• Journal of Korean Society of Transportation
• /
• v.28 no.1
• /
• pp.25-38
• /
• 2010

In this study, the real on-road driving data were analyzed to draw the various characteristics related to idling of vehicles. The results revealed that the average idling time of a city bus corresponds to 30.9% of the total daily driving time. Among this, for about 21.6% of the total daily driving time, it is available that an engine can be halted while the vehicle stops. It is a daytime when the portion of time, for which idling stop is available, is peak. Due to idling stop, an increase of turnaround was not found throughout this analysis. When a city bus stops at a traffic right, idling periods were long enough to execute the idling stop, during which an engine halts. Whereas, during the idling time for bus stops, the idling periods were not so long enough to execute idling stop. Deceleration periods among the total turnarounds of a city bus occupies about 24.7%, during which, for about 30%, a deceleration maintains for more than four seconds. Thus, using the energy during deceleration period, which then can be recovered from braking energy, it was also found that a hybrid system can be effectively implemented to a city bus.

• Journal of Computational Design and Engineering
• /
• v.2 no.4
• /
• pp.206-217
• /
• 2015

This paper presents a complete S-shape feed rate scheduling approach (CSFA) with confined jerk, acceleration and command feed rate for parametric tool path. For a Non-Uniform Rational B-Spline (NURBS) tool path, the critical points of the tool path where the radius of curvature reaches extreme values are found firstly. Then, the NURBS curve is split into several NURBS sub-curves or blocks by the critical points. A bidirectional scanning strategy with the limitations of chord error, normal/tangential acceleration/jerk and command feed rate is employed to make the feed rate at the junctions between different NURBS blocks continuous. To improve the efficiency of the feed rate scheduling, the NURBS block is classified into three types: short block, medium block and long block. The feed rate profile corresponding to each NURBS block is generated according to the start/end feed rates and the arc length of the block and the limitations of tangential acceleration/jerk. In addition, two compensation strategies are proposed to make the feed rate more continuous and the arc increment more precise. Once the feed rate profile is determined, a second-order Taylor's expansion interpolation method is applied to generate the position commands. Finally, experiments with two free-form NURBS curves are conducted to verify the applicability and accuracy of the proposed method.

• Textile Coloration and Finishing
• /
• v.18 no.5 s.90
• /
• pp.42-47
• /
• 2006

A mixed adsorbent prepared by pyrolysing a mixture of carbon and flyash in 1:1 ratio was tested for its deceleration ability for three different classes of dyes namely, Astrazone Blue FRR(Basic Blue 69), Teflon flue ANL(Acid Blue 125) and Verofix Red(Reactive Red 3GL). Kinetic analyses were carried out at the optimum conditions obtained by the author in the previous studies. The data was fitted with three kinetic model equations. The results showed that the dye uptake mechanism followed the second-order rate expression.

• International Journal of Automotive Technology
• /
• v.5 no.4
• /
• pp.311-319
• /
• 2004

There are many methods to test engine emissions depending on the regulations used such as FTP-75(CYS-75) mode, 10-15 mode and ECE-15 mode. Most of these modes consist of transient conditions such as cranking, rapid acceleration or deceleration modes. In this experimental research, the transient characteristics including cranking and accelerating mode in SI engines were studied to compare pure gasoline with methanol-reformulated fuels for performance and exhaust emissions. The results show that methanol-reformulated fuels have a better emissions reduction rate than that of pure gasoline especially for HC, CO and NOx emissions during cranking mode. The acceleration performances conform to the results of the distillation curve and the CO concentration for RM50 varies slightly in acceleration mode.

• Proceedings of the ESK Conference
• /
• 1997.04a
• /
• pp.107-113
• /
• 1997

In this paper, an interfacing method to control rehabilitation assitance system with bio-signal is proposed. Controlling with EMG signals method has certain advantage on signal-collecting, but has some drawbacks in the function resolution of EMG signals because data-processing process is not efficient. To improve function-resolution and to increase the efficiency of EMG signal interfacing with rehabilitation assistance system, Multi-layer Perception which is highly effective with static signal and hidden-Markov model for dynamic signal resolving are fused together. In proposed method. The direction and average speed of the rehabilitation assitance system are controlled by the trajectory control and estimation of the moving direction result from the fused model. From the experiment, proposed GMM and 2-level MLP hybrid-classifier yielded 8.6% perception-error rate, improving function resolution. New acceleration control method constructed with 3 nested linear filter produced continuous acceleration paths without the information of destination point. Thus, the mass output caused by non- continuous acceleration-deceleration was eliminated. In the simulation, the necessary calculation, in the case of multiplication, was reduced by 11.54%.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.274-279
• /
• 2009

Reduction Gear Box where from productive site uses the gear with power delivery with high mechanical efficiency of power a deceleration and as the mechanical element union product which has the velocity ratio which is various together is produced with the power occurrence motor and leads gets a high driving force is plentifully used. The above occurs from gear drive issue sound Whine, Noise and Vibration as occurring from the rim process which the gear will bite mainly is delivered with the case etc. gear drive whole which leads the axis and the bearing. The productivity falls with the going straight rate decrease which with like this problem point is caused by with rework the problem point where the cost of production rises under improving boil many kinds analyzed the plan and investigates the resultant acceleration sensor which and a frequency analysis system and was made to apply.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.11
• /
• pp.1096-1103
• /
• 2010

This paper proposes CDC (Continuous Damping Control) algorithm and verifies in multi-body dynamic vehicle. In order to distinguish a road profile on driving, waviness calculated by the filtered vertical-accelerations of sprung and unsprung masses is introduced. Sky-hook control is used at a low waviness road and constant damping level control is used at a high waviness road, where the hard damping level is determined by waviness, roll rate, acceleration, and deceleration. The damping levels of ride, anti-roll, anti-squat, and anti-dive modules are calculated by tuning parameters which is dependent upon vehicle velocity. Therefore this high tunable algorithm is useful to improve the ride and handling performance under various driving conditions. In the simulations, tire and dampers are modelled by SWIFT (Short Wavelength Intermediate Frequency Tire) model and 1st order delay model, and results are compared with conventional damper's.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.19 no.38
• /
• pp.85-95
• /
• 1996

자동창고의 설계단계에서 생산율(throughput)을 추정하는 것은 필수적이다. 생산률은 저장/불출 기계의 운행시간에 역비례하므로, 생산율을 추정하기 위해서는 저장/불출 기계의 운행시간을 추정하여야 한다. 이러한 운행시간은 저장랙의 크기, 저장/불출 기계의 가ㆍ감속율, 수직/수평 방향의 최대속도, 그리고 저장정책에 의하여 결정된다. 본 논문에서는 Bozer와 White, Hwang과 Lee의 연구를 기초로 하여, 임의저장 정책하에 저장/불출 기계의 운행시간을 구하는 간단한 모델을 제시한다. 이러한 운행시간 모델은 자동창고의 설계단계에서 유용하게 사용될 수 있다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.1
• /
• pp.49-55
• /
• 2020

Studies on the optimizations of machining processes use two different methods. The first is feed control in real-time by spindle load in a machine tool. The second is feed scheduling in NC code control by material removal rate using a CAD/CAM system. Each approach possesses its respective merits and issues compared to the other. That is, each method can be complementary to the other. The purpose of the study is to improve the productivity of the bulkhead, an aircraft Duralumin structure. In this paper, acceleration or deceleration of cutting tool by spindle load data is achieved using adaptive feed control macro programming in a machine tool.

• Journal of Auto-vehicle Safety Association
• /
• v.6 no.2
• /
• pp.55-60
• /
• 2014

To verify the performance of roadside safety facilities, strength and occupant protection test are performed by evaluation criteria. Strength test use a truck and occupant protection test use a sedan. Strength perfomance is analyzed pass rate by post lateral resistance of the safety barrier. Occupant protection performance is analyzed from THIV(Theoretical Head Impact Velocity) and PHD(Post-impact Head Deceleration) by crash cushion test.