTEX was removed up to 98.9% during the first flushing and 99.4% for the second recirculation flushing. In microcosm tests, diesel contaminated soils were cleaned by both surfactant flushing and biological activities. In anoxic condition, nitrate was used as an electron acceptor while the surfactant and the oil were used an electron donor. BTEX removal efficiency could be achieved up to 80% by biological degradation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.1
• /
• pp.60-65
• /
• 2017

We designed and fabricated the engine oil monitoring sensor to measure engine oil deterioration through increased vehicle mileage. Since the condition of the engine oil can be affected by the state of the vehicle and its operating conditions, it should be directly measured and determined in every vehicle. The fabricated sensor has an aluminum parallel capacitor structure that measures capacitance related with the dielectric constant, which is one of the indices of oil deterioration. The size of the capacitor is small enough that it could be easily adapted on the oil level gauge without introducing any change in the design. The fabricated device is installed in the diesel engine to measure the change in capacitance accurately as the vehicle moved from 0 km (new engine oil state) to 11,364 km. The results showed the maximum value at around 5,000 km, and the values plateaued as mileage increased, corresponding with the measurement result of the TAN (Total Acid Number). Based on the results, the condition of the oil must be monitored regularly though oil change is recommended once the vehicle has traveled the distance of around 10,000 km.

• Journal of the Korean Applied Science and Technology
• /
• v.28 no.4
• /
• pp.508-516
• /
• 2011

Hydrotreated biodiesel(HBD) is paraffinic bio-based liquid, with the chemical structure $C_nH_{2n+2}$, originating from vegetable oil(the process can also be applied to animal fat). The oil or fat is treated in a number of process, the most important being hydrogenation, in order to create a bio-based liquid diesel fuel. During the hydrogenation, oxygen is removed from the triglyceride and converted into water. Propane is formed as a by product and can be combusted and used for energy production. HBD can be used in conventional diesel engines, pure or blended with conventional diesel, due to its similar physical properties to diesel. This study reports the quality characteristics with chemical and physical properties as an alternative diesel fuel. Especially, HBD showed higher cetane value and number than FAME, and it is consisted of $C_{15}$ - $C_{18}$ n-paraffinic compounds. We also describes quality characteristics of HBD blends(2, 5, 10, 20, 30, 40, 50 vol%) in automotive diesel. HBD blends(max. 20 vol%) were the limit by the Korean specification due to poor low temperature characteristics.

• Tribology and Lubricants
• /
• v.13 no.2
• /
• pp.46-51
• /
• 1997

Crosshead bearings in two-stroke marine diesel engines are operated under severe conditions of lubrication because the load on the bearing is unidirectional and the sliding speed is very low and oscillatory. In this paper, the motion of journal in a bearing is investigated using the lubrication theory. Several locus paths are presented to show the effects of oil groove size, bearing clearance and oil inlet pressure. It is found that the minimum film thickness is affected by the oil groove and bearing clearance, and the oil groove is an important design factor.