• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.5
• /
• pp.1-10
• /
• 1998

A GaAs MMIC composed of VCO (voltage controlled oscillator) and mixer for PCS receiver has been developed using 1.mu.m ion implanted GaAs MESFET process. The VCO consists of a colpitts-type oscillator with a dielectric resonator and the circuit configuration of the mixer is a dual-gate type with an asymmetric combination of LO and RF FETs for the improvement of intermodulation characteristics. The common-source self-biasing is used in all circuits including a buffer amplifier and mixer, achieving a single power supply (3V) operation. The total power dissipation is 78mW. The VCO chip shows a phase noise of-99 dBc/Hz at 100KHz offset. The combined VCO/mixer chip shows a flat conversion gain of 2dB, the frequency-tuning factor of 80MHz/volts in the varacter bias ranging from 0.5V to 0.5V , and output IP3 of dBm at varactor bias of 0V. The fabricated chip size is 2.5mm X 1.4mm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.408-411
• /
• 2004

The electrical stability against surge stress of ZPCCY-based varistors were investigated at different sintering times. Sintering time decreased the varistor voltage and nonlinear exponent from 279.6 to 179.1 and from 52.5 to 24.9, respectively. On the contrary, the leakage current and dielectric dissipation factor increased from 1.2 to 9.8 ${\mu}A$ and from 0.0461 to 0.0651 with increase of sintering time. For all varistors, the variation rates of V-I characteristic parameters against surge stress were affected in order of varistor voltage$\rightarrow$nonlnear exponent$\rightarrow$leakage current. On the whole, the electrical stability against surge stress increased with increasing sintering time. Conclusively, it is assumed that the varistor sintered for 2 h exhibited comparatively good characteristics, in view of overall characteristics.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1896-1898
• /
• 2002

In this paper, to developing thermally and mechanically upgraded ones, we dismounted pole transformers used in the fields for over 13 years and conducted aged oil analysis. Also, when the cellulose and aramid papers in test cell were aging with oil at $130^{\circ}C$ for 3000 hours, with the testing period cellulose paper deteriorated more rapidly than the others. For example dielectric strength and dissipation factor of papers deteriorated with aging time. For evaluation of thermal aging characteristics, a mineral oil-immersed transformer was constructed with hybrid insulation system comprised of aramid paper and cellulose insulation. A Hybrid system has economic advantages. Cellulose materials are confined to cooler regions of the transformer winding. And aramid papers are served to insulate contact parts of hot conductors.

• Applied Science and Convergence Technology
• /
• v.24 no.6
• /
• pp.215-218
• /
• 2015

A pyroelctric properties of Ni(x)-doped PMNT systems were analyzed. Modified PMNT samples were prepared using the columbite structure method. Pyroelectric current, polarization, dielectric constant and dissipation factor of Ni-doped PMNT samples were measured as a function of temperature. By adding a small amount of NiO, pyroelectricity of PMNT is increased. Unlike the normal $ABO_3$ ferroelectric, Ni-doped PMNT showed properties for relaxor ferroelectric of causing the successive phase transition over a wide temperature. The optimum conditions for obtaining compositions with improvement ferroelectric properties are a nominal addition of 0.02 mole% Ni. Also, Ni-doped PMNT ferroelectric showed excellent pyroelectric figures of merit in the vicinity of room temperature. The pyroelectric coefficient ($0.00524C/m^2K$ at $25^{\circ}C$) and figures of merit ($F_v{\sim}0.039m^2/C$ and $F_d{\sim}0.664{\times}10^{-4}Pa^{-1/2}$) of composition PMNT with 0.02 mole% Ni are comparable to the earlier reports on lead-type pyroelectrics.

• Journal of the Microelectronics and Packaging Society
• /
• v.2 no.1
• /
• pp.29-34
• /
• 1995

Glass 물질을 첨가하여 저온소결한(Ba, Sr, Ca) TiO3 세라믹 유전체의 전기 및 기계 적 특성을 조사하였다. PbO-ZnO-B2O3 계 glass를 첨가하여 소결온도를 135$0^{\circ}C$ to 105$0^{\circ}C$ With 4wt% of glass material the sintered specimen at 115$0^{\circ}C$ for 2hrs showed a dielectric constant over 8000 with low dissipation factor. As fired ceramic capacitor satisfied the Z5U( +10~ +85$^{\circ}C$; +22% ~-56%) specifications of the EIAs. The mechanical hardness and toughness of glass reacted ceramics slightly decreased but it hows higher hardness and toughness values than Lead perovskite dielectrics.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1351-1353
• /
• 1994

High strengh pocelain insulators with 35wt% alumina were manufactured by wet produce technique. The microstructure and crystalline phases of this samples and the effect of CaO addition to insulator bodies were studied. Electrical and mechanical properties (permittivity, dissipation factor, modulus of rupture, Young's modulus etc,) were studied. The relation between microstructure and electrical, mechanical properties were analyzed.

• The Korean Journal of Ceramics
• /
• v.1 no.4
• /
• pp.204-208
• /
• 1995

The microstructure and electrical propetries were investigated for polycrystalline $Ba^{1-x}Sr_xTiO_3$(BST) thin films deposited on Pt/Ti/$SiO_2$(PTSS) and Pt/MgO(PM) substrates by metalorganic chemical vapor deposition (MOCVD). BST films on PTSS have coulmnar and porous structures, while on PM have an equiaxied and dense structure. The dielectric constant and a dissipation factor of BST films on PTSS and 20 fC/$\mu \textrm{cm}^3$ on PTSS and 12fC/$\mu \textrm{cm}^2$ on PM was obtained at an applied electric field of 0.06 MV/cm. Leakage current density of BST films on PM was smaller than that on PTSS. The leakage current density level was about $8\times10^{-8}A/\textrm{cm}^2$ at 0.04MV/cm.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.3
• /
• pp.528-531
• /
• 1994

Digitalization in electronic system is required the capacitor which have a large capacitance with small size, low impedance at high frequency, and high reliability. The fabrication and its properties of aluminum solid electrolytic capacitor are investigated. Employing conduction polymer film such as, polypyrrole as solid electroylte, solid type aluminum electrolytic capacitors were made. The surface of insulationg oxide is covered with conducting polymer layer prepared by chemical oxidative polymerization. Thereafter this conducting layer is covered with conducting polymer prepared by electrochemical polymerization. The dielectric properties of these capacitors were also measured and discussed. Regarding on frequency characteristics of the trial made capacitor, impedance and ESR at high frequency is lower than those of the stacked type film capacitor. It is alo confirmed that temperature coefficient of capacitance and dissipation factor of the capacitor are lower than those of film capacitor and liquid type aluminum electrolytic capacitor.

• Electrical & Electronic Materials
• /
• v.11 no.10
• /
• pp.53-59
• /
• 1998

Paraelectric lead landthanum titanate(PLT) thin films have been prepared by a reactive dc magnetron sputtering system using a multicomponent metal target. The surface area control of each element on the target markedly facilitates the fabrication of thin films of complex ceramic compounds. A postdeposition heat-treatment was applied to all as-deposited PLT thin films at annealing temperatures up to 75$0^{\circ}C$ for crystalization. The composition of the PLT(28) thin filmannealed at $650^{\circ}C$ was: Pb, 0.73; La, 0.28; Ti, 0.88; O, 2.9. The dielectric constant and dissipation factor of the thin film(200 nm) at low filed measurements (500 Vcm-1) are 1216 and 0.018, respectively. The charge storage density using a typical Sawyer-Tower circuit with a 500 Hz sine wave was 12.5 $\mu$Ccm-2 at the electric field of 200 kVcm-1.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.7
• /
• pp.572-577
• /
• 2001

The electrical properties of Pr$_{6}$ O$_{11}$ -based ZnO varistors consisting of ZnO-Pr$_{6}$ O$_{11}$ -CoO-Cr$_2$O$_3$-Er$_2$O$_3$ ceramics were investigated with sintering temperature in the range of 1325~f1345$^{\circ}C$. As sintering temperature is raised., the nonlinear exponent was increased up to 1335$^{\circ}C$, reaching a maximum 70.53, whereas raising sintering temperature further caused it to decrease, reaching a minimum 50.18 and the leakage current was in the range of 1.92~4.12 $\mu$A. The best electrical properties was obtained from the varistors sintered at 1335$^{\circ}C$, exhibiting a maximum (70.53) in the nonlinear exponent and a minimum (1.92 $\mu$A) in the leakage current, and a minimum (0.035) in the dissipation factor. On the other hand, the donor concentration was in the range of (0.90~1.14)x10$^{18}$ cm$^{-3}$ , the density of interface states was in the range of (2.69~3.60)x10$^{12}$ cm$^{-2}$ , and the barrier height was in the range of 0.77~1.21 eV with sintering temperature. With raising sintering temperature, the variation of C-V characteristic parameters exhibited a mountain type, reaching maximum at 134$0^{\circ}C$. Conclusively, it was found that the V-I, C-V, and dielectric characteristics of Pr$_{6}$ O$_{11}$ -based ZnO varistors are affected greatly by sintering temperature.