• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2005년도 학술발표회 논문집
• /
• pp.324-330
• /
• 2005

The flexural strength and ductility capacity of reinforced concrete columns are largely dependent on the amount of transverse steel. However, current design code does not specify the confinement effect of transverse steels in strength calculation. A non-linear moment-curvature analysis of RC column sections was conducted in order to develop PM interaction diagram considering transverse reinforcement effects. In this paper, a more reasonable application method of PM interaction diagram considering transverse steel amounts is introduced and proposed, based on moment-curvature non-linear analysis. Also, we proposed simplified method to use. easily in practical design.

• International Journal of Precision Engineering and Manufacturing
• /
• 제7권2호
• /
• pp.36-40
• /
• 2006

Diagnosis and repair tasks of an unbalanced rigid rotor reduce the chances of unexpected failure and the consequent losses in production, time, and money. This paper presents investigation of a balancing system for equilibration of rigid rotor unbalance. A practical vibration signal based method is developed for unbalance diagnosis using wavelet technology and a Lissajous diagram. This paper shows that a mass unbalance can be efficiently estimated through an appropriate narrow-band filter used to extract the required spectra component. The wavelet technology is used to design specified narrow filter bank. A modified Lissajous diagram is also introduced with statistical analysis to compute the phase position. Several experimental tests demonstrate the effectiveness in balancing the mass unbalance of a rigid rotor.

• 소성∙가공
• /
• 제26권3호
• /
• pp.144-149
• /
• 2017

In order to characterize the macroscopic mechanical response of ultra-thin (0.1 mm thick) ferritic stainless steel sheet at various loading paths, a crystal plasticity finite element method (CP-FEM) was introduced. The accuracy of the prediction results was validated by comparing with the experimental data. Based on the results, the forming limit diagram (FLD) was predicted using a modified Marchinicak-Kuczinski model coupled to a non-quadratic anisotropic yield function, namely, Yld2000-2d. The predicted FLD was found to be in good agreement with the experimental data.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.438-441
• /
• 2006

Since the behavior of structural members subjected to blast load shows different responses, the effect of impulse as well as peak load should be considered in the damage analysis. The threshold on P-I diagram that causes specific damage level divides the diagram into the failure zone and the non-failure zones. In this study, numerical analysis is performed based on single-degree-of-freedom (SDOF) techniques to generate rational P-I diagram considering material non-linearity and dual failure modes (flexure and direct shear) of RC beams. From the comparison with existing test results it is concluded that proposed numerical method is good to derive failure mode of RC beam under blast load.

• Journal of Welding and Joining
• /
• 제19권5호
• /
• pp.466-473
• /
• 2001

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 추계학술대회 논문집
• /
• pp.797-803
• /
• 2009

The accurate prediction of dynamic characteristics of high speed rotors, such as gas turbines, is important to avoid the possibility of operating the machinery near the critical speeds or unstable speed regions. However, the dynamic analysis methods and softwares for gas turbines have been developed in the process of producing many gas turbines by manufacturers and most of them have seldom been disclosed to the public. Recently, commercial FEM softwares, such as SAMCEF, ANSYS and NASTRAN, started supporting some rotordynamics analysis modules based on 3-D finite elements. In this paper, the dynamic analysis method using commercial S/W, especially ANSYS, is attempted for the small-size gas turbine engine rotor, and the analysis capability and limitations of its rotordyamics module are evaluated for further improvement of the module. As the preliminary procedure, the rotordyamic analysis capability of ANSYS was tested and evaluated with the reference models of the well-known dynamics. The limitations in application of the rotordynamics module were then identified. Under the current capability and limitations of ANSYS, it is shown that Lee diagram, a new frequency-speed diagram enhanced with the concept of $H{\infty}$ in rotating machinery, can be indirectly obtained from FRFs computed from harmonic response analysis of ANSYS. Finally, it is demonstrated based on the modeling and analysis method developed in the process of the S/W verification that the conventional Campbell diagram, Lee diagram, mode shapes and critical speeds of the small-size gas turbine engine rotor can be computed using the ANSYS rotordynamics module.

• 한국소음진동공학회논문집
• /
• 제20권1호
• /
• pp.36-44
• /
• 2010

The accurate prediction of dynamic characteristics of high speed rotors, such as gas turbines, is important to avoid the possibility of operating the machinery near the critical speeds or unstable speed regions. However, the dynamic analysis methods and softwares for gas turbines have been developed in the process of producing many gas turbines by manufacturers and most of them have seldom been disclosed to the public. Recently, commercial FEM softwares, such as SAMCEF, ANSYS and NASTRAN, started supporting some rotordynamics analysis modules based on 3-D finite elements. In this paper, the dynamic analysis method using commercial S/W, especially ANSYS, is attempted for the small-size gas turbine engine rotor, and the analysis capability and limitations of its rotordyamics module are evaluated for further improvement of the module. As the preliminary procedure, the rotordyamic analysis capability of ANSYS was tested and evaluated with the reference models of the well-known dynamics. The limitations in application of the rotordynamics module were then identified. Under the current capability and limitations of ANSYS, it is shown that Lee diagram, a new frequency-speed diagram enhanced with the concept of $H{\infty}$ in rotating machinery, can be indirectly obtained from FRFs computed from harmonic response analysis of ANSYS. Finally, it is demonstrated based on the modeling and analysis method developed in the process of the S/W verification that the conventional Campbell diagram, Lee diagram, mode shapes and critical speeds of the small-size gas turbine engine rotor can be computed using the ANSYS rotordynamics module.

• 한국전산구조공학회논문집
• /
• 제18권2호
• /
• pp.103-111
• /
• 2005

본 논문에서는 수치적분 정도를 향상시킬 수 있는 새로운 무요소 기법을 제안한파 저자들에 의해 페트로프-갤러킨 자연요소법(PG-NEM)이라 명명된 이 새로운 기법은 보로노이 다이어그램과 델라우니 삼각화에 기반을 두고 있으며, 이는 BG-NEM이라 불리는 기존의 자연요소법과 개념적으로 동일하다. 하지만, 동일한 시험 형상함수와 시도 형상함수를 선택하는 BG-NEM과는 달리, PG-NEM에서는 지지영역이 적분을 위한 배경격자에 정확하게 일치하도록 시험 형상함수를 독립적으로 선택하는 페트로프-갤러킨 개념에 기반을 두고 있다. 따라서, 제안된 기법은 BG-NEM과 비교하여 수치적분 정도를 현저히 향상시킬 것으로 기대된다.

• 한국지능정보시스템학회:학술대회논문집
• /
• 한국지능정보시스템학회 2001년도 The Pacific Aisan Confrence On Intelligent Systems 2001
• /
• pp.211-218
• /
• 2001

This paper introduces a method of constructing expert systems in an integrated environment for automatic software design. This integrated environment may be applicable from top-level system architecture design, data flow diagram design down to flow chart and coding. The system is integrated with three CASE tools, FSD (Functional Structure Diagram), DFD (Data Flow Diagram) and structured chart PAD (Problem Analysis Diagram), and respective expert systems with automatic design capability by reusing past design. The construction way of these expert systems is based on systematic acquisition of design knowledge stemmed from a systematic design work process of well-matured developers. The design knowledge is automatically acquired from respective documents and stored in the respective knowledge bases. By reusing it, a similar software system may be designed automatically. In order to develop these expert systems in a short period, these design knowledge is expressed by the unified frame structure, functions of th expert system units are partitioned mono-functions and then standardized components. As a result, the design cost of an expert system can be reduced to standard work procedures. Another feature of this paper is to introduce the integrated environment for automatic software design. This system features an essentially zero start-up cost for automatic design resulting in substantial saving of design man-hours in the resulting in substantial saving of design man-hours in the design life cycle, and the expected increase in software productivity after enough design experiences are accumulated.

• 한국실내디자인학회논문집
• /
• 제20권1호
• /
• pp.89-97
• /
• 2011

Furniture design is no exception to human desire for pursuit of the nature. In various design fields, it has turned out nature-decorative method in the past, and also recently it has turned out bio-adaptive method which is more root design process using principal of generation in nature world. The purpose of this study is to analyze application methods and characteristics of fractal geometry and voronoi diagram which are most representative principals of generative design in nature by research on the example of furniture design using these principals. The results of having analyzed fumitures by generative design can be summarized as follows; design principals of fractal; superposition, scaling, repetition & gradation, deformation, distortion and voronoi diagram; individual speciation, variational patten, repetition gradation, ambiguous boundary create new design concept and emergent form in furniture design. Application methods are 'form emergence by algorithm', 'conventional process based on principals of generative design', and 'reproduction of pattern from generative design'. Biological reinterpretations and new explorations of principals of nature generation offer unbounded possibilities for furniture design.