• 조명전기설비학회논문지
• /
• 제19권1호
• /
• pp.169-174
• /
• 2005

지금까지의 고조파 필터는 중성선 리액터와 지그재그결선의 영상 고조파 전류를 제거하였으나, 부하율에 따라 고조파 저감율이 변하여 경부하에서는 고조파 저감율이 낮아지는 특성이 있고, 중성선 리액터 과열로 중성선 단선 위험의 문제가 발생하였다. 본 Zig-Zag 결선 및 Open Delta 방식을 이용한 새로운 고조파 저감장치(HANOS)는 Zig-Zag 결선의 Core Block내에 추가로 Open Delta 방식을 결선하여 중성선에 연결함으로써 중성선에 흐르는 영상 고조파 전류가 과열 없이 안전하게 제거되는 것을 시험 분석한 결과로 증명하였다.

• Kyungpook Mathematical Journal
• /
• 제59권3호
• /
• pp.537-562
• /
• 2019

The aim of the present paper is to study the ${\delta}$-Lorentzian trans-Sasakian manifold endowed with semi-symmetric metric connections admitting ${\eta}$-Ricci Solitons and Ricci Solitons. We find expressions for the curvature tensor, the Ricci curvature tensor and the scalar curvature tensor of ${\delta}$-Lorentzian trans-Sasakian manifolds with a semisymmetric-metric connection. Also, we discuses some results on quasi-projectively flat and ${\phi}$-projectively flat manifolds endowed with a semi-symmetric-metric connection. It is shown that the manifold satisfying ${\bar{R}}.{\bar{S}}=0$, ${\bar{P}}.{\bar{S}}=0$ is an ${\eta}$-Einstein manifold. Moreover, we obtain the conditions for the ${\delta}$-Lorentzian trans-Sasakian manifolds with a semisymmetric-metric connection to be conformally flat and ${\xi}$-conformally flat.

• 전기학회논문지
• /
• 제64권11호
• /
• pp.1543-1550
• /
• 2015

Ferroresonance is a non-linear vibrational phenomenon that is generated by the electrical interaction of the inductance component with the capacitor component of a certain capacitance as the device of the inductance component such as a transformer is saturated due to the degradation, the waveform distortion of current and voltage, and the oscillation of overcurrent and overvoltage in a system. Recently, ferroresonance was generated from the waveform distortion of current and voltage, or the overvoltage or undervoltage phenomenon caused by the nature of an electrical power system and design technology of the transformer in the three phase transformer system. Hence, in general, ferroresonance analyzed by converting to the LC equivalent circuit. However, in general, the aforementioned analytical method only applies to the resonance phenomenon that is generated by the interaction of the capacitance of bussbar and grounding, and switching as the capacitor component with PT and the transformer as the inductance component in a system. Subsequently, the condition where ferroresonance was generated since overvoltage was supplied as line voltage to the phase voltage and thus the iron core is saturated due to the interconnection between grounded and ungrounded systems could not be analyzed when single phase PT was connected in a ${\Delta}$/Y connection system. In this study, voltage swell in the configuration of grounded circuit of a step-up transformer with the ${\Delta}-{\Delta}$ connection linked to PT for control power and the ferroresonance generated by overvoltage when the line voltage of the ${\Delta}-{\Delta}$ connection was connected to the phase voltage of the grounded Y-Y connection were analyzed using PSCAD / EMTDC through the failure case of the transformer caused by ferroresonance in the system with the ${\Delta}-{\Delta}$/Y-Y connection, and subsequently, the preventive measure of ferroresonance was proposed.

• 대한기계학회논문집A
• /
• 제21권12호
• /
• pp.1992-2007
• /
• 1997

A new algorithm for planning a collision-free path is developed based on linear prametric curve. In this paper robot is assumed to a point, and two linear parametric curve is used to construct a path connecting start and goal point, in which single intermediate connection point between start and goal point is considered. The intermediate connection point is set in polar coordinate(${\theta}{\delta}$) , and the interference between path and obstacle is mapped into CPS(connection point space), which is defined a CWS GM(circular work space geometry mapping). GM of all obstacles in workspace creates overlapping images of obstacle in CPS(Connection Point Space). The GM for all obstacles produces overlapping images of obstacle in CPS. The empty area of CPS that is not occupied by obstacle images represents collision-free paths in Euclidian Space. A GM based on connection point in elliptic coordinate(${\theta}{\delta}$) is also developed in that the total length of path is depend only on the variable .delta.. Hence in EWS GM(elliptic work space geometry mapping), increasing .delta. and finding the value of .delta. for collision-free path, the shortest path can be searched without carring out whole GM. The GM of obstacles expersses all possible collision-free path as empty spaces in CPS. If there is no empty space available in CPS, it indicates that path planning is not possible with given number of connection points, i.e. path planning is failed, and it is necessary to increase the number of connection point. A general case collision-free path planning is possible by appling GM to configuration space obstacles. Simulation of GM of obstacles in Euclidian space is carried out to measure performance of algorithm and the resulting obstacle images are reported.

• Journal of Magnetics
• /
• 제20권2호
• /
• pp.166-175
• /
• 2015

In this study, we describe the design method of a Brush-less DC (BLDC) motor with delta winding connection. After designing delta winding connection model with the $60^{\circ}$ flat-top region of the Back Electro-Motive Force (BEMF), an ideal current source analysis and a voltage source analysis, with a 6-step control, were conducted primarily employing Finite Element Method. In addition, as a current controller, we considered the Current Regulator with PI controller using Simulink for the comparison of torque characteristics. When the input current is controlled, the switching regions and reference signals are determined by means of the phase BEMF zero-crossing point. In reality, the input current variation depends on the inductance as well as input voltage, and it causes a torque ripple after all. Therefore, each control method considered in this research showed different torque ripple results. Based on the comparison, the causes of the torque ripple have been verified in detail.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권3호
• /
• pp.243-247
• /
• 2005

The Different-volume- V-connection transformer is known as an electric power source that can supply 3-phase electric power and single-phase electric power at the same time. Usually, we use two single-phase transformers that have different volumes. In this paper, we propose the use of a 3-phase 5-leg transformer with the different-volume- V-connection. And, we examine the magnetic properties of the 5-leg core model with the different-volume- V-connection. The magnetic properties of cores with the different-volume- V-connection are compared with those with the delta-connection. In order to express the magnetic anisotropy of the core materials and to calculate the iron loss directly, the two-dimensional vector magnetic property is considered with the E&SS modeling in the simulation.

• 한국강구조학회 논문집
• /
• 제17권4호통권77호
• /
• pp.469-479
• /
• 2005

강구조 비가새 골조의 접합부로서 반강접합부를 적용하게 되면 접합부의 비선형적인 모멘트-회전각 관계는 강구조 비가새 골조의 거동($P-\Delta$ 효과) 및 안정성에 영향을 미치게 된다. 따라서 본 연구에서는 이러한 접합부 비선형 거동이 골조의 거동 및 안정성에 미치는 영향을 2차 비탄성 해석을 통하여 고찰하고, 안정성에 영향을 미치는 주요 인자 및 그 경향들을 분석하였다. 연구 결과 접합부의 비선형 거동은 골조의 안정성에 직접적인 영향을 미치는 것으로 나타났으며 주요 영향인자는 접합부의 회전강성, 반강접합부의 적용 위치 등으로 나타났다.

• Journal of Mechanical Science and Technology
• /
• 제18권1호
• /
• pp.92-105
• /
• 2004

A new algorithm for planning a collision-free path based on algebraic curve is developed and the concept of collision-free Path Space (PS) is introduced. This paper presents a Geometry Mapping (GM) based on two straight curves in which the intermediate connection point is organized in elliptic locus ($\delta$, $\theta$). The GM produces two-dimensional PS that is used to create the shortest collision-free path. The elliptic locus of intermediate connection point has a special property in that the total distance between the focus points through a point on ellipse is the same regardless of the location of the intermediate connection point on the ellipse. Since the radial distance, a, represents the total length of the path, the collision-free path can be found as the GM proceeds from $\delta$=0 (the direct path) to $\delta$=$\delta$$\_$max/(the longest path) resulting in the minimum time search. The GM of elliptic workspace (EWS) requires calculation of interference in circumferential direction only. The procedure for GM includes categorization of obstacles to .educe necessary calculation. A GM based on rectangular workspace (RWS) using Cartesian coordinate is also considered to show yet another possible GM. The transformations of PS among Circular Workspace Geometry Mapping (CWS GM) , Elliptic Workspace Geometry Mapping (EWS GM) , and Rectangular Workspace Geometry Mapping (RWS GM), are also considered. The simulations for the EWS GM on various computer systems are carried out to measure performance of algorithm and the results are presented.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.1128-1131
• /
• 1996

The collision-free path planning presented here uses linear parametric curve with one intermediate connection point between start and target points. The algorithm, in which connection point is organized in elliptic chord.(.theta., .delta.), maps objects in Euclidean Space into images in CPS through intersection check between path and obstacles a process defined as GM. Elliptic locus has special property that the total distance between focus points through a point on ellipse is the same regardless of .theta.. Hence by locating the start and target points to focus points of ellipse, and organizing connection point in elliptic coordinate, the .delta.-axis of CPS represents length of path. The GM of EWS requires calculation of interference in circumferential direction only. The procedures for GM is developed which include categorization of obstacles to reduce calculation amount. Simulations of GM of EWS, on a PC with Pentium/90MHz, is carried out to measure performance of algorithm and the results are reported on a table. The simulations are done for number of cases with different number of obstacles and location of start/target points.

• 한국지반환경공학회 논문집
• /
• 제8권1호
• /
• pp.49-55
• /
• 2007

폐타이어의 트레드를 지반보강재로서 활용하기 위해서는 타이어 외면 및 내면과 흙간의 내부마찰각 그리고 폐타이어 연결부의 강도특성을 알아야 한다. 본 연구에서는 폐타이어 트레드와 모래 및 풍화토간의 접촉면마찰각을 알기 위해 흙의 다짐정도를 달리하여 대형직접전단시험을 수행하였다. 직접전단시험 결과 모래-타이어 외면간의 마찰각비(${\delta}/{\phi}$)는 1.06배 이상, 모래-트레드 내면간의 ${\delta}/{\phi}$는 0.93배 이상, 풍화토의 마찰각비(${\delta}/{\phi}$)는 트레드 외면과 내면에 대하여 각각 0.98, 0.92로 나타났다. 또한 UTM을 이용하여 폐타이어 연결부의 재료에 따른 인장강도시험을 수행하였다. 시험 결과 고장력 볼트를 사용한 인장시험에서 볼트의 개수 및 와셔의 크기가 증가할수록 연결부에서의 인장강도는 증가하였으며 폴리프로필렌 로프 연결의 경우가 볼트연결의 경우보다 작은 강도를 나타내었다.