• Wind and Structures
• /
• v.2 no.2
• /
• pp.119-125
• /
• 1999

The ZG Bridge(preliminary design), with unfavorable aerodynamic stability characteristics, is a truss-stiffened suspension bridge, its critical wind speed of flutter instability is much lower than that of code requirement, In the present paper, based on both aerostatic and aeroelastic section model wind tunnel test, not only effects of some aerodynamic means on aerodynamic stability of its main girder are investigated, but also such effective aerodynamic means of it as flap and plate-like center stabilizer are concluded.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.59 no.4
• /
• pp.109-117
• /
• 2017

Coastal reclamation has created large flat lands, part of which is an attractive site to construct greenhouse complexes for the horticulture industry. Wind environments over these coastal lands are entirely different from those of the inland area, and demand increased structural safety. The objective of this study is to evaluate the structural safety of two single-span greenhouses, peach type and even-span type, under the wind characteristics of coastal reclaimed lands. The wind pressure coefficients acting on the walls and roofs of two greenhouses were measured by wind tunnel experiments, and those acting on the roofs were approximately two times larger than those suggested by the existing design guidelines. Consequently, structural analysis conducted by SAP2000 showed that greenhouse structures designed by the existing guidelines might lead to structural failure under coastal wind conditions because their maximum allowable wind speeds were lower than the design wind speed. Especially, the peach type greenhouse constructed in a reclaimed land could be damaged by approximately 48 % of the design wind speed and needed improvement of structural designs. This study suggested increasing the spacing of rafters with thicker pipes for the peach type greenhouse to enhance economic feasibility of the building under strong wind conditions of reclaimed lands.

• Wind and Structures
• /
• v.15 no.1
• /
• pp.1-15
• /
• 2012

High-resolution wind data were acquired from a 100-m high offshore tower during the passage of Typhoon Hagupit in September, 2008. The meteorological tower was equipped with an ultrasonic anemometer and a number of cup anemometers at heights between 10 and 100 m. Wind characteristics of the strong typhoon, such as mean wind speed and wind direction, turbulence intensity, turbulence integral length scale, gust factor and power spectra of wind velocity, vertical profiles of mean wind speed were investigated in detail based on the wind data recorded during the strong typhoon. The measured results revealed that the wind characteristics in different stages during the typhoon varied remarkably. Through comparison with non-typhoon wind measurements, the phenomena of enhanced levels of turbulence intensity, gust factors, turbulence integral length scale and spectral magnitudes in typhoon boundary layer were observed. The monitored data and analysis results are expected to be useful for the wind-resistant design of offshore structures and buildings on seashores in typhoon-prone regions.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.10
• /
• pp.1455-1460
• /
• 2014

Wind turbine generators were designed on general regulations of wind condition. At real situations, it could be different from the design conditions. There are many control methods and definitions of transient region, because an efficient wind turbine generator control logic is the important matter in generator performance and annual energy production at real conditions. In this document, the power generation sensitivity for wind speed and turbulence intensities was defined to know the sensitive transient region. Wind conditions are applied for the ranges of 7~10m/s mean wind speed and 14~20% turbulence intensity. The sensibility of HR-D86 wind generator was increased in transient region(8~10m/s) on power curve diagram through a torque control to a pitch control. And then GH-bladed simulations was performed for performance analysis of the torque mode switching in transient region on 2MW direct drive wind generator(HR-D86) which is designed IEC class II for onshore. Through the sensitivity and performance analysis, the sensitivity for real wind condition could be the performance index for an wind generator. And the torque mode switching in transient region can increase the mean power generation on HR-D86 wind turbine generator.

• Structural Engineering and Mechanics
• /
• v.46 no.5
• /
• pp.735-753
• /
• 2013

The wind load is always the dominant load of cooling tower due to its large size, complex geometry and thin-wall structure. At present, when computing the wind-induced response of the large-scale cooling tower, the wind pressure distribution is obtained based on code regulations, wind tunnel test or computational fluid dynamic (CFD) analysis, and then is imposed on the tower structure. However, such method fails to consider the change of the wind load with the deformation of cooling tower, which may result in error of the wind load. In this paper, the analysis of the large cooling tower based on the iterative method for wind pressure is studied, in which the advantages of CFD and finite element method (FEM) are combined in order to improve the accuracy. The comparative study of the results obtained from the code regulations and iterative method is conducted. The results show that with the increase of the mean wind speed, the difference between the methods becomes bigger. On the other hand, based on the design of experiment (DOE), an approximate model is built for the optimal design of the large-scale cooling tower by a two-level optimization strategy, which makes use of code-based design method and the proposed iterative method. The results of the numerical example demonstrate the feasibility and efficiency of the proposed method.

• Journal of the Korean Solar Energy Society
• /
• v.30 no.6
• /
• pp.59-65
• /
• 2010

Analysis on turbulence intensity profile depending on wind speed is an important process to set up design condition of wind turbine in terms of fatigue load. This paper tests goodness of fit of turbulence intensity empirical equations suggested by the IEC 61400 Standards with Jejudo Gimnyeong met-tower measurement, which is erected at a seashore. Therefore sea breeze and land breeze coexist. Sea breeze case showed apparent increasing trend of turbulence intensity in a high wind speed regime due to increase of sea surface roughness. However, neither inland wind turbine standard IEC 61400-1 nor offshore wind turbine standard IEC 61400-3 fit such a trend adequately. On the other hand, the modified empirical equation of turbulence intensity of IEC 61400-3 derived from Germany FINO1 application study by considering turbulence intensity behavior in a high wind speed regime showed good agreement with the measurement. Therefore, we can reconfirm and conclude that IEC 61400-3 Ed.1 legislated in 2009 needs to be modified.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.17 no.1
• /
• pp.23-32
• /
• 2021

Conventional wind power generators have limited installation sites due to low efficiency due to reverse resistance or high cut-in speed. To compensate for these problems, this study proposed another new type of tilting wind turbine. The key to this method is the structural design of a cylindrical cam with a guide groove that allows the blade to tilt. As the blade rotates by the cam, it tilts according to the angle. In the section that generates torque by receiving drag, the blade is made perpendicular to the wind. And it is a structure that creates a parallel state with the wind in the section where reverse resistance occurs. We prepared six types of cams considering the length of the section subject to drag, reverse resistance, tilting section. The performance was analyzed as the maximum value of the output, torque coefficient, and efficiency coefficient, which is indicated by setting different wind speed and low TSR.

• International Journal of Advanced Culture Technology
• /
• v.10 no.4
• /
• pp.518-528
• /
• 2022

Virtual Reality (VR) has been widely used in various applications to generate realistic virtual environments. A sense of immersion can be increased by providing additional stimuli such as tactile sensation to VR contents. However, it is still challenging to provide a realistic feel for the wind blowing over the whole body by smoothly controlling the airflow. To address this issue, we employ a household electric fan as a wind generating device to provide users with wind experience in VR environments. The wind generating device targets the whole body to mimic the wind we feel outside in our daily life. To do so, we present a low-cost method to smoothly control household fan speed using an Arduino microcontroller. Here, we use the Sinusoidal Pulse Width Modulation (SPWM) technique to generate the sinusoidal voltage required to drive the fan motor. Our experimental results show how Variable Voltage Variable Frequency (VVVF) is implemented at a low cost using our method for household fan speed control. The results can be applied to various VR applications to enhance the sense of immersion by providing users with realistic wind.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.3
• /
• pp.262-268
• /
• 2014

This research introduces the structural design and the validation results of the flexible high speed coupling for 2MW class wind turbine which transmit and cut off torque between gear box and generator. The high speed coupling requires electrical insulation to prevent electrical surface damages on gear box. Therefore glass fiber reinforced plastics is applied to absorb the vibration and deformation of power train and to transmit required torque. Finite element analysis was performed to optimize the thickness and accumulation number of glass fiber reinforced plastics. Torque limiter which cut off the abnormal torque is designed in frictional disc type. The design of the coupling was validated with the performance test of prototype.

• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.603-605
• /
• 1999

In this paper, the aspects on modeling and control of an existing wind turbine are discussed. When designing control for variable-speed wind turbine, one deals with highly resonant, nonlinear dynamic systems subject to random excitation, i.e. wind turbulence. This requires good knowledge of the dynamics to be controlled. This paper describes an mathematical modeling of wind turbines with emphasis on control design for an existing wind turbine.