• Fire Science and Engineering
• /
• v.26 no.3
• /
• pp.106-111
• /
• 2012

In this study, EIFS (Exterior insulation finish system) of exterior cladding was applied Cone calorimeter test to confirm the effect of flame retardant. As a results, the initial ignition points in accordance with the coated form and concentration of the flame retardant was delayed. But flame resistant treatment of EIFS cladding to control the fire will not affect confirmed that. In addition, EIFS that uses high-density and low-density due to difference in the density of the impact of the fire was no difference. The exterior of the ignition experiment occurred before and after 40 seconds, heat release rate to 100 seconds appears to occur about 90 % compared with the other exterior wall materials, the initial fire spread very fast was confirmed. EIFS cladding in order to prevent the spread of fire in the application of EIFS legally use is limited by the use of the building. And flame spread can be prevented, such as a vertical outer wall compartment measures are urgently needed.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.6
• /
• pp.196-205
• /
• 2017

In precast deck system, structural performance and serviceability are mostly determined by the connection methods between the precast decks. This study proposes precast deck system with asymmetric ribbed connection details using High Strength Fiber Reinforced Concrete(HSFRC) with filler. To verify the proposed method, the flexural performance experiment was carried out with variation of joint cross section type and splice rebar details. From the test results, regardless of joint details, spliced tensile rebars of specimens were deformed to yielding strain level. Also, all types of specimens resulted in sufficient flexural performance. These test results show that the minimum lap splice length specified in current Korea Highway Bridge Design Code is conservative for precast deck joint using HSFRC. Therefore, splice details can be simplified and joint width can be reduced by using HSFRC with filler between the precast decks, and the proposed precast deck systems can be applied to the connection part of precast decks effectively.

• Journal of Distribution Science
• /
• v.13 no.12
• /
• pp.73-84
• /
• 2015

Purpose - Various social issues have arisen since the beginning of the 21st century therefore, enterprises that disregarded social issues have become unsustainable, and social enterprises have appeared to address these issues. A social enterprise is a social mission-focused organization that uses a market-based strategy and has a vulnerable business structure. To be self-sustainable, a social enterprise should make consumers aware of the value that it provides and secure its profitability through consumer consumption. From this perspective, this study investigates the relationship between perceived value (utilitarian and hedonic) and loyalty, and examines how memory and attitudes play mediating roles between perceived value and loyalty. For these purposes, the author developed a structural model consisting of several variables. In this model, perceived value, which was utilitarian and hedonic, was proposed to affect the memory and attitudes toward social enterprise products, thus increasing loyalty. Therefore, memory and attitudes were proposed as core mediating variables between perceived value and loyalty. Research design, data, and methodology - To analyze the proposed model, data were collected from 582 respondents and analyzed using SPSS 21.0 and AMOS 21.0. To test unidimensionality and the nomological validity of the measures of each construct, we employed a scale refinement procedure. The results of the reliability test with Cronbach's α and confirmatory factor analysis warranted the unidimensionality of the measures for each construct. In addition, the nomological validity of the measures was warranted from the results of the correlation analysis. The result of the overall model analysis demonstrated a good fit (χ²=529.881, df=144, χ²/df=3.680, p-value=0.000, GFI=0.905, NFI=0.948, CFI=0.961, RMR=0.036, RMSEA=0.068). Results - The findings are summarized as follows. First, the hedonic and utilitarian value of social enterprise products had positive effects on memory and attitudes. Second, the hedonic value of social enterprise products more strongly affects memory and attitudes than utilitarian value. Third, memory and attitudes had positive effects on loyalty. Lastly, memory had a stronger effect on loyalty than attitudes. Conclusions - The purchase rate of social enterprises' products increases only if the products are included in the "information search" and "alternative evaluation" processes in consumers' purchase decision-making processes. Therefore, a social enterprise must actively promote the fact that it pursues a social value, and shares both the hedonic and utilitarian values of its products. Accordingly, because hedonic value has a more significant impact on a company and attitudes, a social enterprise should develop hedonic values for product consumption, thereby leading consumers who care about value consumption to purchase its products. Moreover, a social enterprise must maintain good memories and attitudes for consumers because memory does not change over time, although attitude does. The limitations of this study and suggestions for future research are as follows. This study viewed "consumer loyalty" as the success factor of social enterprises, thereby considers an "increase in sales" as the success factor. Therefore, in future studies, diverse factors, including social contribution and word-of-mouth intention, should be regarded. In addition, future studies need to thoroughly review and make assurances about the relationship between memory and attitude.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.1
• /
• pp.79-85
• /
• 2016

Recently, visible light communication(VLC) is being actively researched as green wireless communication services are drawing attention. Currently, VLC mostly uses LED for transmission and PD(Photo Diode) for receiving. However, this kind of system has limited applications. Therefore, we design and propose in this paper, a LED-to-LED two way VLC system that doesn't use PD(Photo Diode). This system has the following features and contributions. First, this system uses just LED at both transmitter and receiver with analog switch, Second, this system support both one-way communication and two way communication together. One way communication can support multi-hop communication. The performance evaluation of the proposed system is conducted at a place with standard light. We test the success or failure of one way communication by changing distance and baud rate while test the success and failure of two way communication by changing distance. We expect that the proposed LED-to-LED system in this paper can be applied for various application fields.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.109-112
• /
• 2008

In this study, Assessment of bond property of HSC with the rate of Blust-furnace(0, 12, and 25 percent by weight cement) and Evaluation of the relationship of the compressive strength coefficient (${\beta}$) between compressive strength with 40${\sim}$120MPa were performed. Design and Test of Bond specimens were carried out based on the ASTM C-234. Test results are follows, most specimens showed that the splitting failure in all specimens, except for B-40 series which showed that the pull-out failure. For the B-40 Series, the relation of compressive strength versus bond stress has well converged that of the proposed equation with the variation(${\beta}$=2/3) in UCB/E.E.R.C-83. The crack strength of concrete in splitting was proportioned to the compressive strength of concrete, and was the highest on the contents of blast furnace slag to 12 percent by weight of cement in each series, except for B-60 series. In the relation of admixture replacement rate versus maximum bond stress, The maximum bond stress was the highest in 12 percent by weight of cement according to less than 40MPa, and was the highest in 25 percent by weight of cement according to 80MPa.

• Journal of the Korea Institute of Building Construction
• /
• v.20 no.1
• /
• pp.43-51
• /
• 2020

The main purpose of protective facility for small military unit is to provide the protection of not all the weapons system but the near-miss bullet in Korean army. In particular about the small caliber bullets, especially KM80 in Korea, there were many studies that both of the experiential and structural design methods dose not reflect enough the military threat. For that reason, a new equation to calculate effective anti-piercing depths for RC slabs against small caliber bullets is proposed in earlier research with actual shooting test. But, the test only considers the strength of concrete without the thickness of concrete, types of aggregate, the angle of yaw of bullet, high-strength concrete, etc. Therefore, this study evaluated the ballistic resistance performance by thickness and proportion of magnetic aggregate of concrete. As a result, we identified two major statistical estimations that the error of piercing depth by the angle of yaw of bullet could be cancelled by barrage and the thickness and proportion of magnetic aggregate of concrete dose not effect on the protection ability of concrete structure.

• 전자공학회논문지 IE
• /
• v.47 no.1
• /
• pp.22-33
• /
• 2010

The main purpose of this study was to develope a reflective journal and examine its effects on student's academic achievement and self-regulated learning strategies. For this study, 'a structured reflective journal' was designed through the steps of systems approach with the purpose of enhancing student's academic achievement and self-regulated learning strategies, especially meta-cognition and critical thinking. The reflective journal used in this study contained the constructive elements of (1) self-evaluation with 5 likert scale, (2) learning essay, (3) dialogue with peers, and (4) dialogue with professor. A total of 94 freshmen enrolled in one of two sections of the engineering courses(theory-based class and experiment and practice-based class) participated in the study for 8 weeks. A pre-test-post-test design was used to examine the effects of the application of reflective journal on student's achievement and self-regulated learning strategies. For the result, analysis of covariance was conducted to determine whether there were any academic achievement differences and self-regulated learning strategy differences. The results suggested that students were taking advantages of the reflective journal, and there were statistically significant differences in academic achievement in the experiment and practice-based class and self-regulated learning strategies in both classes.

• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.1
• /
• pp.41-47
• /
• 2010

Purpose: The purpose of this study was to compare the functional abilities of the low bulb obturators with those of high bulb obturators in terms of patients' evaluation. Material and methods: This study included 11 maxillectomy patients who underwent postoperative prosthodontic rehabilitations. Two obturators of the same design except for different bulb heights, were fabricated for each of the maxillectomy patient. After two months of alternate use, the functions of the obturators were measured by investigating the patients' subjective evaluations in terms of convenience, speech, nasality, leakage, and mastication and identifying their preferred prostheses. Wilcoxon signed rank test was used as a statistical method (P < .05). Results: There were no significant differences in patient evaluations of low and high bulb obturators (P >.05). And patients' preferences varied. Conclusion: In extreme situation such as in mouth opening limitation, the use of low bulb obturators can be recommended and result in comparable speech function to that of obturators with high lateral walls.

• Elastomers and Composites
• /
• v.42 no.1
• /
• pp.20-31
• /
• 2007

Material characteristics and lifetime evaluation are very important in design procedure to assure the safety and reliability of the rubber components. In this paper, the NBR compound was prepared by sulfur-cure system, and was used in predicting the lifetime of rubber gasket made by the compound. The accelerated material aging was investigated at different temperatures at 120, 140 and $160^{\circ}C$ and aging time from 3 hours to 600 hours at 5, 6, 7 vol %. of $H_2SO_4$ concentrations The rubber strips were placed in acid solution using pyrex g1ass tube. Both ends of pyrex g1ass tube were sealed to avoid evaporation of solution during heating at given time. The material test and accelerated acid-heat aging test were carried out to predict the useful life of NBR rubber gasket for a fuel cell stack. In order to investigate the effects of acid-heat aging on the properties of the NBR, tensile strength, elongation at break, hardness and crosslink-density were measured. The tensile strength decreases as the $H_2SO_4$ concentrations and temperature increase. Results were evaluated using Arrhenius equation.

• Journal of Pharmaceutical Investigation
• /
• v.38 no.2
• /
• pp.135-142
• /
• 2008

The present study describes the evaluation of the bioequivalence of two atorvastatin tablets, Lipitor $Tablet^{(R)}$ (Pfizer, reference drug) and Atorva $Tablet^{(R)}$ (Yuhan, test drug), according to the guidelines of Korea Food and Drug Administration (KFDA). Forty-nine healthy male Korean volunteers received each medicine at the atorvastatin dose of 40 mg in a $2{\times}2$ crossover study with a two weeks washout interval. After drug administration, serial blood samples were collected at a specific time interval from 0-48 hours. The plasma atorvastatin concentrations were monitored by an high performance liquid chromatography -tandem mass spectrometer (LC-MS/MS) employing electrospray ionization technique and operating in multiple reaction monitoring (MRM) and positive ion mode. The total chromatographic run time was 4.5 min and calibration curves were linear over the concentration range of 0.1-100 ng/mL for atorvastatin. The method was validated for selectivity, sensitivity, linearity, accuracy and precision. $AUC_t$ (the area under the plasma concentration-time curve from time zero to 48hr) was calculated by the linear log trapezoidal rule method. $C_{max}$ (maximum plasma drug concentration) and $T_{max}$ (time to reach $C_{max}$) were complied trom the plasma concentration-time data. Analysis of variance was carried out using logarithmically transformed $AUC_t$ and $C_{max}$. No significant sequence effect was found for all of the bioavailability parameters indicating that the crossover design was properly performed. The 90% confidence intervals of the $AUC_t$ ratio and the $C_{max}$ ratio for Atorva $Tablet^{(R)}$ / Lipitor $Tablet^{(R)}$ were ${\log}\;0.9413{\sim}{\log}\;1.0179$ and ${\log}\;0.831{\sim}{\log}\;1.0569$, respectively. These values were within the acceptable bioequivalence intervals of ${\log}\;0.8{\sim}{\log}\;1.25$. Based on these statistical considerations, it was concluded that the test drug, Atorva $Tablet^{(R)}$ was bioequivalent to the reference drug, Lipitor $Tablet^{(R)}$.