• 제어로봇시스템학회:학술대회논문집
• /
• 1999.10a
• /
• pp.108-111
• /
• 1999

In this paper, we develope a composite control law for linear systems with norm-bounded time-varying parameter uncertainties, which consists of a basic linear robust control do-signed so as to generate a desired transient time-response for the worst-case parameter variation and a nonlinear modification term designed so as to reduce cautiousness of the linear robust control in an adaptive manner. The proposed controller is established such that the reduction of cautiousness of the linear robust control is well incorporated into the achievement of a good transient behavior.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.380-384
• /
• 1992

The position control of a pneumatic cylinder suing low cost on-off valves is studied. The valve control band(VCB) was proposed toget fast response and toprevent solenoid valves from unnecessary switching at the beginning of response. A learning algorithm was used to compensate the nonlinearity and complexity in mathematical modelling of pheumatic on-off controlled positioning systems. In this algorithm, the desired performance index and modified learning rate, were proposed to improvespeed and convergence of learning control. It is shown experimentally that the proposed algorithm is robust to changes of system parameters: the setting time less than 1.0 sec and the error bound of .+-. 0.1 mm can be obtained. The effects of supply pressure, size of switching valves and the effect of multiple valves are discussed, and computer simulation onthe dynamic performances of the pneumatic system is also presented.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10b
• /
• pp.370-375
• /
• 1987

Damping piston with an orifice in the piston head is utilized to improve the damping characteristics of a pneumatic push-push type rotary actuator. Through linearized analysis, the optimum size of orifice, which gives maximum damping effect at the frequency where damping is desired. most, is predicted. The frequency response test of teal system were carried out to see the effects of damping piston and to obtain true optimum size of orifice by trying orifices of various size near the predicted value. During the tests, both air and helium were tried as working fluid, and a lag-lead compensation circuit was incorporated to improve system dynamics. The finally chosen orifice size is a little bigger than that predicted from analysis, however it gives high damping effects for the finally designed pneumatic system enough to have wide frequency response bandwidth.

• Earthquakes and Structures
• /
• v.4 no.5
• /
• pp.509-525
• /
• 2013

In this paper, learning capabilities of two types of Arterial Neural Networks, namely hierarchical neural networks and Generalized Regression Neural Network were used in a two-stage approach to develop a method for generating spatial varying accelerograms from acceleration response spectra and a distance parameter in which generated accelerogram is desired. Data collected from closely spaced arrays of seismographs in SMART-1 array were used to train neural networks. The generated accelerograms from the proposed method can be used for multiple support excitations analysis of structures that their supports undergo different motions during an earthquake.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.436-441
• /
• 2008

One of important factors in designing array-type MEMS resonators is obtaining a desired frequency response function (FRF) within a specific range. In this paper Krylov subspace-based model order reduction using moment-matching with non-zero expansion points is represented to calculate the FRF of array-type resonators. By matching moments at a frequency around a specific range of the array-type resonators, required FRFs can be efficiently calculated with significantly reduced systems regardless of their operating frequencies. In addition, because of the characteristics of moment-matching method, a minimal order of reduced system with a specified accuracy can be determined through an error indicator using successive reduced models, which is very useful to automate the order reduction process and FRF calculation for structural optimization iterations.

• Journal of Broadcast Engineering
• /
• v.8 no.1
• /
• pp.3-10
• /
• 2003

This paper proposes a variable-Q digital graphic equalizer in which each equalizer filter has different Q-factor depending on the band as well as the gain. The proposed equalizer demonstrates the symmetric frequency response over the audible frequency range. While maintaining the similar level of hardware complexity, the proposed equalizer yields an actual response that is quite close to the desired one, as compared with the conventional equalizers. Also, we investigate how the performance is affected by the center frequencies of the filters.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.1
• /
• pp.77-82
• /
• 2010

An analytical method for robust design of the multi-loop proportional-integral (PI) controller is proposed for various types of multi-delay processes. On the basis of the direct synthesis and generalized IMC-PID approach, the analytical tuning rules of the multi-loop PI controller are firstly derived for achieving the desired closed-loop response, and the structured singular value synthesis is then utilized for the tradeoffs between the robust stability and performance by adjusting only one design parameter (i.e., the closed-loop time constant). To verify the superiority of the proposed method, the simulation studies have been conducted on a wide variety of multivariable processes. The multi-loop PI controller designed by the proposed method shows a fast, well-balanced and robust response with the minimum integral absolute error (IAE) in compared with other renowned methods.

• Steel and Composite Structures
• /
• v.17 no.6
• /
• pp.951-965
• /
• 2014

Point bending is commonly used for cambering and curving steel girders to large radii. In this system, a hydraulic ram or press is used to apply concentrated loads at selected points to obtain the required vertical (cambering) or horizontal (curving) curved profile from induced permanent deformations. This paper derives closed form solutions that relate loads to permanent deformations for horizontally curving wide flange steel beams based on their post-yield response. These solutions are presented in a parametric form to identify the relationship between key variables and their impact on the accuracy of the curving operation. It is shown that point bending could yield parabolic curved profiles that are within 1% of a desired circular curve if the span length to radius of curvature ratio (L / R) is less than 1.5 and the point loads are spaced at one third the beam length. Safe limits are then established on loads, strains and curvatures to avoid damaging the steel section. This leads to optimization of the point bending operation for inducing a circular profile in wide flange steel beams of any size.

• 제어로봇시스템학회:학술대회논문집
• /
• 1998.10a
• /
• pp.407-412
• /
• 1998

A design technique based on the root locus approach for the SISO (Single-Input Single-Output) systems using PID (Proportional-Integral-Derivative) ${\times}$ (n-1) stage PD as a controller for the n$\^$th/ order plant is presented. The controller is designed based on transient and steady state response specifications. This controller can be used instead of a conventional PID controller. The overall system is approximated as a stable and robust second order system. The desired performances are achieved by increase the gain of the controller. In addition, the controller gain can be adjusted to obtain faster response with a little overshoot. The simulation results show the merits of this approach.

• Structural Engineering and Mechanics
• /
• v.54 no.4
• /
• pp.623-648
• /
• 2015

A numerical approach is presented for the analysis of the forced vibration of a rigid surface foundation with arbitrary shape. In the analysis, the foundation is discretized into a number of sub squaree-lements. The dynamic response within each sub-element is described by the Green's function, which is obtained by the Fourier-Bessel transform and Precise Integration Method (PIM). Incorporating the displacement boundary condition and force equilibrium of the foundation, it obtains a system of linear algebraic equation in terms of the contact forces within each sub-element. Solving the equation leads to the desired dynamic impedance functions of the foundation. Numerical results are obtained for foundation not only with simple geometrical configurations, such as rectangular and circular foundation, but also the case of irregularly shaped foundation. Several comparisons between the proposed approach and other methods are made. Very good agreement is reached. Also, parametric studies are carried out on the dynamic response of foundation. Addressed in this study are the effects of Poisson's ratio, material damping and contact condition of soil-foundation interface. Several conclusions are drawn the significance of the factors.