• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.215-216
• /
• 2006

To lower the cost of MIM products, the gate and runner materials and green parts with defects are usually recycled. It is necessary to understand what causes the recycled products to deteriorate. The results show that the viscosity of the 1R (recycled once) feedstock was slightly lower than that of the fresh material. However, as the number of recyclings increased, the viscosity increased, while the density decreased, and more defects were noticed duri ng solvent debinding. These deteriorations were mainly caused by the increase of the melting point of the backbone binder and the oxidation of the filler or paraffin wax.

• 한국표면공학회지
• /
• 제49권2호
• /
• pp.172-177
• /
• 2016

In this paper, various electrochemical experiments were conducted in seawater solution to evaluate corrosion damage behavior of arc thermal sprayed Inconel 625 coating on SS400 steel in marine environment. As a result, corrosion damages of thermal sprayed Inconel 625 coating preferentially occurred at the defect area, and they were observed as a form of pitting corrosion in the galvanostatic experiments. In Tafel analysis, corrosion current density of Inconel 625 coating was relatively high due to influence of interconnected pores and Cr oxides in the thermal spray coating layer. On the other hand, the result of the potential measurement, thermal sprayed Inconel 625 coating should need the post-treatment which can compensate the defects like pores and cracks because Inconel 625 coating presented a higher potential of about 290 mV than that of the SS400 steel.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권5호
• /
• pp.633-639
• /
• 1995

Dropouts in magnetic media are a primary quality deficiency which is detrimental to magnetic signal quality and thus the major impediment to error-free recording, especially in high density digital recorders. The specific form of defects and causes found to be responsible for signal dropouts occurring in magnetic tape were studied. Dropout occurred when the RF signal falls to low level due to the various types of surface defects. However, the fall in the level of the RF signal in gravure roll coated tapes was most often caused by foreign particles adhering to the magnetic tape. It was also shown from the present study that scattered particles trapped under the tape surface or put on the top can lift it as it crosses the head, creating a spherical tent shaped defect and causing a temporary signal drop. Dropout producing substances were identified through optical and microchemical analyses. The results were correlated with measured electrical signal losses combined with analytical microscopy to clarify source identification of defects.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.389-392
• /
• 2004

As the integrated circuit device shrinks to the smaller dimension, the chemical mechanical polishing (CMP) process was required for the global planarization of inter-metal dielectric(IMD) layer with free-defect. The effect of alternative commerical slurries pads, and post-CMP cleaning alternatives are discuess, with removal rate, scratch dentisty, surface roughness, dishing, erosion and particulate density used as performance metrics. we investigated the performance of $SnO_2$-CMP process using commonly used silica slurry, ceria slurry, tungsten slurry. This study shows removal rate and non-uniformity of $SnO_2$ thin film used to gas sensor by using Ceria, Silica, W-Slurry after CMP process. This study also shows the relation between particle size and CMP with particle size analysis of used slurry.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.184-187
• /
• 2003

As the integrated circuit device shrinks to the smaller dimension, the chemical mechanical polishing (CMP) process was required for the global planarization of inter-metal dielectric(IMD) lyaer with free-defect. The effect of alternative commerical slurries pads, and post-CMP cleaning alternatives are discuess, with removal rate, scratch dentisty, surface roughness, dishing, erosion and particulate density used as performance metrics. we investigated the performance of $SnO_2-CMP$ process using commonly used silica slurry, ceria slurry, tungsten slurry. This study shows removal rate and nonuniformity of $SnO_2$ thin film used to gas sensor by using Ceria, Silica, W-Slurry after CMP process. This study also shows the relation between partical size and CMP with partical size analysis or used slurry.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 학술대회 및 기술세미나 논문집 디스플레이 광소자
• /
• pp.85-88
• /
• 2006

The transport properties of amorphous selenium typical of the material used in direct conversion x-ray imaging devices are reported. The effects of As addition on the carrier mobility and recombination lifetime in amorphous selenium (a-Se) films have been studied using the moving photocarrier grating (MPG) technique. We have found an increase in hole drift mobility and recombination lifetime, especially when 0.3% As is added into a-Se film, whereas electron mobility decreases with As addition due to the defect density. The transport properties for As doped a-Se films obtained by using MPG technique have been compared with the drift mobilities of holes and electrons obtained by time of flight (TOF) measurement.

• Journal of Chest Surgery
• /
• 제3권2호
• /
• pp.143-148
• /
• 1970

Bleomycin is known as a antibiotic agent for malignant tumors especially sguamous cell carcinoma. We have treated 2 cases of malignant tumors, each one esophageal and lung carcinoma with bleomycin, 630 mg and 510 mg respectively. In case of esophageal carcinoma. the subjective symptoms such as dysphagea and swallowing disturbance are temporally relieved, but the irregular filling defect is not significantly changed in esophagogram. In case of lung carcinoma, the atelectasis of right upper lobe on chest X-ray was slightly regressed in its size without effective improvement of subjective symptoms. However, following additional radioactive $^60{Co}$ irradiation therapy (5200r), marked regression of tumor density and aeration of right upper lobe was observed. But 2 weeks later of ceasatioil of irradiatio:J, atelectasis of right upper lobe was again developed. Fever, anorexia, headache and eruption were developed during the treatmeat with bleomycin in both cases but the sign or symptoms of hone marrow depression, renal or liver damage were not noted.

• 한국표면공학회지
• /
• 제47권6호
• /
• pp.275-281
• /
• 2014

An ultrasound-assisted Sn-Ag-Pd activation method for electroless copper plating was presented in this study. With this activation process, it was shown that the fine catalyst particles were homogeneously distributed with high density on the entire specimen. In addition, it was observed that incubation period occurred during the electroless plating step was decreased owing to the absorption of Ag which holds high catalytic activity. Resulting from the refinement and high densification of catalyst, the defect-free gap-fill was achieved within the 20x nm trench.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집 특별세미나,특별/일반세션
• /
• pp.527-532
• /
• 2009

Recently, Interior Permanent Magnet Machine(IPM) is widely used for traction motor in the high speed train. Due to the high efficiency and high power density of the IPM, it has lots of heat sources such as iron loss and copper loss. These heat sources can cause the demagnetization of permanent magnet, losses in output power and even irreversible defect of the IPM. To prevent the power loss caused by heat sources, the accurate thermal analysis has to be carried out. For the thermal analysis of the IPM, the thermal network is designed for this traction motor. The thermal analysis has executed at rated speed operation. The result of thermal network analysis can be used for the IPM design process.

• Nuclear Engineering and Technology
• /
• 제51권2호
• /
• pp.479-489
• /
• 2019

Low-cycle fatigue (LCF) tests were performed for Alloy 690 and 316 SS in a simulated pressurized water reactor (PWR) environment. Alloy 690 showed about twice longer LCF life than 316 SS at the test condition of 0.4% amplitude at strain rate of 0.004%/s. Observation of the oxide layers formed on the fatigue crack surface showed that Cr and Ni rich oxide was formed for Alloy 690, while Fe and Cr rich oxide for 316 SS as an inner layer. Electrochemical analysis revealed that the oxide layers formed on the LCF crack surface of Alloy 690 had higher impedance and less defect density than those of 316 SS, which resulted in longer LCF life of Alloy 690 than 316 SS in a simulated PWR environment.