• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.341-345
• /
• 2001

Recently, many examples of practical applications of the motors with reluctance torque, such as IPMSM, RM, etc. are reported. However, the problems of the torque ripple produced by the IPMSM, are also presented. The main reasons of the torque ripple generation are the structural imperfectness of the IPMSM and its control system, such as the cogging torque of the motor, the dead time of inverter, sensors offset, imbalance and non-linearity, and so on. In this paper, authors propose a suppression control method of the torque ripple for IPMSM utilizing the repetitive control with the Fourier transformer and a vibration signal detected by an acceleration sensor attached to the motor frame, considering periodicity of the motor torque ripple. An experimental system to simulate the compliant mechanical frame is constructed, and the effectiveness of the proposed method is confirmed by experimental results.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.4
• /
• pp.27-40
• /
• 1996

This paper proposed a kinematic modeling methodlogy and feedback control system based on kinematics for 2 degrees of freedom of 4-wheeled mobile robot. We assigned coordinate systems to specify the transformation matirx and write the kinematic equation of motion. We derived the actuated inverse and sensed forwared solution for the calculation of actual robot orientation and the desired robot orientation. It is the most significant error and has the largest impact on the motion accuracy. To calculate the WMR position in real time, we introduced the dead-reckoning algorithm and composed two feedback control system that is based on kinematics. Through the simulation result, we compare with the ffedback control system for position control.

• Journal of Industrial Technology
• /
• v.28 no.B
• /
• pp.167-174
• /
• 2008

In this paper, the analysis on type effect of inverter output voltage distortion on the control of an induction motor is discussed. The inverter output voltage is distorted differently from the reference voltage owing to the inverter nonlinear characteristic. The inverter nonlinear characteristic results from the voltage drop, the inherent characteristic of the power semiconductor, and the dead time for preventing the short circuit of the inverter leg. This characteristic distorts the inverter output voltage and then, causes the motor flux estimation error. Although this characteristics do not significantly effect in the general-purpose induction motor control, but significantly effect on the low-speed operation of high performance motor control such as the sensorless vector control.

• Proceedings of the KIEE Conference
• /
• 1994.11a
• /
• pp.322-325
• /
• 1994

Mareel and Bitmead proved the presence of chaotic signal in random noise by applying dead beat control theory to adaptive mechanism. In this paper robust adaptive theory is proposed. With the property of chaotic signal that has order and law, the proposed theory can enhance the control Performance by applying the recursive algorithm that uses dynamic relation which have small correlation. The performance of proposed algorithm is demonstrated with the computer simulation of position control of electric motor. In this simulation, the adaptive low is adopted to control electric motor and the Presence of chaotic signal in feedback signal is proved by using several method such as time series, fourier spectrum phase portrait method.

• Proceedings of the KIEE Conference
• /
• 2007.04a
• /
• pp.113-118
• /
• 2007

In this paper, a new method is proposed for robust proportional- integral - derivative (PID) control that is to ensure specified phase margin and iso - damping property using reduction model. This method is based on the second order plus dead time(SOPDT) reduction model of the high order model. Reduction model used to ensure iso-damping property in the feature frequency. Simulation results gives proof of effectiveness of proposed method.

• Journal of Advanced Marine Engineering and Technology
• /
• v.19 no.1
• /
• pp.71-81
• /
• 1995

In this paper, a new speed control scheme for induction motor drives that regular sampled PWM and harmonic elimination switching pattern over the full range of output speed is presented. The proposed scheme(hybrid scheme) provides three mode and guarantees smooth voltage boost. A detailed description of the scheme, along with the relalization aspect, is described. Moreover, methods of compensating for dead time and optical transmission system of drive signal are proposed and investigated. Finally, experimental investigation of hybrid scheme is presented.

• Journal of fish pathology
• /
• v.25 no.3
• /
• pp.249-256
• /
• 2012

Disease occurrence and dead cell ratio of Porphyra cultivated at Seocheon area were studied. Seaweed samples were collected monthly at 12 cultivating sites of Porphyra from Nov. 2008 to Mar. 2009. Although disease occurrence was low at the beginning of cultivation at the most of collecting sites, the occurrence increased with time. The most common symptom of Porphyra disease in this area was diatom attachment, followed by white rot disease. Licmophora sp. was the most common species of diatom and its attachment was the highest on November, the beginning of cultivation. Although the occurrence ratios of green spot disease and white rot disease were high on November, chytrid disease was increased at the end of cultivation period. Dead cell ratio of Porphyra thalli was different at each study site and cultivating time, but normally the ratio was high at the end of cultivating season. The changes of dead cell ratio could be related to the nutrition supplement and currents, and the more precise reason of dead cell ratio would be revealed by further research related to cultivating environment conditions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.6
• /
• pp.23-30
• /
• 2010

A detailed circuit level model requires a small sampling time to represent high frequency switching behaviors with proper resolution. The small sampling time leads a large execution time to obtain the system analysis results. As the alternative of the detailed circuit model, an averaged PWM switch model was proposed for the rapid system level analysis. There exists a voltage distortion between the reference and output voltage because of non-ideal switching characteristics, such as the dead-time, diode forward voltage drop and conduction resistance. This paper analyzed causes and effects of the voltage distortion. The average inverter model, which reflecting this voltage distortion, is developed for the rapid and accurate analysis of automotive electric drive system in MATLAB/Simulink environment. The rapidity and accuracy of the proposed inverter model is proved through comparison between simulation and experiment.

• International Journal of Control, Automation, and Systems
• /
• v.2 no.3
• /
• pp.279-288
• /
• 2004

This paper presents a novel design for a tubular linear brushless permanent-magnet motor. In this design, the magnets in the moving part are oriented in an NS-NS―SN-SN fashion which leads to higher magnetic force near the like-pole region. An analytical methodology to calculate the motor force and to size the actuator was developed. The linear motor is operated in conjunction with a position sensor, three power amplifiers, and a controller to form a complete solution for controlled precision actuation. Real-time digital controllers enhanced the dynamic performance of the motor, and gain scheduling reduced the effects of a nonlinear dead band. In its current state, the motor has a rise time of 30 ms, a settling time of 60 ms, and 25% overshoot to a 5-mm step command. The motor has a maximum speed of 1.5 m/s and acceleration up to 10 g. It has a 10-cm travel range and 26-N maximum pull-out force. The compact size of the motor suggests it could be used in robotic applications requiring moderate force and precision, such as robotic-gripper positioning or actuation. The moving part of the motor can extend significantly beyond its fixed support base. This reaching ability makes it useful in applications requiring a small, direct-drive actuator, which is required to extend into a spatially constrained environment.

• Journal of Welding and Joining
• /
• v.16 no.6
• /
• pp.68-76
• /
• 1998

A CCD camera with a laser stripe was applied to realized the automatic weld seam tracking. The 3-dimensional information obtained from the vision system made it possible to generate the weld torch path. The adaptive Hough transformation was used to extract laser stripes an to obtain specific weld points. It takes relatively long time to process image on-line control using the basic control using the basic Hough transformation, but it has a tendency of robustness over the noises such as spatter. For this reason, it was complemented with adaptive Hough transformation to have an on-line processing ability for scanning specific weld points. The dead zone, where the sensing of weld line is impossible, was eliminated by rotating the camera with its rotating axis centered at the weld torch. When weld lines were detected, the camera angle was controlled in order to get the minimum image data for sensing of weld lines. Consequently, the image processing time was reduced.