• Journal of Mechanical Science and Technology
• /
• 제17권1호
• /
• pp.146-156
• /
• 2003

A numerical algorithm is developed to analyze the performance of a Unit-injector (UI) System for a diesel engine. The fundamental theory of the algorithm is based on the continuity equation of fluid dynamics. The loss factors that should be seriously regarded on the continuity equation are the compressibility effect of liquid fuel, the wall friction loss in high-pressure fuel lines of the system, the kinetic energy loss of fuel in the system, and the leakage of fuel out of the control volume. For an evaluation of the developed simulation algorithm, the calculation results are compared with the experimental outputs provided by the Technical Research Center of Doowon Precision Industry Co. (DPICO) ； the maximum pressure in the plunger chamber (P$\_$p/) and total amount of fuel injected into a cylinder per cycle (Q$\_$f/) at each operational condition. The result shows that the average error rate (%) of P$\_$p/ and Q$\_$f/ are 2.90% and 4.87%, respectively, in the specified operational conditions. Hence, it can be concluded that the analytical simulation algorithm developed in this study can be reasonably applied to the performance prediction of newly designed UI system.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.899-905
• /
• 2000

The characteristics of air flow and engine performance with swirl ratio variance of intake port In a turbocharged DI diesel engine was studied in this paper. The intake port flow is important factor which have influence on the engine performance and exhaust emission because the properties in the injected fuel depend on the combustion characteristics. The swirl ratio for ports was modified by hand-working and measured by impulse swirl meter. For the effects on performance and emission, the brake torque and brake specific fuel consumption were measured by engine dynamometer and NOx, smoke were measured by gas analyzer and smoke meter. As a result of steady flow test, when the valve eccentricity ratio are closed to cylinder wall, the flow coefficient and swirl intensity are increased. And as the swirl ratio is increased, the mean flow coefficient is decreasing, whereas the gulf factor is increasing. Also, through engine test its can be expected to meet performance and emission by optimizing the main parameters; the swirl ratio of intake port, injection timing and compression ratio.

• 한국분무공학회지
• /
• 제24권4호
• /
• pp.178-184
• /
• 2019

Diesel engines have the advantages of higher thermal efficiency and lower CO2 emissions than gasoline engines, but have the disadvantages that particulate matter (PM) and nitrogen oxides (NOx) emissions are greater than those of gasoline engines. In particular, nitrogen oxides (NOx) emitted from diesel engines generates secondary ultrafine dust (PM2.5) through photochemical reactions in the atmosphere, which is fatal to humans. In order to reduce nitrogen oxides (NOx), pre-treatment systems such as EGR, post-treatment systems such as LNT and Urea SCR have been actively studied. The Urea SCR consists of an injection device injecting urea agent and a catalytic device for reducing nitrogen oxides (NOx). The nitrogen oxide (NOx) reduction performance varies greatly depending on the urea uniformity in the exhaust pipe. In this study, spray characteristics according to the spray hole structure were confirmed, and the influence of spray uniformity on spray characteristics was studied through engine evaluation.

• 한국수소및신에너지학회논문집
• /
• 제27권6호
• /
• pp.727-736
• /
• 2016

Numerical simulations of n-heptane spray characteristics in a constant volume combustion chamber under diesel engine like conditions with increasing ambient gas density ($14.8-142kg/m^3$) and ambient temperature (800-1000 K) respectively were performed to understand the non-vaporizing and vaporizing spray behavior. The effect of fuel temperature (ranging 273-313 K) on spray characteristics was also simulated. In this simulation, spray modeling was implemented into ANSYS FORTE where the initial spray conditions at the nozzle exit and droplet breakups were determined through nozzle flow model and Kelvin-Helmholtz/Rayleigh-Taylor (KH-RT) model. Simulation results were compared with experimentally obtained spray tip penetration result to examine the accuracy. In case of non-vaporizing condition, simulation results show that with an increment of the magnitude of ambient gas density and pressure, the vapor penetration length, liquid penetration length and droplet mass decreases. On the other hand vapor penetration, liquid penetration and droplet mass increases with the increase of ambient temperature at the vaporizing condition. In case of lower injection pressure, vapor tip penetration and droplet mass are increased with a reduction in fuel temperature under the low ambient temperature and pressure.

• 한국자동차공학회논문집
• /
• 제8권2호
• /
• pp.9-18
• /
• 2000

Combustion and emission characteristics in a direct injection diesel engine is closely related to the intake port system. It is therefore important to understand the swirl flow characteristics formed by a helical intake port. However there are still many uncertainties. The purpose of this experimental study is to investigate the effects of the valve eccentricity ratio and the inlet flow conditions of a helical intake port on the characteristics of an in-cylinder swirl flow. A steady state flow test rig consisted of ISM(impulse swirl meter), LFM(laminar flow meter) and cylinder head with a helical intake port was used. The swirl ratio(Rs) and mean flow coefficient(Cf(mean)) with inlet flow conditions were measured. The results of these experiment can be summarized as follows. Swirl flow characteristics of a helical intake port are affected by the inlet flow conditions, and especially they are much affected by the length of a manifold runner and the rotational angle of a curved manifold runner.

• Journal of Advanced Marine Engineering and Technology
• /
• 제40권3호
• /
• pp.180-184
• /
• 2016

국제기구 및 각국의 정부는 인간의 건강 및 환경을 보호하기 위해 선박의 배기가스 규제를 엄격히 적용하고 있다. 함정은 이러한 배기가스 규제 적용 대상에서 제외되고 있지만 최근 미국, 영국 등 일부 선진국에서는 함정으로 야기되는 대기환경오염을 방지하기 위해 전기추진체계 시스템을 도입하는 등 다양한 개선 방법을 적용하고 있다. 본 연구에서는 함정용 디젤엔진의 매연 발생 문제 해결을 위해 노즐 직경을 축소 변화시키고 분사압력을 증가시켜 배기가스 발생량 측정과 오염물질조사 방법론을 이용해 저부하시 매연 문제가 개선된 것을 확인하였다. 동시에 그 영향을 유량방정식과 함정시험평가서를 통해 노즐 직경 축소 결과 연료 소비량이 감소되는 것을 확인하였다.

• 대한기계학회논문집B
• /
• 제26권9호
• /
• pp.1276-1283
• /
• 2002

Recently, HSDI (High Speed Direct Injection) diesel engine has been spotlighted as a next generation engine because it has a good potential for high thermal efficiency and fuel economy. This study was carried out to investigate the in-cylinder flow characteristics generated in a 4-valve small diesel cylinder head with a tangential and helical intake port. The flow characteristics such as coefficient of flow rate(Cf), swirl ratio (Rs), and mass flow rate (ms) were measured in the steady flow test rig using the impulse swirl meter and the analysis of in-cylinder flow field was conducted by experiment using the PIV and calculation using the commercial CFD code. As the results from steady flow test indicate, the mass flow rate of the cylinder head with a short distance between the two intake ports is increased over 13% than that of the other head. However, the non-dimensional swirl ratio is decreased approximately 15%. From in-cylinder flow characteristics obtained by PIV and CFD calculation, we found that the swirl center was eccentric from the cylinder center and the velocity distribution became uniform near the TDC. In addition, the results of the calculation are good agreement with the experimental results.

• 한국해양환경ㆍ에너지학회지
• /
• 제7권4호
• /
• pp.174-179
• /
• 2004

현재 국내 엔진 제작사에서 주로 이용하는 NOx 저감 기술은 low NOx fuel nozzle과 연료분사시기 조정과 같든 엔진 개량방법이지만, 향후 NOx에 대한 규제가 강화될 것을 대비하여 고효율의 NOx 제거기술(EGR, Dn, SCR 등) 도입과 정책적 지원이 요구된다. 또한, THC, PM, CO 등에 대한 추가 규제가 예상되므로 기타 대기오염물질을 제거할 수 있는 DPF/CDPF DOC, HCC 등의 기술을 선박에 도입하기 위한 연구가 이루어져야 한다. 선박에서 발생하는 대기오염물질을 규제하기 위한 법률의 제ㆍ개정시에는 내륙에서 운항되는 유람선 등에 대한 규제가 동시에 이루어져야 할 것이다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권9호
• /
• pp.1051-1056
• /
• 2014

아산화질소($N_2O$, Nitrous Oxide)는 박테리아의 물질대사와 같은 생물학적인 활동에 의하여 자연적으로 발생한다. 하지만, 최근의 대기 중 $N_2O$는 산업의 성장과 같은 인간의 활동에 의하여 증가되어져 왔다. 이 중에 대기 중의 $N_2O$농도를 증가시키는 요인들 중에 하나는 선박용 연료 연소로부터 발생하는 $N_2O$이다. 현재 해상 운송은 국제 물류의 99퍼센트 이상을 담당하고 있고, 선박척수는 물동량의 증가와 함께 증가하고 있다. 따라서, 본 연구에서는 4-행정 선박용 디젤엔진을 사용하여 다른 성분 농도들을 포함하는 연료의 연소가 $N_2O$ 배출률에 미치는 영향에 대하여 실험적인 조사를 실시하였다. 또한, 연소실 내의 연료 연소 패턴이 $N_2O$ 배출률에 미치는 영향에 대하여 평가하였다.

• 에너지공학
• /
• 제16권3호
• /
• pp.120-127
• /
• 2007

본 연구의 목적은 디젤연소장의 분위기조건에 따라 다성분 혼합연료의 질량분률이 분무착화 및 연소특성에 미치는 영향을 실험적으로 고찰하는데 있다. 착화 및 연소특성은 화학발광계측법 및 직접촬영법을 이용하여 분석되었다. 실험은 광계측기를 사용하여 RCEM에서 이루어졌으며, 이소옥탄, 노말 도데칸, 노말 헥사데칸으로 혼합한 다성분연료는 커먼레일 인젝터의 전자제어에 의해 RCEM의 연소실 내로 분사된다. 실험조건은 분사압력 42, 72, 112 MPa과 분위기온도 700, 800, 900 K로 하였다. 그 결과로서 착화지연은 고세탄가성분에 의존하고, 분위기온도가 낮을 경우 저비점성분 혼합비율의 증가에 따라 휘도영역이 현저하게 낮아지며, 열발생률이 증가하면서 확산연소기간을 단축시킨다.