• 한국농공학회지
• /
• 제30권3호
• /
• pp.69-81
• /
• 1988

The Repeated Load Triaxial and Oedometer Tests to the weathered granite & silty clay soil have been fulfilled to investigate their dynarnic characteristics. The results obtained are summarized as follows ; 1. In the relation between the repeated triaxial compression and the oedometer test, the recoverable strain of weathered granite soil showed a tendency to decrease by the increase of the repeated loads number(N), and that of silty clay showed approximately constant values while the total strain increased continuously. 2. The changes of plastic strain was dependent to the level of deviator stress which is the most important element in the calculation of soil deformation under repeated load condition. And there was a significance of 10% between the level of stress and plastic strain. 3. When the soil was aimost dried or saturated to 100%, the deformation by the repeated loads was small. However the deformation showed peak around the saturation of 50%. 4. When the deformation was predicted by the repeated triaxial load tests of a laboratory, it is desirable to introduce the threshold stress concept in the calculation of deformation of subgrade of the pavement. 5. The improved design equation (Eq. 16) introducing the modulus of conversion(Fo), which is based on the Boussineq' s theory, is considered to be rational in the design of flexible pavement. From the above results, the deformation to the repeated traffic loads could be predicted by the repeated triaxial tests on the pavement materials or undisturbed soil layers, therefore it is think that the durable and econornic pavement could be constructed by reflecting that to the design.

• 한국기계가공학회지
• /
• 제11권5호
• /
• pp.1-7
• /
• 2012

The transportation is almost dependent on a single fuel petroleum with transportation energy dilemma. Hybrid Electric Vehicle(HEV) technology holds more advantages on efficiency improvements for petroleum consumption at the transportation. And bearing is recognized as the important component of gearbox. Gearboxes for HEV transmission have been ensured the highest reliability over some years in withstanding high dynamic loads. At the same time, the demands of lightweight design and cost minimization are required by thought-out design, high-quality material, superior production quality and maintenance. In order to design a reliable and lightweight gearbox, it is necessary to analyze bearing rating life methods between standard and different bearing companies with calculation methods for modification factors. In this paper, the influence of life time of bearings will be pointed out. Bearing contact stress and load stress distribution of HEV gearbox are obtained and compared with Romaxdesigner and BearinX. And the unequal wear of the left bearing for the gearbox intermediate shaft is investigated between simulation and test.

• 한국기계가공학회지
• /
• 제11권4호
• /
• pp.25-30
• /
• 2012

The transportation is almost dependent on a single fuel petroleum with transportation energy dilemma. Hybrid Electric Vehicle(HEV) technology holds more advantages on efficiency improvements for petroleum consumption at the transportation. And bearing is recognized as the important component of gearbox. Gearboxes for HEV transmission have been ensured the highest reliability over some years in withstanding high dynamic loads. At the same time, the demands of lightweight design and cost minimization are required by thought-out design, high-quality material, superior production quality and maintenance. In order to design a reliable and lightweight gearbox, it is necessary to analyze bearing rating life methods between standard and different bearing companies with calculation methods for modification factors. In this paper, the influence of life time of bearings will be pointed out. Bearing contact stress and load stress distribution of HEV gearbox are obtained and compared with Romaxdesigner and BearinX. And the unequal wear of the left bearing for the gearbox intermediate shaft is investigated between simulation and test.

• Advances in materials Research
• /
• 제5권4호
• /
• pp.205-221
• /
• 2016

In this article, the buckling responses of functionally graded curved (spherical, cylindrical, hyperbolic and elliptical) shell panels under elevated temperature load are investigated numerically using finite element steps. The effective material properties of the functionally graded shell panel are evaluated using Voigt's micromechanical model through the power-law distribution with and without temperature dependent properties. The mathematical model is developed using the higher-order shear deformation theory in conjunction with Green-Lagrange type nonlinear strain to consider large geometrical distortion under thermal load. The efficacy of the proposed model has been checked and the effects of various geometrical and material parameters on the buckling load are analysed in details.

• Journal of Welding and Joining
• /
• 제17권2호
• /
• pp.29-35
• /
• 1999

This study was intended to use for the fatigue test in real structures and offer basic data for optimum welding structure design. To this purpose, we obserded the effect of the size and distance of plug welding hole on the static strength and fatigue life of welding structure under the shear/bending load for the improvement of fatigue life of plug welding joint between S/MBR and C/MBR in the lower structure of large bus. The result below is shown through this study. 1) Static and fatigue strength are strongly influenced by the direction of plug weld hole distributed. 2) Distances and diameters of the distributed holes are little dependent on the static strengths 3) In case of the directions of the distributed plug weld holes are vertical to the loading pin, fatigue life is dependent on distance of the distributed hole. 4) In case of the directions of the distributed plug weld holes are parallel to the loading pin, fatigue life is dependent on distance of the hole diameter.

• ETRI Journal
• /
• 제37권3호
• /
• pp.562-572
• /
• 2015

For a multiprocessor System-on-Chip (MPSoC) to achieve high performance via parallelism, we must consider how to partition a given application into different components and map the components onto multiple processors. In this paper, we propose a software pipeline-based partitioning method with cyclic dependent task management and communication optimization. During task partitioning, simultaneously considering computation load balance and communication optimization can cause interference, which leads to performance loss. To address this issue, we formulate their constraints and apply an integer linear programming approach to find an optimal partitioning result - one that requires a trade-off between these two factors. Experimental results on a reconfigurable MPSoC platform demonstrate the effectiveness of the proposed method, with 20% to 40% performance improvements compared to a traditional software pipeline-based partitioning method.

• 대한기계학회논문집B
• /
• 제38권4호
• /
• pp.289-309
• /
• 2014

풍력터빈 블레이드는 바람의 운동에너지를 기계적 에너지로 변환하는 장치로써 풍력발전시스템의 출력성능, 에너지변환효율, 하중 및 동적 안정성에 영향을 미칠 수 있기 때문에 주요부품으로 분류된다. 따라서 최적의 블레이드 설계결과를 얻기 위해서는 시스템 특성이 고려된 공력-구조 통합설계가 중요하다. 본 연구에서는 풍력터빈 시스템과의 상호작용이 고려된 블레이드 설계절차를 제안하였고, 2 MW 급 블레이드(KR40.1b)의 공력-구조 통합 설계결과를 제시하였다. 또한 전술한 바와 같이 로터 블레이드에 작용하는 극한하중 및 피로하중은 시스템 운전조건에 따라 가변적이므로 시스템통합하중해석을 위한 2 MW 풍력발전시스템 모델링을 수행하였으며, IEC 61400-1 및 (사)한국선급의 풍력발전기술기준에 따라 수행된 하중해석결과를 제시하였다.

• Journal of Mechanical Science and Technology
• /
• 제20권12호
• /
• pp.2061-2078
• /
• 2006

The main purpose of this paper is to establish the high temperature structural integrity evaluating procedures for the next generation reactors, which are to be operated at over 500$^{\circ}C$ and for 60 years. To do this, comparison studies of the high temperature structural design codes and assessment procedures such as the ASME-NH (USA), RCC-MR (France), DDS (Japan), and R5 (UK) are carried out in view of the accumulated inelastic strain and the creep-fatigue damage evaluations. Also the application procedures of the ASME-NH rules with the actual thermal and structural analysis results are described in detail. To overcome the complexity and the engineering costs arising from a real application of the ASME-NH rules by hand, all the procedures established in this study such as the time-dependent primary stress limits, total accumulated creep ratcheting strain limits, and the creep-fatigue damage limits are computerized and implemented into the SIE ASME-NH program. Using this program, the selected high temperature structures subjected to two cycle types are evaluated and the parametric studies for the effects of the time step size, primary load, number of cycles, normal temperature for the creep damage evaluations and the effects of the load history on the creep ratcheting strain calculations are investigated.

• 품질경영학회지
• /
• 제45권2호
• /
• pp.293-306
• /
• 2017

Purpose: In this study, an optimal design level of influencing factors on semiconductor polishing process was determined to minimize flexion of both sides on wafers. Methods: First, significant interactions are determined by the stepwise regression method. ANOVA analysis on SN ratio and mean of dependent variable are performed to draw mean adjustment factors. In addition, the optimal levels of mean adjustment factors are decided by comparing means of each level of mean adjustment factors. Results: As a result of ANOVA, a mean adjustment factor was determined as a width of formed flexion on the plate. The mean of the difference has the nearest to 0 in the case when the width of formed flexion has level 2 (4mm). Conclusion: Optimal design levels of semiconductor polishing process are determined as follows; (i) load applied to the wafer carrier has a level 1 (3psi), (ii) load applied to the wafer has a level 1(3psi), (iii) the amount of slurry supplied during polishing has a level 3 (300 co/min), (iv) the width of formed flexion on the plate has level 2 (4mm).

• Composites Research
• /
• 제33권5호
• /
• pp.288-295
• /
• 2020

섬유강화 복합재 적층판은 높은 비강성과 비강도를 가지고 있으며, 자동차 및 항공과 같은 무게에 민감한 산업에서 경량화에 유용할 것으로 기대되고 있다. 하지만 복합재 적층판의 설계는 적층 개수와 적층 순서를 모두 결정해야 하는 어려움으로 인해 설계자의 축적된 경험과 직관에 의존하는 경우가 많고, 이는 필요 이상으로 제품의 중량이 증가하는 과설계로 이어질 수 있다. 본 연구에서는 주어진 하중을 견디고 최소 무게를 갖는 복합재 적층판의 최적설계를 수행하였다. 나열법을 기반으로, 복합재 적층판의 설계 지침을 만족하는 모든 경우의 적층 조합을 고려하였다. 복합재 적층판을 여러 개의 패널로 나누고, 각 패널의 응력 분포와 인접한 패널 간 연결성을 고려하여 최적의 적층 수와 적층 순서를 결정하였다. 강도를 고려하기 위해 Tsai-Wu 파손 이론으로부터 파손 지수를 최적화하였고, 압축 하중에 대해서는 좌굴 해석을 수행하였다. 적층각은 일반적으로 사용하고 있는 0, ±45, 90°를 사용하였다.