• Polymer(Korea)
• /
• v.27 no.3
• /
• pp.210-216
• /
• 2003

4-Vinyl-1-cyclohexene diepoxide (VCE)/diglycidyl ether of bisphenol-A (DGEBA) epoxy blends with benzylquinoxalinium hexafluoroanti-monate were cured using an electron-beam technique. The effect of DGEBA content to VCE on cure behavior, thermal stabilities, and mechanical properties was investigated. The composition of VCE/DGEBA blend system vaned within 100:0, 80:20, 60:40, 40:60, 20:80, and 0:100 wt%. The cure behavior and thermal stability of the cured specimens was monited by near-infrared spectroscopy and thermogravimetric analysis, respectively. Also, the critical stress intensity factor ($_{4}$) test of the cured specimens was performed to study the mechanical interfacial properties. As a result, the decreases of short side-chain structure and chain scission were observed in NIR measurements as the DGEBA content increases, resulting in varying the hydroxyl and carbonyl groups. And, the initial decomposition temperature (IDT), temperature of maximum weight loss (T$\_$max/), and decomposition activation energy (E$\_$d/) as thermal stability factors were increased with increasing the DGEBA content. These results could be explained by mean of decreasing viscosity, stable aromatic ring structure, and grafted interpenetrating polymer network with increasing of DGEBA content. Also, the maximum $_{4}$ value showed at mixing ratio of 40:60 wt% in this blend system. in this blend system.

• Journal of the Mineralogical Society of Korea
• /
• v.15 no.4
• /
• pp.243-257
• /
• 2002

Ca-type and Na-type bentonites show the great difference of some physicochemical properties. Na exchanged bentonite is mainly used for the foundry and construction materials in domestic utilization. This study tries to identify in detail the differences of some physicochemical properties and thermal properties between Ca-type and Na-type bentonites. Also the adsorption behavior and interlayer expansion for the HDTMA (Hexadecyltrimethylammonium) exchanged and CP (Cetylprydinium) exchanged Ca-type and Na-type bentonites were compared. Na-type bentonite shows the strong alkaline property, high viscosity and swelling compared to Ca-type bentonite. However, two types are very similar for the cation exchange capacity and MB (Methylene Blue) adsorption. The decomposition of adsorbed and interlayer water of Na-type bentonite is caused in the lower temperature than Ca-type bentonite. And Ca-type bentonite shows the decomposition of structural water in the lower temperature than Na-type bentonite. The interlayer expansion of montmorillonite resulted to the intercalation of HDTMA and CP into bentonite is so strongly caused from 12～15 $\AA$ to $40\AA$ (basal spacing). HDTMA-bentonite is almost expanded to $37～38\AA$ when 200% CEC equivalent amount of HDTMA is added, and CP-bentonite is fullly expanded to 40 $\AA$ in the 140% CEC equivalent amount of CP It means that CP causes the stronger interlayer expansion of montmorillonite and easier adsorption than HDTMA. Adsorption behaviors of CP into bentonite is so stable and continuously sorbed in the proportion to the treatment of amount until 200% of the CEC equivalents. CP-bentonite shows the same adsorption behavior regardless of Ca-type or Na-type montmorillonite.

• KSBB Journal
• /
• v.24 no.3
• /
• pp.267-272
• /
• 2009

During a dilute acid hydrolysis, degradation products are formed or liberated by pre-treatment of lignocelluloses depend on both the biomass and the pretreatment conditions such as temperature, time, pressure, pH, redox conditions, and addition of catalysts. In lignocellulosic biomass, sugars can be degraded to furfural which is formed from pentoses and 5-hydroxymethulfurfural (HMF) from hexoses. 5-HMF can be further degraded, forming levulinic acid and formic acid. Acetate is liberated from hemicellulose during hydrolysis. Some decomposed compounds hinder the subsequent bioconversion of the solubilized sugars into desired products, reducing conversion yields and rates during fermentation. In the present work, samples of rapeseed strawwere hydrolyzed to study the optimal pretreatment condition by assessing yields of sugars and decomposed products obtained under different reaction conditions ($H_2SO_4$ 0.5-1.25% (w/w), reaction time 0-20 min and temperature range 150-220 C). A careful analytical investigation of acid hydrolyzate of rapeseed straw has not yet been undertaken, and a well-closed mass balance for the hydrolyzate in general is necessary to verify the productivity and economic predictions for this process.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.4
• /
• pp.976-980
• /
• 2010

A series of arylacetylene resins with siloxane units were synthesized by the condensation reactions of m-diethynylbenzene magnesium reagents with various $\alpha,\omega$-bis(chloro)dimethylsiloxanes. These resins are liquids and are miscible with common organic solvents at room temperature. The structures of the resins were characterized by FT-IR, $^1H$ NMR, $^{13}C$ NMR, $^{29}Si$ NMR, and gel permeation chromatography (GPC). The thermal behaviors of the resins were examined with differential scanning calorimetry (DSC). These resins have good processability. They can be thermally cross-linked through the ethynyl groups to produce cured resins. The thermal and thermooxidative stabilities of the cured resins were studied by thermogravimetric analysis (TGA). The cured resins possess high thermal and thermooxidative stability. Their decomposition occurs at above $500^{\circ}C$ in both $N_2$ and air. With increasing the length of siloxane units in the resins, the thermal stability of the cured resins decreases in $N_2$. When the cured resins were sintered above $1450^{\circ}C$ under argon, hard and glassy SiOC ceramics were obtained. These SiOC ceramics have the decomposition temperatures at 5% weight loss above $800^{\circ}C$ in air.

• Resources Recycling
• /
• v.25 no.5
• /
• pp.36-43
• /
• 2016

The leaching behaviors of copper from chalcopyrite were investigated by sulfuric acid. The leaching of copper was examined according to concentration of sulfuric acid, leaching temperature and addition of hydrogen peroxide and ethylene glycol. The concentrations sulfuric acid and hydrogen peroxide in the leaching solution were increased, the leaching efficiencies of Cu were increased. At $30 -60^{\circ}C$, the leaching efficiency of Cu was increased but it was decreased at $70 - 80^{\circ}C$. The results were due to the increasing of hydrogen peroxide decomposition in the solution above $70^{\circ}C$. In the case of ethylene glycol added at $80^{\circ}C$, the decomposition of hydrogen peroxide was decreased and the leaching efficiency was increased. As a result of SEM analysis of leaching residue after leaching, the residue was found to porous form in the case of the ethylene glycol added and then the leaching efficiency of Cu was increased by the increase of surface area under $60^{\circ}C$ with ethylene glycol.

• Korean Chemical Engineering Research
• /
• v.43 no.5
• /
• pp.632-636
• /
• 2005

In this work, the effect of chemical treatments on surface properties of SiC was investigated in thermal and mechanical interfacial behaviors of SiC/PMMA nanocomposites. The acid/base value, contact angles, and FT-IR analysis were performed for the study of surface characteristics of the SiC studied. The thermal stabilities of the SiC/PMMA nanocomposites were investigated by thermogravimetric analysis (TGA). Also the mechanical interfacial properties of the composites were studied in critical stress intensity factor ($K_{IC}$) and critical strain energy release rate ($G_{IC}$) measurements. As a result, the acidically treated SiC (A-SiC) had higher acid value than that of untreated SiC (V-SiC) or basically treated SiC (B-SiC). The acidic solution treatment led to an increase in surface free energy of the SiC, mainly due to the increase of its specific component. Thermal and mechanical interfacial properties of the SiC/PMMA nanocomposites, including initial decomposition temperature (IDT), $K_{IC}$, and $G_{IC}$ had been improved in the acidic treatment on SiC. This was due to the improvement in the interfacial bonding strength, resulting from the acid-base interfacial interactions between the fillers and polymeric matrix.

• International Journal of Contents
• /
• v.9 no.4
• /
• pp.1-10
• /
• 2013

The electroencephalogram (EEG) time series is a measure of electrical activity received from multiple electrodes placed on the scalp of a human brain. It provides a direct measurement for characterizing the dynamic aspects of brain activities. These EEG signals are formed from a series of spatial and temporal data with multiple dimensions. Missing data could occur due to fault electrodes. These missing data can cause distortion, repudiation, and further, reduce the effectiveness of analyzing algorithms. Current methodologies for EEG analysis require a complete set of EEG data matrix as input. Therefore, an accurate and reliable imputation approach for missing values is necessary to avoid incomplete data sets for analyses and further improve the usage of performance techniques. This research proposes a new method to automatically recover random consecutive missing data from real world EEG data based on Linear Dynamical System. The proposed method aims to capture the optimal patterns based on two main characteristics in the coevolving EEG time series: namely, (i) dynamics via discovering temporal evolving behaviors, and (ii) correlations by identifying the relationships between multiple brain signals. From these exploits, the proposed method successfully identifies a few hidden variables and discovers their dynamics to impute missing values. The proposed method offers a robust and scalable approach with linear computation time over the size of sequences. A comparative study has been performed to assess the effectiveness of the proposed method against interpolation and missing values via Singular Value Decomposition (MSVD). The experimental simulations demonstrate that the proposed method provides better reconstruction performance up to 49% and 67% improvements over MSVD and interpolation approaches, respectively.

• Journal of Pharmaceutical Investigation
• /
• v.25 no.1
• /
• pp.19-29
• /
• 1995

The study was carried out to develop useful formulation for omeprazole(OMP) through OMP-ethylendiamine complex(OMPED), and the pharmaceutical properties of formula were tested to find out the difference in vivo behaviors of formulations between the free and complexed OMP. Oral and suppository dosage forms were also formulated and the dissolution profiles and pharmacokinetic parameters were measured to observe the difference in bioavailability between the free and complex form, and the correlation between dissolution rate and bioavailability was evaluated. The results are summarized as follows; In the case of formulation for oral administration, the release of OMP from enteric OMPED pellets was found satisfactory to the requirement standard and no decomposition of OMP in the pellets was found in acidic solution. Therefore the enteric OMPED pellets are anticipated to be a stable formulation. The release of OMP from OMPED tablet with chitosan as excipient and coated with cellulose acetate phthalate was found to be significantly retarded. The results of bioavailability test for OMP and OMPED tablets with lactose-excipient showed that the AUC value of OMP tablet was $116.89\;{\mu}g\;{\cdot}\;min/ml$, that of OMPED tablet was $161.10\;{\mu}g\;{\cdot}\;min/ml$, respectively. The reason why was thought that OMP decomposes more readily in body than OMPED, and the AUC of the tablet with chitosan-excipient and coated with cellulose acetate phthalate was most enhanced. In the case of bioavailability for suppositories with OMP, $OMP-{\beta}\;-cyclodextrin$ complex and OMPED, the AUC of OMPED suppository was most increased. From the above results, it is thought that the more stable and bioavailable oral or rectal dosage forms could be developed by using the OMPED as a potential OMP complex.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.9
• /
• pp.2603-2606
• /
• 2010

Novel soluble triazoleimide oligomers terminated with arylacetylene terminated were synthesized by the Cu(I)-catalysed 1,3-dipolar cycloaddition polymerization of diazides and imide-containing dialkyne. Several molecular weight triazoleimide oligomers were prepared from diazide and dialkyne monomers with different stoichiometric combinations. The curing behaviors of the oligomers were tested by differential scanning calorimetry (DSC). The thermal properties of the cured products were evaluated by DSC and thermogravimetric analysis (TGA). These cured oligomers showed the glass transition temperature of about $225-235^{\circ}C$ and the decomposition temperature (at 5% weight loss) of about $385-393^{\circ}C$ in nitrogen.

• Polymer(Korea)
• /
• v.26 no.4
• /
• pp.501-507
• /
• 2002

In this work, diglycidylether of bisphenol-S (DGEBS) epoxy resin was prepared by alkaline condensation of bisphenol-S (BPS) with epichlorohydrin (ECH) in the presence of NaOH catalyst. The structure of the synthesized DGEBS epoxy resin was confirmed by IR, NMR spectra, and elemental analysis. The curing reaction and glass transition temperature ($T_g$) of DGEBS epoxy resin cured with phthalic anhydride (PA) and tetrahydrophthalic anhydride (THPA) at curing agents were studied by dynamic differential scanning calorimetry (DSC). The thermal stability of the cured specimen was investigated by thermogravimetric analysis (TGA). As a result, the activation energy ($E_a$) of DGEBS/PA system was higher than that of DGEBS/THPA system, whereas $T_g$, initial decomposed temperature (IDT), and decomposition activation energy ($E_t$) of DGEBS/PA were lower than those of DGEBS/THPA. This was probably due to the fact that the crosslinking density of DGEBS/THPA was increased by ring strain of curing agent.