• Design & Manufacturing
• /
• v.12 no.1
• /
• pp.36-40
• /
• 2018

The car requires an inside mirror installed between the driver's seat and the passenger's seat to ensure the driver's rear and side view of the driver. Inside mirrors must always be attached to the vehicle to ensure the driver's visibility. Inside mirrors attached to the windshield of a vehicle are always exposed to direct sunlight and should be semi-permanently usable in hot and humid summer weather in Korea. Therefore, the mirror mount, which is the junction of the inside mirror, is particularly important in corrosion resistance and wear resistance suitable for humidity. Mirror mounts are currently difficult to manufacture due to their reliance on powder molding technology in advanced countries such as Japan and Germany. This paper focuses on the fabrication of high corrosion resistant stainless mirror mounts by vacuum sintering technique and focuses on the selection of materials suitable for the production of mirror mounts through experiments of 300 series stainless steel and 400 series stainless steel manufactured by vacuum sintering.

• Design & Manufacturing
• /
• v.6 no.2
• /
• pp.79-83
• /
• 2012

Inner part is used as an insulator in wire fuses. After injection molding, inner part has been showed flashes, filling defects and deformation. After production, operators have to cut off flashes, one by one. this process leads to continuous low productivity and loss of source materials. This study focuses on identifying the causes for flashes, filling defects, clamping force of injectors, mold adhesion, resin of liquidity and others, and on resolving those issues.

• Design & Manufacturing
• /
• v.1 no.1
• /
• pp.13-16
• /
• 2007

Almost all injection molds have multi-cavity runner system for mass production, which are designed with geometrically balanced runner system in order to accomplish filling balance between cavity to cavity during processing. However, even though geometrically balanced runner is used, filling imbalance have been observed. Filling imbalance could be decreased by modifying processing conditions such as injections rate, mold temperature, injection pressure, melt temperature that are related to shear, viscosity. In this study, a series of experiment was conducted to investigate filling imbalance variation when modifying runner layout and polymer and to determine which processing condition influences as the primary cause of filling imbalance in geometrically balanced runner system.

• Journal of Korea Foundry Society
• /
• v.33 no.5
• /
• pp.204-209
• /
• 2013

The family mold casting have advantages which are able to make products with different shapes and dimensions simultaneously in a single mold. In this study, the design of the 4 cavity rotor family mold was used by "Anycasting" software, the defects occurred during die casting were predicted and suggested the best optimization conditions for sound products. The result of the experiment were that the optimum overflow design was needed for gas emission and control of residual oxides. It was clear that the defects positions formed by diecasting were agreed with nearly them predicted by simulation.

• Design & Manufacturing
• /
• v.2 no.5
• /
• pp.25-29
• /
• 2008

Almost all injection molds have multi-cavity runner system for mass production, which are designed with geometrically balanced runner system in order to accomplish filling balance between cavity to cavity during processing. However, even though geometrically balanced runner is used, filling imbalance have been observed. Filling imbalance could be decreased by modifying processing conditions such as injections rate, mold temperature, injection pressure, melt temperature that are related to shear, viscosity. In this study, a series of experiment was conducted to investigate filling imbalance variation when modifying runner layout and ploymer and to determine which processing condition influences as the primary cause of filling imbalance in geometrically balanced runner system. The filling imbalance was desreased up to result range of $3{\leq}DFI{\leq}8(%)$ by using a new runner system for balanced filling.

• Design & Manufacturing
• /
• v.6 no.2
• /
• pp.42-47
• /
• 2012

The paper deals with an analysis of an extrusion process with a divided material flow in a combined radial - backward extrusion. We have discussed the influences of tool geometry such as punch nose angle, relative gap height, die corner radius on material flow and surface expansion into can and flange region. To analyse the process, numerical simulations by the FEM and experiment by physical modeling using Al alloy as a model material have been performed. Based on the results, the influence of fixed parameters on the distribution of divided material flow and surface expansion are obtained.

• Design & Manufacturing
• /
• v.13 no.3
• /
• pp.29-34
• /
• 2019

Cell phone injection is characterized by its small size and thinness. In addition, the product has a short cycle time, requiring a very short production schedule. To produce more accurate products faster, data from experience in producing similar products is required. In this study, two mobile phone models are presented. In this study, the quality problems caused by molding analysis and actual injection molding were analyzed and made into a database. As a result, it was considered that all the defects in the molding analysis do not affect the product in some cases, rather than appear as defects in the actual product. All defects shown in the molding analysis can be made into a database, and based on this data, it will be possible to obtain an effect that can predict more accurately whether it will cause problems after injection.

• Design & Manufacturing
• /
• v.11 no.2
• /
• pp.9-14
• /
• 2017

The design and manufacturing tehcnology of IC sockets beyond 0.3mm pitch were presented. We compared the developed IC socket with the conventional one especially on the core metal-insulation part. Advanced machining techniques were employed to provide high precision. Our wire electrodischarge machining and high speed machining centers were able to maintain the micro-scale precision. We performed an injection molding analysis using a commercial analysis tool to predict the performance of the developed IC socket. We found that the solidification of the plastic resin and the high level of the clamping force are responsible for the defects such as incomplete filling and short shot. From these results, we modified the IC socket and successfully remove the defects. We were also able to find out that the new design socket needs less maintenance cost.

• Korean Journal of Computational Design and Engineering
• /
• v.10 no.6
• /
• pp.381-391
• /
• 2005

The design methodology of injection molding die has been changed from two-dimensional drafting to three-dimensional solid modeling, which is due to many advantages over the conventional methodology in terms of design modification and data associativity. In addition to the solid modeling capability, it is required for a mold designer to utilize a database management system that facilitates efficient mold design. In the paper presented is the implementation of a software program which automatically generates three-dimensional mold-bases including standard parts and slider parts, conforming to given geometric constraints. It is based on a commercial CAD system (Unigraphics NX) along with related API (application program interface) libraries. The research is expected to reduce design efforts and simplify construction of a complex three-dimensional mold-base model that is comprised of standard parts and slider parts, by use of the three-dimensional database and automatized geometric dimensioning.

• Design & Manufacturing
• /
• v.9 no.2
• /
• pp.30-33
• /
• 2015

In injection molding, many kinds of defects have occurred because of a characteristic of plastics injection molding. Weld line is one of the defects is formed when separated melt fronts recombine together during the mold filling stage. That is one of problems in injection molding. Weld lines in the appearance of plastics parts can deteriorate visible quality. And most importantly, the local mechanical strength in the weld line area can be significantly weaker. It could be one of the most problems for structural applications. In this study, the mold available two-shot-molding of same polymers have been designed, and a series of experiment about tensile strength in weld line area has been conducted using Taguchi's design of experiment to optimize injection molding conditions decreasing of weld strength and find out a factors affected weld strength in two-shot- molding.