• 설비공학논문집
• /
• 제13권5호
• /
• pp.356-367
• /
• 2001

A numerical analysis on branch type sparger in drain tank for depressurization is performed to investigate the flow characteristics due to the change of design factor. As the result of this study, sparger\\`s flow resistance coefficient(K) is 3.53 at the present design condition when engineering margin for surface roughness is considered as 20%, and flow ratio into branch pipe ($Q_s/Q_i$) is 0.41. The correlation for calculating flow resistance coefficients as design factor is presented. Flow resistance coefficient is increased as section area ratio of branch pipe for main pipe and outlet nozzle diameter of main pipe decreasing, but the effects of branch angle and inlet flow rate of main pipe are small. As the change rate of ($Q_s/Q_i$)becomes larger, the change rate of flow resistance coefficient increases. The rate of pressure loss has the largest change as section area ratio changing. The condition of maximum flow resistance in sparger is when the outlet nozzle diameter ratio of main pipe ($D_e/D_i$) is 0.167, the section area ratio ($A_s/A_i$) is 0.1 and the branch angle ($\alpha$) is 55^{\circ}$.

• Nuclear Engineering and Technology
• /
• 제56권7호
• /
• pp.2458-2473
• /
• 2024

The turbulent flow in reactor pressure vessel (RPV) of pressurized water reactor (PWR) is important for the flow rate distribution at core inlet. Thus, it is vital to study the turbulent flow phenomena in RPV. However, the complicated fluid channel consisted of inner structures of RPV will block or refract the laser sheet of particle image velocimetry (PIV). In this work, the matched index of refraction (MIR) of sodium iodide (NaI) solution and acrylic was applied to support optical path for flow field measurements by PIV in the 1/10th scaled-down RPV model. The experimental results show detailed velocity field at different locations inside the scaled-down RPV model. Some interesting phenomena are obtained, including the non-negligible counterflow at the corner of nozzle edge, the high downward flowing stream in downcomer, large vortices above vortex suppression plate in lower plenum. And the intensity of counterflow and the strength of vortices increase as inlet flow rate increasing. Finally, the case of asymmetry flow was also studied. The turbulent flow has different pattern compared with the case of symmetrical inlet flow rate, which may affect the uniformity of flow distribution at the core inlet.

• KIEAE Journal
• /
• 제11권1호
• /
• pp.29-38
• /
• 2011

This study suggested practical application of climate design on apartment complex with the focus on the use of Cold Air Flow and green building design method. The domestic research on the wind path analysis has been associated since the early 21th century in urban planning and site planning, this initiative study aimed to mitigate the urban heat island effect and to promote the sustainable urban development. It is, however, mostly focused on the flow analysis and heat flow in the urban context, due to the poor application of the wind path analysis in actual planning and design. Special attention is paid to the possibilities of identifying and developing the application methods in relation to Cold Air Flow and building design. This study examined these relations and suggested some trenchant approach to a more comprehensive and efficient use of the wind flow analysis in climate design.

• 한국정보처리학회논문지
• /
• 제6권10호
• /
• pp.2752-2763
• /
• 1999

On account of the text based mail system has it's limit to support multimedia applications, GUI based mail system platform was developed to control document flow and automatize information process. The existing mail systems's to transmit data must need additional functions to automate document flow control. The platform of document flow control is deeply related to EDMAS(Electronic document Management System), workflow, Electronic Banking, DMS(Document Management System) automation, so it needs an ability to control proper data and document correctly. To resolve this problems, we are need of browser and engine to design work flow and to control documents flow. In this paper, we develope a mail browser to design document flow by follow user's requirements. This system can generate executive script code for document flow, and we add the function of workflow and process management to automatize the document flow in this system, and then we implement this Data flow engine.

• 한국자동차공학회논문집
• /
• 제11권4호
• /
• pp.1-6
• /
• 2003

Steady flow bench test is a practical, powerful and widely used in most engine manufacturers to give a design concept of a new engine. In order to use steady data as a performance index, it is necessary to build some database, which can correlate the port characteristics with engine data. However, it is very difficult to investigate all port shapes with experimental tools. The steady flow scheme is relatively simple and its results are bulk ones such as flow rate and momentum of flow. Therefore a CFD code can be easily applied to the port evaluation. In this study, the steady flow test was simulated through three-dimensional analysis on intake port design for comparing with experimental data and confirming the feasibility of applying analytic method . for this purpose, the effect of valve curvature on flow rate was estimated by a CFD code. Numerical results were compared with those of real steady flow tests. As a result, the results of 3-D analysis were almost consistent with experimental data.

• 한국수자원학회논문집
• /
• 제41권12호
• /
• pp.1173-1185
• /
• 2008

노면배수시설의 설계방법을 임계지속시간의 고려 여부와 등류 및 부등류의 해석 방법에 따라 4가지로 구분하고, 각 방법에 따른 설계결과를 비교·검토하였다. 임계지속시간을 고려하지 않는 방법에서 설계강우는 10분 지속시간의 강우강도로 정하나, 임계지속시간을 고려할 경우 설계강우는 강우의 지속시간과 유출의 도달시간이 유사해지는 경우를 시산적으로 찾아 결정한다. 4가지 설계방법으로 수립된 설계모형을 다양한 수로의 종단경사 및 길어깨 횡단경사를 가지는 노면배수시설에 적용하고, 그 설계결과를 비교 검토하였다. 10분 지속시간의 강우강도를 이용하는 경우, 부등류 해석을 기반으로 설계한 유출구 간격은 종단경사와 길어깨 횡단경사가 작은 경우에만 등류 해석보다 크게 산정되었다. 반면 도달시간을 산정하여 임계지속시간을 결정하는 경우에는 본 연구에서 고려된 모든 조건에서 부등류 해석을 기반으로 설계한 유출구 간격이 등류 해석보다 크게 산정되었다. 그러나 도달시간을 산정하여 임계지속시간을 결정하고 부등류 해석을 기반으로 설계한 유출구 간격은 10분 지속시간의 강우강도를 적용하고 등류 해석을 기반으로 설계한 값보다 항상 작은 것으로 조사되었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 춘계학술대회논문집; 경주코오롱호텔; 22-23 May 1997
• /
• pp.615-620
• /
• 1997

The flow rate and the noise level of 18 cross flow fans were measured to analyze the effect of design variables on these and to finally find the optimal design value. These data were analyzed by the Taguchi method and the neural network. The optimal values obtained by the neural network showed good agreements with that by the Taguchi method. The effects of eight design variables on the fan performance and the noise were evaluated and discussed.

• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2007년도 정기총회 및 학술발표대회
• /
• pp.632-635
• /
• 2007

Detention pond has an important role in peak flow reduction to mitigate flood damage. Design of detention pond is accomplished through the preliminary stage, planning stage, and design stage in general. New development projects produce increased peak flow and flow amounts. In this case it is necessary to design the detention pond easily and simply. The simple procedure of detention pond design is proposed in this study. The relevant variables are peak flow ratio ($\alpha$) for the before and after development, and storage ratio which is ratio of storage volume to flow amounts. Simplified method for the detention pond design with runoff reduction is easily used for practical purposes.

• 한국자동차공학회논문집
• /
• 제6권5호
• /
• pp.28-36
• /
• 1998

In order to establish the hydraulic design process of the torque converter, pump, turbine and stator were designed by reverse design method including one dimensional analysis, angular momentum distribution and forced vortex design. And the significance of evaluation of the circulation flow rate in torus of the torque converter was verified by numerical calculation if the combined blade rows of pump and turbine. It was confirmed that the computational method using interrow mixing model by Park and Cho was reliable to predict the flow-field and performance of the torque converter.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1997년도 추계 학술대회논문집
• /
• pp.38-42
• /
• 1997

A multiblock grid generation has been applied to a Navier-Stokes design procedure of a axial-flow compressors. A multiblock structure simplifies the creation of structured H-grids about complex turbomachinery geometries and facilitate the creation of a grid in the tip flow region. The numerical algorithm adopts the combination of the algebraic and elliptic method to create the internal grids efficiently and quickly. The input module is made of the results of the preliminary design, i.e., flow-path, aerodynamic conditions along the spanwise direction, and the blade profile data. The final grids generated from each module of the system are used as the preprocessor for the performance prediction of the sectional blade, the blade-stacking process and the three-dimensional flow simulation inside the blade passage. Application to the blade design of the LP compressor was demonstrated to be very reliable and practical in support of design activities. This customized system are coupled strongly with the design procedure of the turbomachinery cascades using the Navier-Stokes technique.