• Journal of Korean Association for Spatial Structures
• /
• v.12 no.4
• /
• pp.81-90
• /
• 2012

The concrete-filled tube (CFT) column has the excellent structural performance. But it is difficult to connect with column and beam because of closed section. Its Solution, 2 members of ㄷchennel in which Internal diaphragm is installed were welded beforehand and the method of making Rectangular Steel Tube was proposed. According to upside and downside junction shape, Internal diaphragm suggested as symmetric specimen and asymmetric specimen. The upper and lower diaphragm of the Symmetric specimen used the same horizontal and The upper diaphragm of the Asymmetric specimen used the horizontal plate and the lower diaphragm used the vertically plate. In this research, 4 T-shape column to beam steps connections were tested with cyclic loading experiment in order to evaluate the structural capability of the offered connection. Symmetric specimens be a failure in 0.03rad from beam flange. And Asymmetric specimens be a failure in 0.05rad from column interface. The comparison results of All specimens shown similar to energy absorption capacity in 0.02rad.

• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.35T no.1
• /
• pp.75-81
• /
• 1998

This paper is to optimize single-element piezoresistor shear stress strain gauge related to aspect ratio of rectangular diaphragm. The shear stress distribution on diaphragm has been simulated by finite-element method(FEM). As simulation results, the maximum sensitivity for strain gauge was appeared at the center of diaphragm with aspect ratio 3, and in along to long edge with the ratio 2. The diaphragm with ratio 2 is not acceptable due to the yield of mask alignment in IC process technology. The optimum condition of diaphragm with respect to good sensitivity was realized in the case of ratio 3. In this case, the area by gauge was 8% of overall size of rectangular diaphragm.

• Steel and Composite Structures
• /
• v.20 no.1
• /
• pp.1-20
• /
• 2016

The strength and stiffness of the steel beams to concrete-filled tubular columns connections are significantly reduced if the thick-walled components are used. However, the thick-walled tubes used for columns can largely reduce the demand for space and increase the strength-to-weight ratio. This paper describes the cyclic performance of extended through-diaphragm connections between steel beams and thick-walled concrete-filled tubular columns improved with fillets around the diaphragm corners. Test on one full-scale connection was conducted to assess the seismic behavior of the connection in terms of strength, stiffness, ductility, deformation, energy dissipation, and strain distribution. It is shown that the fillets and extended through-diaphragm can alleviate the stress concentration in the connection and thus improve the seismic performance. The test results demonstrate that the through-diaphragm connections with thick-walled concrete-filled tubular columns can offer sufficient energy dissipation capacity and ductility appropriate for its potential application in seismic design.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.6
• /
• pp.1-10
• /
• 2013

In this paper, the main cause on excitation of the combustion instability which may occur in the hybrid rocket motor with a diaphragm was studied. Hybrid rocket motor propulsion tests considering various experimental conditions such as with a diaphragm or not, a diameter of diaphragm, oxidizer mass flow rate, fuel length, etc were performed, and the combustion visualization for the inside of a hybrid rocket motor with a diaphragm was performed. With these experimental results, it was confirmed that the main cause of a large excitation was the hole-tone, and it was shown that the hole-tone model can be predicted experimental primary pressure oscillation frequency quite well.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.327-327
• /
• 2007

This paper reports the simulation results of piezoelectric microspeakers due to structural changes(diaphragm materials, corrugation width and electrode shapes). When we compared the dependence of diaphragm material properties, the microspeaker with LTO(Low Temperature Oxide) diaphragm shows higher deflection than that of silicon nitride diaphragm, even though the resonant frequencies are almost same in both cases. In case of circular-electrode microspeaker, the deflection of diaphragm is about $16\;{\mu}m$ at 20 V, and it decreases as the corrugation width is decreased. However, the deflection of diaphragm with the square-electrode reveals almost twice times higher value at the same applied voltage than the circular one, and it increases as the corrugation depths are decreased from $30\;{\mu}m\;to\;10\;{\mu}m$. The first resonant frequency of microspeakers present about 1.8 kHz in circular-electrode and 1.2 kHz in square-electrode, respectively.

• New & Renewable Energy
• /
• v.8 no.3
• /
• pp.6-13
• /
• 2012

This paper describes unsteady internal flow characteristics of a cathode air blower, used for the 1 kW fuel cell system. The cathode air blower considered in the present study is a diaphragm type blower. To analyze the flow field inside the diaphragm cavity, compressible unsteady numerical simulation is performed. Moving mesh system is applied to the numerical analysis for describing the volume change of the diaphragm cavity in time. Throughout a numerical simulation by modeling the inlet and outlet valves in a diaphragm cavity, unsteady nature of an internal flow is successfully analyzed. Variations of mass flow rate, force and pressure on the lower moving plate of a diaphragm cavity are evaluated in time. The computed mass flow rate at the same pressure and rotating frequency of a motor has a maximum of 5 percent error with the experimental data. It is found that flow pattern at the suction process is more complex compared to that at the discharge process. Unsteady nature of internal flow in the cathode air blower is analyzed in detail.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.258-262
• /
• 2011

The hybrid combustion experiments using non-combustible diaphragm were performed for characteristic of regression rate and combustion efficiency. Results of experiments using diaphragm were showed that the regression rate and efficiency were increased. In addition, the larger difference between fuel grain port and diaphragm port increase the regression rate and efficiency. The modified regression rate equation was proposed with the port area ratio of fuel and diaphragm.

• Journal of Sensor Science and Technology
• /
• v.28 no.1
• /
• pp.58-63
• /
• 2019

This research aims at designing a diaphragm made of SUS316L stainless steel for ultra high pressure sensors and evaluating its performance with a PZT driven deformation tester instead of high pressure chamber testing up to 100 MPa. Finite element method analysis indicates that the optimum thickness of a flat diaphragm is 1.5 mm not only to secure safety of sensors up to 100 MPa but also to enhance displacement measuring sensitivity. For this thickness, the maximum displacement at the center of the diaphragm is $5.3{\mu}m$. The PZT actuator must offer a force of 1,669 N to create a pressure of 100 MPa at the diaphragm surface in order to obtain a displacement of $5.3{\mu}m$. The performance evaluation by the PZT driven tester demonstrates nearly the same results as the same results as the sensors tested in the ultra high pressure chamber.

• Tribology and Lubricants
• /
• v.39 no.5
• /
• pp.212-215
• /
• 2023

Diaphragm compressors play a crucial role in safely compressing large volumes of high-purity hydrogen gas without contamination or leakage, thereby ensuring quality and reliability. Diaphragm compressors use a thin, flat, triple-layered diaphragm plate that is subjected to repetitive piston pressure for compression. They are usually made of metallic materials such as stainless steel or Inconel owing to their high-pressure resistance. However, since they are consumable components, they fail due to fatigue from repetitive pressure and vibration stress. This study aims to evaluate the scratch characteristics of diaphragms in operational environments by conducting tests on three different samples: Inconel 718, AISI 301, and Teflon-coated AISI 301. The Inconel 718 sample underwent a polishing process, the AISI 301 sample used raw material, and the Teflon coating was applied to the AISI 301 substrate at a thickness of 50 ㎛. To assess the scratch resistance, reciprocating motion friction tests were performed using a tribometer, utilizing 220 and 2000 grit sandpapers as the counter materials. The results of the friction tests suggested that the Teflon-coated sample exhibited the lowest initial friction coefficient and consistently maintained the lowest average friction coefficient (0.13 and 0.11 with 220 and 2000 grit, respectively) throughout the test. Moreover, the Teflon-coated diaphragm showed minimal wear patterns, indicating superior scratch resistance than the Inconel 718 and AISI 301 samples. These findings suggest that Teflon coatings may offer an effective solution for enhancing scratch resistance in diaphragms, thereby improving compressor performance in high-pressure hydrogen applications.

• Journal of Chest Surgery
• /
• v.35 no.10
• /
• pp.730-735
• /
• 2002

Diaphragm is innervated by phrenic nerve and lower intercostal nerves. For patients with avulsion injury of brachial plexus, an in situ graft of phrenic nerve is frequently used to neurotize a branch of the brachial plexus. We studied short-term and mid-term changes of diaphragmatic level and movement in patients with dissection of phrenic nerve for neurotization. Material and Method : Thirteen patients with division of either-side phrenic nerve for neurotization of musculocutaneous nerve were included in this study. With endoscopic surgical procedure, the intrathoracic phrenic nerve was entirely dissected and divided just above the diaphragm. The dissected phrenic nerve was taken out through thoracic inlet and neck wound and then anastomosed to the musculocutaneous nerve through a subcutaneous tunnel. With chest films and fluoroscopy, levels and movements of diaphragm were measured before and after operation. Result : There was no specific technical difficulty or even minor postoperative complications following endoscopic division of phrenic nerve. After division of phrenic nerve, diaphragm was soon elevated about 1.7 intercostal spaces compared with the preoperative level, but it did not show paradoxical motion in fluoroscopy. More than 1.5 months later, diaphragm returned downward close to the preoperative level (average level difference was 0.9 intercostal spaces; p＝NS). Movement of diaphragm was not significantly decreased compared with the preoperative one. Conclusion : After division of phrenic nerve, the affected diaphragm did not show a significant decrease in movement, and the elevated diaphragm returned downward with time. However, the decreased lung volumes in the last spirometry suggest the decreased inspiratory force following partial paralysis of diaphragm.