• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.201-204
• /
• 2001

In this paper, for modeling of electrical characteristics in Poly Silicon Thin Film Transistors with process parameters set up optimum values. So, the I-V characteristics of poly silicon TFT parameters are examined and simulated in terms of the variations in process parameter. And these results compared and analyzed simulation values with examination value. The simulation program for characteristic analysis used SUPREM IV for processing, Matlab for modeling by mathematics, and SPICE for electric characteristic of devices. Input parameter for simulation characteristics is like condition of device process sequence, these electric characteristic of I$_{D}$-V$_{D}$, I$_{D}$-V$_{G}$, variations of grain size. The Gate oxide thickness of poly silicon are showed similar results between real device characteristics and simulation characteristics.ristics.

• Proceeding of EDISON Challenge
• /
• 2013.04a
• /
• pp.266-268
• /
• 2013

In this paper, we study the channel doping concentration characteristics of junctionless nanowire transistors (JLT) using Edison nanowire FET device simulation. JLT has no junctions by very simple fabrication process. And this device has less variability and better electrical properties than classical inversion-mode transistors with PN junctions at the source and drain. In this simulation we use tri-gate structure. Source and drain doping concentration is $10^{20}atoms/cm^3$. The simulation results show that I-V characteristics of JLT change due to the variation of channel doping concentration.

• Elastomers and Composites
• /
• v.53 no.4
• /
• pp.226-233
• /
• 2018

Elastomers based on the thermoplastics are widely used in rubber industries. Thermoplastic elastomers have the advantages of an easy shaping process and elimination of recycling problems. Thermoplastic polyester elastomer (TPE) is used for making rubber bands in wearable devices and its applications are increasing. In this study, five wrist bands were designed and their mechanical behaviors were examined by computer simulation, using hyper elastic models, Mooney-Rivlin and Ogden models, and a linear elastic model. Simulation results were compared and discussed in terms of band design and material model.

• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1309-1313
• /
• 2019

In this paper, the electrical characteristics of Gate grounded NMOS(GGNMOS), Lateral insulated gate bipolar transistor(LIGBT), Silicon Controlled Rectifier(SCR), and Proposed ESD protection device were compared and analyzed. First, the trigger voltage and holding voltage were verified by simulating the I-V characteristic curve for each device. After that, the robustness was confirmed by HBM 4k simulation for each device. As a result of HBM 4k simulation, the maximum temperature of the proposed ESD protection device is lower than that of GGNMOS and GGLIGBT and SCR, which means that the robustness is improved, which means that the ESD protection device is excellent in terms of reliability.

• Agricultural and Biosystems Engineering
• /
• v.5 no.2
• /
• pp.45-49
• /
• 2004

Objective of the study was to develop a garlic clove metering device. The metering device consisted of a drum, a bucket and a bucket cover. A garlic clove simulator was designed to simulate motions of garlic cloves in the metering device. Simulation was performed using a multibody dynamic analysis program, RecurDyn version 5.1. Physical properties of garlic cloves such as mass and center of gravity were determined using 3D CAD modeler, IDEAS version 10.0. In order to compare the results of the simulation with actual movement of a garlic, movement of garlic clove was photographed by a high speed camera. A prototype metering device was built and tested under various metering speeds and metering guide angles. At the 12 rpm metering speed, rate of single-clove-discharge was $90.0\%$ and missing rate $1.3\%$ at $5^{\circ}$.

• Land and Housing Review
• /
• v.10 no.2
• /
• pp.53-58
• /
• 2019

Particulate matter (PM) is designated as a group 1 carcinogen by the International Agency for Research on Cancer (IARC) of the World Health Organization (WHO). In South Korea, the health threat caused by PM is the most serious level internationally. Therefore, in order to solve the urban PM problem, it is important to develop the technology that can control PM efficiently. In this study, CFD(Computational Fluid Dynamics) simulation was performed for PM pre-filter (type 1-3 with different PM collecting room) to develop a high-efficiency PM collecting device. The complex flow field and the local flow phenomenon inside the PM collecting device were understood with CFD simulation by changing the shape and size of the pre-filter. The PM removal performance can be described with flow rate through the device and PM removal efficiency. The type-1 pre-filter with 5x5 size collecting room was confirmed to have the highest efficiency. Based on the analysis results, the optimal type of pre-filter could be developed and it would be applied as an element technology included in the PM collecting device.

• Journal of Drive and Control
• /
• v.12 no.3
• /
• pp.11-17
• /
• 2015

An intelligent deburring control (IDC) device is used to control the constant force for a deburring tool mounted on the end-effector of a robotic arm. This device maintains a constant contact force between the deburring tool and the workpiece in order to provide a good deburring performance. In this paper, we build a mathematical model in Matlab/Simulink to estimate the force control mechanism of the pneumatic system for the IDC device. The Simulink blocks are built for each separate part and are linked into an integrated simulation system. Such a model also relies on the effects of the flow rate through the valve, air compressibility in the cylinder, and time delay in the pressure valve. The results of the simulation are compared to a simple experiment in which convenient math modeling is performed. These results are then used to optimize the mechanical design and to develop a force control algorithm for the pneumatic cylinder.

• Journal of the Korean Solar Energy Society
• /
• v.35 no.1
• /
• pp.1-8
• /
• 2015

In the present study, the effects of the heat spreader thickness and the heat sink size on the thermal performance of a cooling device for a concentrating photovoltaic (CPV) module were numerically investigated. Numerical simulation was conducted by using the simulation tool ICEPAK, commercial software based on the finite volume method. Numerical results were validated by comparing the existing experimental data. The thermal performance of a cooling device, which consisted of a heat spreader and a natural convective heat sink, was evaluated with varying the heat spreader thickness and the heat sink size. The geometric configuration of the natural convective heat sink, such as the fin height, the fin spacing, and the fin thickness, was optimized by using the existing correlation. The numerical results showed that the thermal performance of the cooling device increased as the heat spreader thickness or the heat sink size increased. Also, it was found that the spreading thermal resistance plays an important role in the thermal performance of the cooling device which has the localized heat source.

• Korean Journal of Computational Design and Engineering
• /
• v.14 no.6
• /
• pp.415-423
• /
• 2009

Because of the fast changing car design and increasing facilities, manufacturing process of cars is getting more complex now a days. Particularly, car manufacturing system that consist of automated devices, applies various simulation techniques to validate device motion and detect collision. To cope with this problem, traditional manufacturing system deployed test-run with the real devices. However, increased computing power in a contemporary manufacturing system changes it into realistic 3D simulation environment. Similarly, managed device data that was generated using 2D traditionally, can be converted to 3D realistic simulation. The existing problem with 3D simulation is disjoint data interaction between different work stations. Consequently, JIGs, fixing the car part accurately, are changed according to fixing position on the part or a part shape properties. In practice, the 3D JIG data has to be managed according to kinematic information, but not of its features. However, generating kinematic information to the 3D model repeatedly according to frequent change in part is not explained in current literatures. To fill this knowledge gap, this paper suggests an improving method of rendering 3D JIG kinematics information to simulation model. Thereafter, it shows the result of implementation.

• Journal of Radiation Protection and Research
• /
• v.49 no.1
• /
• pp.29-39
• /
• 2024

Background: The gamma emission tomography (GET) device has been reported a reliable technique to inspect partial defects within spent nuclear fuel (SNF) of pin-by-pin level. However, the existing GET devices have low accuracy owing to the high attenuation and scatter probability for SNF inspection condition. The purpose of this study is to design and optimize a Yonsei single-photon emission computed tomography version 2 (YSECT.v.2) for fast inspection of SNF in water storage by acquisition of high-quality tomographic images. Materials and Methods: Using Geant4 (Geant4 Collaboration) and DETECT-2000 (Glenn F. Knoll et al.) Monte Carlo simulation, the geometrical structure of the proposed device was determined and its performance was evaluated for the ¹³⁷Cs source in water. In a Geant4-based assessment, proposed device was compared with the International Atomic Energy Agency (IAEA)-authenticated device for the quality of tomographic images obtained for 12 fuel sources in a 14 × 14 Westinghouse-type fuel assembly. Results and Discussion: According to the results, the length, slit width, and septal width of the collimator were determined to be 65, 2.1, and 1.5 mm, respectively, and the material and length of the trapezoidal-shaped scintillator were determined to be gadolinium aluminum gallium garnet and 45 mm, respectively. Based on the results of performance comparison between the YSECT.v.2 and IAEA's device, the proposed device showed 200 times higher performance in gamma-detection sensitivity and similar source discrimination probability. Conclusion: In this study, we optimally designed the GET device for improving the SNF inspection accuracy and evaluated its performance. Our results show that the YSECT.v.2 device could be employed for SNF inspection.