• 소성∙가공
• /
• 제19권7호
• /
• pp.416-422
• /
• 2010

The $\{10\bar{1}2\}$ twinning characteristics, such as active twin variants, volume fraction of twins with strain, twin morphology, twin texture and angle relationship between twins, were dependent on the activation mode (i.e., tension parallel to the caxis or compression perpendicular to the c-axis). The selection criterion of active twin variants was governed by the Schmid law. This activation of selected twin variants depending on the activation mode consequently caused a totally different plastic deformation behavior in two activation modes. The differences in the deformation characteristics, such as flow stress and work hardening rate, between both activation modes were explained in relation with activation stresses for slips and twinning, relative activities of twinning and slips during plastic deformation, grain refining effect by twin boundaries (Hall-Petch effect), and twinning-induced change in activities of slips.

• 소성∙가공
• /
• 제16권6호
• /
• pp.467-472
• /
• 2007

In this study, the effects of initial texture on the twinning formation of AZ31 Mg rolled sheet was investigated. Uniaxial compression tests were carried out on samples cut along the normal direction(ND) and roiling direction(RD), respectively, of rolled AZ31 Mg alloy sheet at various temperatures (RT, 200, 250, 300, 350, $400^{\circ}C$) with the fixed strain rate($10^{-2}/s$). The results showed that deformation twining occurred actively only in the RD specimens, which promoted homogeneous deformation as compared to the ND specimens. The effect of temperature on the formation of deformation twins was also investigated, and the slip/twin transition temperature was found to be approximately $250^{\circ}C$.

• 대한금속재료학회지
• /
• 제48권4호
• /
• pp.305-314
• /
• 2010

The development of textures and microstructures during plastic deformation in a hot-extruded AZ 31 Mg alloy was investigated using a compression test with such parameters as deformation temperature, strain rate. It was observed from true stress-strain curves that twinning involves changes of the flow stresses. In the early stages of deformation at temperatures lower than $200^{\circ}C$, the occurrence of twins resulted in a decrease of the work-hardening rate, which increased drastically at a true strain of -0.05. The evolution of the deformation textures were assessed with the aid of EBSD analyses in terms of the competition between twinning and slip activity.

• 열처리공학회지
• /
• 제15권1호
• /
• pp.9-15
• /
• 2002

Deformation behavior of nickel-rich Ti-51.5at.%Ni single crystals was investigated over a wide range of temperatures(77 to 440K) and strain levels(up to 9%) in compression. These alloys combined superior strength with wide range of pseudoelasticity temperature interval(~200K). The slip deformation in [001] orientation did not occur due to the prevailing slip system, and consequently, exhibited pseudoelastic deformation at temperatures ranging from 77 to 283K and 273 to 440K for the solutionized and over-aged cases, respectively. The critical transformation stress levels were in the range of 800 to 1800MPa for the solutionized case, and 200 to 1000MPa for the over-aged case depending on the temperature and specimen orientation. These stress levels are considerably higher compared to these class of alloys having lower Ni contents. The maximum transformation strains, measured from incremental straining experiments in compression, were lower compared to the phenomenological theory with Type II twinning. A compound twinning model depending on the successive austenite(B2) to intermediate phase(R) to martensite(B19') transformation predicts lower transformation strains compared to the Type II twinning case.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.1057-1060
• /
• 2001

By comparison of the experimental results in two systems of ZnO varistors, its appear that Sb$_2$O$_3$is the indispensable element for twinning in ZnO varistors, and the Zn$_{7}$Sb$_2$O$_{12}$ spinel acts as the nucleus to form twins. A1$_2$O$_3$is not the origin of twinning in ZnO varistor, but it was found that A1$_2$O$_3$could strengthen the twinning and form a deformation twinning by ZnA$_{12}$O$_4$-dragging and pinning effect. The inhibition ratios of grain growth and nonuniformity of two systems ZnO varistors increase with the increase of A1$_2$O$_3$content. The twins affect the inhibition of grain growth, the mechanism could be explained follow as : twins increase the mobility viscosity of ZnO grain and grain boundary, and drag ZnO grain and liquid grain boundary during the sintering, then the grain growth is inhibited, and the microstructure becomes more uniform.orm.m.

• Nuclear Engineering and Technology
• /
• 제38권7호
• /
• pp.619-638
• /
• 2006

Low temperature irradiation can significantly harden metallic materials and often lead to strain localization and ductility loss in deformation. This paper provides a review on the radiation effects on the deformation of metallic materials, focusing on microscopic and macroscopic strain localization phenomena. The types of microscopic strain localization often observed in irradiated materials are dislocation channeling and deformation twinning, in which dislocation glides are evenly distributed and well confined in the narrow bands, usually a fraction of a micron wide. Dislocation channeling is a common strain localization mechanism observed virtually in all irradiated metallic materials with ductility, while deformation twinning is an alternative localization mechanism occurring only in low stacking fault energy(SFE) materials. In some high stacking fault energy materials where cross slip is easy, curved and widening channels can be formed depending on dose and stress state. Irradiation also prompts macroscopic strain localization (or plastic instability). It is shown that the plastic instability stress and true fracture stress are nearly independent of irradiation dose if there is no radiation-induced phase change or embrittlement. A newly proposed plastic Instability criterion is that the metals after irradiation show necking at yield when the yield stress exceeds the dose-independent plastic instability stress. There is no evident relationship between the microscopic and macroscopic strain localizations; which is explained by the long-range back-stress hardening. It is proposed that the microscopic strain localization is a generalized phenomenon occurring at high stress.

• Applied Microscopy
• /
• 제45권2호
• /
• pp.37-43
• /
• 2015

In present work, work-hardening behavior of TiCu-based bulk metallic glass composite with B2 particles has been studied by systemic structural and mechanical investigations. After yield, pronounced work-hardening of the alloy was clearly exhibited, which was mainly related to the martensitic transformation as well as the deformation twinning in B2 particles during deformation. At the early plastic deformation stage (work-hardening stage), the stress-induced martensitic transformation from B2 phase to B19' phase and deformation-induced twinning of B19' phase was preferentially occurred in the around interface areas between B2 phase and amorphous matrix by stress concentration. The higher hardness value was observed in vicinity of interface within the B2 particles which are probably connected with martensitic transformation and deformation twinning. This reveals that the work-hardening phenomenon of this bulk metallic glass composite is a result of the hardening of B2 particles embedded in amorphous matrix.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.114-117
• /
• 2007

In the present study, the effects of initial texture on the twinning formation of AZ31 Mg rolled sheet was investigated. Uniaxial compression tests were performed on samples cut along the normal direction and rolling direction of rolled AZ31 Mg alloy sheet at various temperatures (RT, 200, 250, 300, 350, $400^{\circ}C$) with the 0.01/s strain rate. Pole figure of rolling planes showed that basal planes of most gain were located parallel to the rolling direction. After compression test, microstructures and stress-strain curves results indicated that active deformation twining occurred only at the specimen cut along the rolling direction. The slip-twin transition with the increase of temperature was also investigated.

• 소성∙가공
• /
• 제27권5호
• /
• pp.301-313
• /
• 2018

In this paper, tensile test was performed on pure titanium sheet (CP Ti sheet) with HCP structure in each direction to evaluate mechanical and surface properties and analyze microstructural changes during plastic deformation. We also evaluated forming limits of Ti direction in dome-type punch stretching test using a non-contact three-dimensional optical measurement system. As a result, it was revealed the pure titanium sheet has strong anisotropic property in yield stress, stress-strain curve and anisotropy coefficient according to direction. It was revealed that twinning occurred when the pure titanium sheet was plastic deformed, and tendency depends differently on direction and deformation mode. Moreover, this seems to affect the physical properties and deformation of the material. In addition, it was revealed the pure titanium sheet had different surface roughness changes in 0 degree direction and 90 degree direction due to large difference of anisotropy, and this affects the forming limit. It was revealed the forming limit of each direction obtained through the punch stretching test gave higher value in 90 degree direction compared with forming limit in 0 degree direction.

• The Korean Journal of Ceramics
• /
• 제4권3호
• /
• pp.207-212
• /
• 1998

By comparison of the experimental results in two systems of ZnO varistors, it's appear that Sb2O3 is the indispensable element for twining in ZnO varistors and the Zn7Sb2O12 spinel acts as the nucleus to form twins. Al2O3 is not the origin of twining in ZnO varistor, but it was found that Al2O3 could strengthen the twining and form a deformation twining by ZnAl2O4 dragging and pinning effect. The inhibition ratios of grain and nonuniformity of two systems ZnO varistors increase with the increase of Al2O3 content. The twins affect the inhibition of grain growth, the mechanism could be explained follow as: twins increase the mobility viscosity of ZrO grain and grain boundary, and drag ZrO grain and liquid grain boundary during the sintering, then the grain growth is inhibited and the microstructure becomes more uniform.