• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.221-222
• /
• 2005

In this paper, application of NN (Neural Network) as a method of pattern discrimination of PD(partial discharge) which occurs at the stator coil of traction motor was studied. For PD data acquisition, three defective models are manufactured such as internal discharge model, slot discharge model and surface discharge model. PD data for recognition were acquired from PD detector and DAQ board which is able to analysis the PD signal and perform the pattern discrimination. Statistical distributions and parameters are calculated to discriminate PD sources. And also these statistical distribution parameters are applied to classify PD sources by BP and has good recognition rate on the discharge sources.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.577-580
• /
• 2005

Surface quality of a micro-processed sample with laser has been investigated by using of scanning confocal microscope(SCM) and atomic force microscope(AFM). Samples are bump electrodes and ITO glass of LCD module used in a mobile phone and a wafer surface scribed by UV laser. A image of $140\times120{\mu}m^2$ is obtained within 1 second by SCM because scan speed of a x-axis and y-axis are 1kHz and 1Hz, respectively. AFM is able to measure correctly hight and width of ITO and scribing depth and width of a wafer with a resolution less than 300 . However, the scan speed is slow and it is difficult to distinguish a surface composed of different nm kinds of materials. Results show that SCM is preferable to obtain a image of a sample composed of different kinds of material than AFM because the intensity of a reflected light from surface is different from each material.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.1
• /
• pp.49-54
• /
• 2009

This paper proposes a new approach to provide RF communication channel and electric power transmission to overcome the weakness of conventional tests, which may cause several problems. When an RF communication device is used to communicate between launch vehicle and launch complex in stead of using harness umbilical, it may draw the simplicity of ground test equipments, cost-saving, and the reduction of test time. In addition, if an RF power transmission device is adopted to supply on-board power of launch vehicle, it can replace expensive on-board batteries, which may be degraded easily by the repeated charging and discharging processes.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1131-1134
• /
• 2003

Unknown parameters of a nonlinear system were estimated using a signal compression method. The estimated parameters were natural frequency and tile damping coefficient. This study applied a algorithm using tile comparison of the cross-correlation coefficient between the impulse response from a model and it from the signal compression method. The impulse through linear element included in a nonlinear system could be obtained by the signal compression method. The unknown parameters of the linear element could be estimated by comparing the Bode plots of system's impulse response with them of model's response. In this study, a LSCM(LabVIEW-Signal-Compression-Method) was developed to identify a nonlinear system. The LSCM consisted of National Instrument's (NI) Data Acquisition (DAQ) Board (Model PCI-1200), a monitoring program using LabVIEW software package, DAQ Signal Accessory Board, and 2nd-order electric circuits. The designed electric circuits consisted of resistors, inductors and capacitors. To evaluate the performance of the LSCM, the response from model with known parameters is compared with the response from the real system using the monitoring program. The results from simulation of experiment showed that the developed LSCM provided a reliable estimation performance.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.4 s.181
• /
• pp.52-59
• /
• 2006

Surface qualities of a micro-processed sample with a pulse laser have been investigated by making use of scanning confocal microscope(SCM) and atomic force microscope(AFM). Samples are bump electrodes and ITO glass of LCD module used in a mobile phone and a wafer surface scribed by UV laser. A image of $140{\times}120{\mu}m^2$ is obtained within 1 second by SCM because scan speed of a x-axis and y-axis are 1kHz and 1Hz, respectively. AFM is able to correctly measure the hight and width of ITO, and scribing depth and width of a wafer with a resolution less than 300nm. However, the scan speed is slow and it is difficult to distinguish a surface composed of different kinds of materials. Results show that SCM is preferable to obtain a image of a sample composed of different kinds of material than AFM because the intensity of a reflected light from the surface is different for each material.

• Journal of Biosystems Engineering
• /
• v.43 no.4
• /
• pp.426-439
• /
• 2018

Purpose: To continuously monitor soil and climatic properties, a data acquisition system (DAQ) was developed and tested in plum farms (Gyewol-ri and Haechang-ri, Suncheon, Korea). Methods: The DAQ consisted of a Raspberry-Pi processor, a modem, and an ADC board with multiple sensors (soil moisture content (SEN0193), soil temperature (DS18B20), climatic temperature and humidity (DHT22), and rainfall gauge (TR-525M)). In the laboratory, various tests were conducted to calibrate SEN0193 at different soil moistures, soil temperatures, depths, and bulk densities. For performance comparison of the SEN0193 sensor, two commercial moisture sensors (SMS-BTA and WT-1000B) were tested in the field. The collected field data in Raspberry-Pi were transmitted and stored on a web server database through a commercial communications wireless network. Results: In laboratory tests, it was found that the SEN0193 sensor voltage reading increased significantly with an increase in soil bulk density. A linear calibration equation was developed between voltage and soil moisture content depending on the farm soil bulk density. In field tests, the SEN0193 sensor showed linearity (R = 0.76 and 0.73) between output voltage and moisture content; however, the other two sensors showed no linearity, indicating that site-specific calibration is important for accurate sensing. In the long-term monitoring results, it was observed that the measured climate temperature was almost the same as website information. Soil temperature information was higher than the values measured by DS18B20 during spring and summer. However, the local rainfall measured using TR 525M was significantly different from the values on the website. Conclusion: Based on the test results obtained using the developed monitoring system, it is thought that the measurement of various parameters using one device would be helpful in monitoring plum growth. Field data from the local farm monitoring system can be coupled with website information from the weather station and used more efficiently.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2019.05a
• /
• pp.271-274
• /
• 2019

In this paper, we proposed a detailed address acquisition scheme for automatically collecting data of a web page in a frame that is difficult to access by a general web access method. Using the Python language and the Beautiful Soup library, which can utilize the proposed address resolution technique and the HTML selector, we were able to automatically collect all the bulletin board text data written in several pages. By using the proposed method, we can collect large amount of data automatically by Python web scraping program for web pages of any form of address, and we expect that it can be used for big data analysis.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.2
• /
• pp.149-156
• /
• 2011

There is much information of equipment in shop floor because the manufacturing processes are different as the equipment within the manufacturing process is varied. To provide effective process information to MES and other production systems, the DAS requires an equipment monitoring system that takes into account the characteristics of the equipment on the shop floor. In this study, we proposed some methods for collecting the required information about various equipments on a shop floor. The equipments such as CNC can be interfaced with the DAS by using a PLC-based method and a sensor-based interface board can be used to interface general equipments. The proposed methods can be used to collect information on the shop floor in real-time. Moreover these methods are very adaptive and can be easily modified according to the changes made to the shop floor. The information about a real shop floor acquired by employing these methods is saved in a database and the can be provided to a supervisor and MES so that they are aware of the status of the shop floor.

• Korean Journal of Remote Sensing
• /
• v.23 no.2
• /
• pp.137-144
• /
• 2007

In KORDI (Korea Ocean Research and Development Institute), the KOSC (Korea Ocean Satellite Center) construction project is being prepared for acquisition, processing and distribution of sensor data via L-band from GOCI (Geostationary Ocean Color Imager) instrument which is loaded on COMS (Communication, Ocean and Meteorological Satellite); it will be launched in 2008. Ansan (the headquarter of KORDI) has been selected for the location of KOSC between 5 proposed sites, because it has the best condition to receive radio wave. The data acquisition system is classified into antenna and RF. Antenna is designed to be $\phi$ 9m cassegrain antenna which has 19.35 G/T$(dB/^{\circ}K)$ at 1.67GHz. RF module is divided into LNA (low noise amplifier) and down converter, those are designed to send only horizontal polarization to modem. The existing building is re-designed and arranged for the KOSC operation concept; computing room, board of electricity, data processing room, operation room. Hardware and network facilities have been designed to adapt for efficiency of each functions. The distribution system which is one of the most important systems will be constructed mainly on the internet. and it is also being considered constructing outer data distribution system as a web hosting service for offering received data to user less than an hour.

• Journal of the Korea Society of Computer and Information
• /
• v.25 no.7
• /
• pp.1-8
• /
• 2020

In this paper, we present an implementation of high speed image data transfer using XDMA for a video signal generation / acquisition device developed as a military test equipment. The technology proposed in this study obtains efficiency by replacing the method of copying data using the system buffer in the kernel area with the transmission and reception through the DMA engine in the FPGA. For this study, the device was developed as a PXIe platform in consideration of life cycle, and performance was maximized by using a low-cost FPGA considering mass productivity. The video I/O board implemented in this paper was tested by changing the AXI interface clock frequency and link speed through the existing memory copy method. In addition, the board was constructed using the DMA engine of the FPGA, and as a result, it was confirmed that the transfer speed was increased from 5~8Hz to 140Hz. The proposed method will contribute to strengthening defense capability by reducing the cost of device development using the PXIe platform and increasing the technology level.