• The Journal of Korean Academy of Prosthodontics
• /
• v.37 no.5
• /
• pp.640-650
• /
• 1999

As an optimal quality of the restorations, there should be a least amount of seating discrepancy between the casting and abutment teeth. However, high viscosity of the cementing medium and its resulting thickness may prevent complete seating of the restoration. The use of die spacing material provides adequate internal relief for the cementing medium. The purpose of this study is to compare the thickness of three commonly used die spacing materials. Materials and Methods: Stone plates were fabricated and divided into 12 sections to be painted with die spacers. Tru-Fit, Whip-Mix and Belle do St. Claire die spacer which are commonly used in dental practice were tested in this study. Each die spacers were painted layer by layer according to the manufacturer's recommendation. The average thickness of each die spacers were measured with light microscope(${\times}100$) and compared between them. Results and Conclusions. A silver-colored Tru-Fit die spacer has the lowest value of thickness without statistical significance comparing with a gold-colored Tru-Fit die spacer and a gray layer of Whip-Mix die spacer has the highest value of thickness without any statistical significance comparing with Belle de St. Claire die spacer. Three and four layers of Tru-Fit die spacer and two layers of Whip-Mix and Belle de St. Claire die spacers seem to be in the acceptable range of thickness of 25 to $45{\mu}m$ for optimal seating of the restorations. The standard experimental design and method should be fur thor evaluated for more consistent and objective results.

• Journal of the Korean institute of surface engineering
• /
• v.40 no.4
• /
• pp.197-202
• /
• 2007

Fit of the restoration and its cementation procedure is crucial to both its short and long term prognosis. Marginal fit is affected by many variables during the fabrication process. These variables, being intrinsic properties of the materials or the clinical technique used, can cause changes in the size and shape of the definitive restoration. Even if all variables are controlled carefully, the seating of a restoration can still be affected due to insufficient space for the luting agent. The use of die spacer can reduce the elevation of a cast restoration of a prepared tooth, decreased seating time, improve the outflow of excess cement, and lower the seating forces. The purpose of this study was to evaluate the marginal fidelity according to die spacer application times and measurement site. Casting alloys were prepared and fabricated using non-precious metal at $950^{\circ}C$. Specimens are divided into four groups: I(die spacer painted casting for wax pattern), II(die spacer non painted casting for wax pattern). The specimens were cut and polished for marginal gap observation. The marginal gap was observed using scanning electron microscopy (SEM).

• Restorative Dentistry and Endodontics
• /
• v.20 no.1
• /
• pp.152-163
• /
• 1995

This experiment was performed to observe the adhesion pattern and microleakage in the gingival margin according to variation in the resin cement thickness which results from thickness of Die spacer. which is considered to effect the adaptability of the composite resin inlays. Clearfil CR inlays were fabricated on stone models with CR Sep applicated once and Nice fit twice, 4 times, and 6 times each. After 2nd curing within the CRC-100 oven, CR inlays were cemented with CR inlay cement. Dye(2% methylene blue) penetration and adhesion pattern were evaluated after sectioning of gingival margin into :3 pieces. The results were as follows ; 1. The thickness of resin cement showed unevenchanging pattern with that of die spacer, namely, it was increased until 4 times' application of Nice-Fit but was decreased with 6 times' application of that. 2. The degree of dye penetration wasn't affected by cement thickness within a limited value. 3. Most of dye penetration was shown through the interface between cement and enamel rather than the interface between cement and CR inlay. This shows that the affinity of resin cement for CR inlay was superior to the adhesive strength with tooth structure. 4. No gap was found at the interface between enamel and cement but some showed separation between dentin and cement. It is concidered that the contraction force of cement was less than the bond strength with the enamel. 5. Lots of voids were found in the CR inlay and resin cement. There was a pooling tendency of bonding agent and cement in the axiogingival line angle portion. 6. In some specimens, cracks were shown in enamel margin. From this it could be considered that cavity preparation and surface treatment weakened the tooth structure.

• Transactions of Materials Processing
• /
• v.31 no.1
• /
• pp.5-10
• /
• 2022

In multi-stage cold forging process, to enhance the productivity and product quality, in-site process monitoring technique by implanting sensors such as piezo-sensor and acoustic emission sensor has been continuously studied. For accurate analysis of the process, the selection of appropriate sensors and implantation positions are very important. Until now, in a multi-state forging machine, wedge parts located at the end of punch-set are used but it is difficult to analyze minute changes in die block-set. In this study, we also implanted sensors to the die part (die spacer) and compared signals from both sensors and found that sensing signals from die part showed enhanced process monitoring results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.10
• /
• pp.1019-1025
• /
• 1991

An analytic method of computation of the coupling coefficients between a microstripline and a die-lectric resonator is showen in this paper. The relationships among the substrate material, the ground plane, the diele-lents. The theoretically computed values of Qext are compared with the experimentally measured values of Qext in there is no dieletric spacer between them, As a result, the reflection coefficients with the dielectric spacer between the dieletric resonator and the substrate are decreased more than the reflection coefficients without the didlectric spacer between them.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.9-13
• /
• 1999

In order to investigate the effect of flange wrinkling on the wall break of a deep drawn rectangular cup, experiments and simulation were done. The effect of the wrinkling height on drawing force and wall break for a moving blank holder system with spacer were studied by setting a fixed clearance between the drawing die and the blank holder. Simulation and experimental results showed that wall break could be provoked by the flange wrinkling. As the wrinkling height increased, the punch force grew. The maximum punch force was obtained at its final stage of stroke.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.2
• /
• pp.29-33
• /
• 2012

The demand for 3D wafer level integration has been increasing significantly. Although many technical challenges of wafer stacking are still remaining, wafer stacking is a key technology for 3D integration due to a high volume manufacturing, smaller package size, low cost, and no need for known good die. Among several new process techniques Cu-to-Cu wafer bonding is the key process to be optimized for the high density and high performance IC manufacturing. In this study two main challenges for Cu-to-Cu wafer bonding were evaluated: misalignment and bond quality of bonded wafers. It is demonstrated that the misalignment in a bonded wafer was mainly due to a physical movement of spacer removal step and the bond quality was significantly dependent on Cu bump dishing and oxide erosion by Cu CMP.

• The Plant Pathology Journal
• /
• v.38 no.2
• /
• pp.131-145
• /
• 2022

Ceratocystis wilt disease has caused significant mortality in duku (Lansium domesticum) since 2014 and has now spread to all districts in South Sumatra, Indonesia. Recently, 16 isolates from duku representing populations from various districts in South Sumatra were isolated. Analysis for the morphological characteristic of the isolate showed that the population has a uniform morphology. Genetic analysis based on internal transcribed spacer (ITS) and β-tubulin sequences verified that the population has being dominated by the ITS5 haplotype of Ceratocystis fimbriata and a new ITS group, the ITS7b haplotype that was localized in Musi Banyuasin. Both haplotypes were highly pathogenic to duku. Inoculation tests on various forest and agroforestry plant hosts showed that both haplotypes were highly pathogenic to Acacia mangium, moderately pathogenic to Acacia carsicarpa, Eucalyptus urophylla, and Melaleuca cajuputi, but weakly pathogenic to Dyera costulata, Hevea brasiliensis, and Alstonia scholaris. Therefore, this pathogen becomes a serious threat to Indonesia's biodiversity due to its ability to infect forest and agroforestry plants, especially the indigenous ones.