• Journal of the Korean Ceramic Society
• /
• v.46 no.5
• /
• pp.441-446
• /
• 2009

Dense crack-free yttria film with 10 $\mu m$ thickness was prepared on aluminum by aerosol deposition. X-ray diffraction pattern on the film showed that it contained the same crystalline phase as the raw powder. Transmission electron microscopy revealed a nanostructured yttria film with grains smaller than 100 nm. Tensile adhesion strength between the film and aluminum substrate was 57.8 $\pm$ 6.3MPa. According to the etching test with $CF_4-O_2$ plasma, the etching rate of the yttria film was 1/100 that of quartz, 1/10 that of sintered alumina and comparable to that of sintered yttria.

• Journal of the Korean Ceramic Society
• /
• v.50 no.6
• /
• pp.533-538
• /
• 2013

Silicon carbide (SiC) materials are typical ceramic materials with a wide range of uses due to their high hardness and strength and oxidation resistance. In particular, due to the corrosion resistance of the material against acids and bases including the chemical resistance against ionic gases such as plasma, the application of SiC has been expanded to extreme environments. In the SiC deposition process, where chemical vapor deposition (CVD) technology is used, the reactions between the raw gases containing Si and C sources occur from gas phase to solid phases; thus, the merit of the CVD technology is that it can provide high purity SiC in relatively low temperatures in comparison with other fabrication methods. However, the product yield rarely reaches 50% due to the difficulty in performing uniform and dense deposition. In this study, using a computational fluid dynamics (CFD) simulation, the gas velocity inside the reactor and the concentration change in the gas phase during the SiC CVD manufacturing process are calculated with respect to the gas velocity and rotational speed of the stage where the deposition articles are located.

• Corrosion Science and Technology
• /
• v.6 no.1
• /
• pp.18-23
• /
• 2007

DLC coatings have been deposited onto substrate of STS 316L and Ti alloy using r.f. PACVD (plasma-assisted chemical vapor deposition) with a mixture of $C_{6}H_{6}$ and $SiH_{4}$ as the process gases. Corrosion performance of DLC coatings was investigated by electrochemical techniques (potentiodynamic polarization test and electrochemical impedance spectroscopy) and surface analysis (scanning electron microscopy). The electrolyte used in this test was a 0.89% NaCl solution of pH 7.4 at temperature $37^{\circ}C$. The porosity and protective efficiency of DLC coatings were obtained using potentiodynamic polarization test. Moreover, the delamination area and volume fraction of water uptake of DLC coatings as a function of immersion time were calculated using electrochemical impedance spectroscopy. This study provides the reliable and quantitative data for assessment of the effect of substrate on corrosion performance of Si-DLC coatings. The results showed that Si-DLC coating on Ti alloy could improve corrosion resistance more than that on STS 316L in the simulated body fluid environment. This could be attributed to the formation of a dense and low-porosity coating, which impedes the penetration of water and ions.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.5
• /
• pp.418-422
• /
• 1998

The Co-Cr films are one of the most suitable candidates for perpendicular magnetic recording media. The facing targets sputtering(FTS) system has a advantage of preparing films over a wide range of working gas pressure on plasma-free substrate. In this study, we investigated the possibility of employing FTS system for depositing Co-Cr films. The Co-Cr thin films were deposited with various sputter gas pressure($P_Ar$, 0.1~10mTorr) by using FTS apparatus at temperature of $40^{\circ}C and 220^{\circ}C$, respectively. Crystallographic and magnetic characteristics were evaluated by x-ray diffractometry (XRD) and vibrating sample magnetometer(VSM), respectively. Under argon gas pressure at 0.1mTorr, films with morphologically dense microstructure, good c-axis orientation and higher coercivity were obtained. It has been confirmed that the FTS system is very useful for preparing Co-Cr thin film recording media.

• Journal of the Korean Society of Tobacco Science
• /
• v.17 no.1
• /
• pp.33-40
• /
• 1995

Structures of the adventitious root meristem induced from callus culture of tobaco (Nicotiana tabacum cv. NC 82) leaves were investigated by light and transmission electron microscopy. Structural differences between in vitro root and callus cells were also examined by the microscopy. The submicroscopic features of the in vitro root cells were as follows. Intercellular spaces were not developed and nuclei with two nucleoli were observed occasionally. Plasmodesmate were found in groups or sing1y on transverse and longitudinal walls. Amyloplast solely filled with starch grains, with one to five electron - dense bands, was surrounded by single membrane. in the callus cells, vacuolization of central part in the cytoplasm having mitochondria with swollen cristae and starch grains like those of in vitro root cells was a distinct feature. Vesicles which were found between cell wall and plasma membrane may be arisen by a process of protoplasmic invagination. By comparing of ultrastructures between the cells of callus and in vitro roots we found that the distinct differences lied on thickened cell walls and hypertrophed vacuoles in the former, and less thickened cell walls and several small vacuoles in the later.

• Journal of the Korean institute of surface engineering
• /
• v.52 no.4
• /
• pp.211-226
• /
• 2019

Optical thin films were deposited by using a reactive pulsed DC magnetron sputtering method with a high density plasma(HDP). In this study, the effect of sputtering process conditions on the microstructure and optical properties of $SiO_2$, $TiO_2$, $Nb_2O_5$ thin films was clarified. These thin films had flat and dense microstructure, stable stoichiometric composition at the optimal conditions of low working pressure, high pulsed DC power and RF power(HDP). Also, the refractive index of the $SiO_2$ thin films was almost constant, but the refractive indices of $TiO_2$ and $Nb_2O_5$ thin films were changed depending on the microstructure of these films. Antireflection films of $Air/SiO_2/Nb_2O_5/SiO_2/Nb_2O_5/SiO_2/Nb_2O_5/Glass$ structure designed by Macleod program were manufactured by our developed sputtering system. Transmittance and reflectance of the manufactured multilayer films showed outstanding value with the level of 95% and 0.3%, respectively, and also had excellent durability.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.4
• /
• pp.176-181
• /
• 2003

Rapid densification of a SiC powder with additive 0.5 wt% $B_4$C was conducted by spark plasma sintering (SPS). The unique features of the process are the possibilities of using very fast heating rate and short holding time to obtain fully dense materials. The heating rate and applied pressure were kept to be $100^{\circ}C$/min and 40 MPa, while sintering temperature and soaking time varied to 1800, 1850, 1900 and $1950^{\circ}C$ and 10, 20 and 30 min, respectively. All of the SPS-sintered specimens at $1950^{\circ}C$ reached near-theoretical density. The XRD found that 3C-to-6H transformation at $1850^{\circ}C$. The microstructures of the rapidly densified SiC ceramics consisted of duplex microstructure with ultrafine equiaxed grains under 2 $\mu\textrm{m}$ and elongated grains of 0.5∼2 $\mu\textrm{m}$ wide, length 3∼10 $\mu\textrm{m}$. The biaxial strength increased with the increase of sintering time. Strength of 392.7 MPa was obtained with the fully densified specimen sintered at $1950^{\circ}C$ for 30 min, in agreement with the general tendency that strength increases with decreases pore. On the other hand, the fracture toughness shows the value of 2.17∼2.34 MPa$.$$m^{1/2}$ which might be due to the transgranular fracture mode.

• Journal of Veterinary Clinics
• /
• v.40 no.2
• /
• pp.93-103
• /
• 2023

The tendon is a dense connective tissue that connects muscle to bone and plays an essential role in joint motion. The injured tendon heals slowly owing to its low cellularity and vascularity. This study aimed to evaluate and compare the effects of regenerative injection therapy (RIT), 20 % dextrose prolotherapy (DP), and platelet-rich plasma (PRP) injections that can promote tendon healing. Twenty-one New Zealand white rabbits were divided into the control, DP, and PRP treatment groups. The superficial digital flexor tendon (SDFT) of the right hindlimb of each rabbit was used. A round defect of 2 mm was induced. Approximately 0.2 mL of 20% dextrose and autologous PRP were injected into the proximal and distal ends of the SDFT mass. Radiographic and ultrasonographic examination and cross-sectional area (CSA) calculations were performed pre-operatively and at 2, 4, and 8 weeks. The SDFT of both limbs was transected for biomechanical and histomorphometric evaluations. The SDFT of the left limb was transected for intact control. Semi-quantitative analysis was performed to evaluate the histomorphometric properties. Additional analysis was performed using H&E, Masson's trichrome, and immunohistochemical staining. The biomechanical evaluation showed that the treatment groups had higher tensile strength compared to the defect control group, while the PRP group had higher tensile strength than the DP group. On histological examination, the treatment groups appeared to be relatively closer to the remodeling phase of the healing process than the defect control group; the characteristics of the PRP group were closer to the remodeling phase than those of the DP group. The ultrasonographic examination showed different tendencies. Increased values in the CSA were observed during the early period in the treatment groups. This study suggests that PRP and DP can promote the healing of tendon injury, and these effects were superior with PRP than that with DP.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.27 no.4
• /
• pp.315-323
• /
• 2005

For reconstruction of the bony defect, distraction osteogenesis has many advantages in comparison with bone graft. However, it needs long consolidation period for sufficient bone maturity. This study is performed to evaluate the effect of PRP injection into the distracted mandible on bone formation in rabbits. Twelve house rabbits, weighing 2 kg, were used. All animals underwent bilateral mandibular osteotomy under general anesthesia. A internal distractor divice was positioned along a plane perpendicular to the line of osteotomy. After 5 days of latency period, distraction osteogenesis was started at a rate of 1 mm/day for 9 days which was distracted 9 mm totally. After completion of distraction, 0.5 ml of PRP which collected in rabbit blood was injected into the distracted mandible on experimental group, whereas no injection was done in control group. Macroscopical, radiographical, and histological, and histomorphometric examinations were performed 2, 4 and 8 weeks after distraction. All animals showed distracted mandible and severe anterior cross-bite. In radiographical findings 2 weeks after distraction, more radiopacity in the distracted gap was found in experimental group than that of control group. At 4 weeks after distraction, distracted bone was similar to normal bone in experimental group. In histological findings, 1) At 2 weeks after distraction, number of osteoblasts and angiogenesis in the distracted gap was found in experimental group than that of control group. 2) At 4 weeks after distraction, more active and distinct bone in the distracted gap was found in experimental group than that of control groups. 3) At 8 weeks after distraction, more dense and matured lamellated bone in the distracted gap was found in experimental group than that of control group. In histomorphometrical findings 8 weeks after distraction, more bone formation was observed in experimental group than control group (p<0.01). These results indicate that administration of PRP into the distracted mandible can promote bone formation.

• Asian-Australasian Journal of Animal Sciences
• /
• v.17 no.8
• /
• pp.1139-1144
• /
• 2004

In Exp. 1, a total of 36 pigs (6.55$\pm$0.10 kg average initial body weight and 21 d average age) were used in a 14 d growth study to determine the effects of replacing spray-dried plasma protein (SDPP) with spray-dried egg protein containing specific egg yolk antibody (SDEP) on growth performance and nutrient digestibility in weaned pigs. The pigs were blocked by weight and assigned to treatments based on sex. There were three pigs per pen and four pens per treatment. Dietary treatments were 0, 3, or 6% SDEP and contained 6, 3, or 0% SDPP, respectively. Through the entire experimental period, average daily gain (ADG), average daily feed intake (ADFI), and gain/feed tended to decrease as the concentration of SDEP increased in the diets. However, there were no significant differences among the treatments (p>0.05). As the addition of SDEP in the diets increased, apparent digestibilities of dry matter (DM) and nitrogen (N) were decreased without significant (p>0.05). For Exp. 2, 36 pigs (2.63$\pm$0.04 kg average initial body weight and 10 d average age) were used in a 14 d growth study to determine the effects of antibiotic replacement with SDEP on growth performance and nutrient digestibility in early-weaned pigs. The pigs were blocked by weight and assigned to treatments based on sex. There were three pigs per pen and four pens per treatment. Dietary treatments included 1) ANTIBIOTIC (corn-dried whey-soybean meal based diet+0.08% antibiotics, 4 mg of tiamuline hydrogen fumarate; 10 mg of sulfadimidine per kg of complete diet), 2) SDEP0.1 (corndried whey-SBM based diet+0.1% SDEP), and 3) SDEP0.2 (corn-dried whey-SBM based diet+0.2% SDEP). ADG and gain/feed of pigs fed the SDEP0.2 diet were higher than for pigs fed the ANTIBIOTIC diet without significant (p>0.05). Pigs fed the diet with SDEP0.2 tended to have increased apparent digestibilities of DM and N compared to pigs fed the ANTIBIOTIC diet without significant (p>0.05). In conclusion, the dietary SDEP seemed to be partial replacing the SDPP portion of high nutrient dense diet for weaned pigs. Also, dietary SDEP seemed to be approximately 0.2% or more when the pigs fed the antibiotic-free diet for early-weaned pigs.