• Journal of Korean Society of Transportation
• /
• v.27 no.5
• /
• pp.113-124
• /
• 2009

This paper suggests a new approach for providing information for driver safety at signalized intersections. Particularly dangerous situations at signalized intersections such as red-light violations, accelerating through yellow intervals, red-light running, and stopping abruptly due to the dilemma zone problem are considered in this study. This paper presents the development of a dangerous vehicle determination algorithm by collecting real-time vehicle speeds and times from multiple point detectors when the vehicles are traveling during phase-change. For an evaluation of this algorithm, VISSIM is used to perform a real-time multiple detection situation by changing the input data such as various inflow-volume, design speed change, driver perception, and response time. As a result the correct-classification rate is approximately 98.5% and the prediction rate of the algorithm is approximately 88.5%. This paper shows the sensitivity results by changing the input data. This result showed that the new approach can be used to improve safety for signalized intersections.

• Journal of Auto-vehicle Safety Association
• /
• v.11 no.2
• /
• pp.17-22
• /
• 2019

This paper describes the tracking algorithm performance evaluation for autonomous vehicle using a safety envelope based path. As the level of autonomous vehicle technologies evolves along with the development of relevant supporting modules including sensors, more advanced methodologies for path generation and tracking are needed. A safety envelope zone, designated as the obstacle free regions between the roadway edges, would be introduced and refined for further application with more detailed specifications. In this paper, the performance of the path tracking algorithm based on the generated path would be evaluated under safety envelop environment. In this process, static obstacle map for safety envelope was created using Lidar based vehicle information such as current vehicle location, speed and yaw rate that were collected under various driving setups at Seoul National University roadways. A level of safety was evaluated through CarSim simulation based on paths generated with two different references: a safety envelope based path and a GPS data based one. A better performance was observed for tracking with the safety envelop based path than that with the GPS based one.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.4
• /
• pp.382-388
• /
• 2014

This study selected five observational stations in the normal direction of Jinu-do(island) shoreline and observed water temperature, electrical conductivity and pressure from March, 2012 to January, 2013(about 11 months) and attempted to see the variation characteristics of ground watertable. This study wants to know : 1) External environment force factors(tide, climate, wave etc.) affecting ground watertable variation through time series and correlation analysis. 2) Spatial variations of ground watertable and electrical conductivity change by storm event. First, we found that the station at the intertidal zone was strongly affected by wave and tide level and the stations at sand dune and vegetation zone was affected by precipitation and tide level through time series data and correlation analysis. Second, during the storm event, we found that ground watertable and electrical conductivity are stabilized at the start line of sand dune and vegetation zone and transition zone between freshwater layer and seawater layer exists in the experiment area and is about 50~70 m from coastline of the south side of Jinu-do(island).

• The Journal of the Korea Contents Association
• /
• v.22 no.2
• /
• pp.116-124
• /
• 2022

After the death of Min-sik Kim in Asan, South Chungcheong Province in September 2019, awareness of the school zone has been increasing, and the traffic law is being revised continuously. However, despite these efforts, the number of traffic accidents among children has not decreased significantly. This indicates the need for a new direction considering the behavioral characteristics of children and the traffic environment. Therefore, this study identified the current status and problems of school zones through case analysis of school zones in Korea. In addition, we analyzed the Vision Zero policy, the concept of Home Zone, and engineering-oriented road design cases and operation methods in Sweden, an advanced country in traffic safety. In addition, the cases of the two countries were compared and organized focusing on the basic principles of disaster prevention design. The purpose of this study is to suggest the direction of design and policy to improve school zone problems in Korea. Through this, it is expected that the results of this study will be used as data for future research development for the reduction of school zone fatalities in Korea.

• Journal of Energy Engineering
• /
• v.25 no.4
• /
• pp.103-109
• /
• 2016

Polyethylene pipes has useful benefits which are anti-corrosive and flexible material, so it is used to gas pipes but also class 3 water pipes of nuclear power plant, process pipes of petrochemical plant and chemical plant. So the usage of polyethylene pipes is widely increased. But it has been limited for the usage of polyethylene, because it can not be directly detected to fusion joints by using non destructive evaluation. Polyethylene pipes are connected by two methods, one is butt fusion and the other is electrofusion. Butt fusion is widely used to connecting the pipes. It is proposed to method for determining the reliability of joints in this study that is detection of the melt flow zone at fusion joints. In this study, middle density polyethylene is used, outside diameter of the test specimen is 225mm and thickness is 20.5mm. Speed of ultrasonic of this test specimen is 2,200m/s. Test specimens were fabricated by varying the heating time which means from 0% to 130% applying time through heating plate to polyethylene for detecting melt flow zone. Also 4 additional test specimens were made, one was made that not scrapping attached surface of pipes but applying 100% of the proper heating time and the others were made to include of soil, gravel and vinly tape paper at fusion joints, that were also applied 100% of proper heating time. Ultrasonic testing to measure the melt flow zone of 20 test specimens was conducted by using 3.5MHz and 5.0MHz ultrasonic probes and melt flow zone measuring was conducted to three times at different point to one specimen. To differentiate the melt flow zone signal, post image processing was equally conducted to all test results and image levels, contrast, sharpen, threshold were adopted to all teat results and the test results were displayed gray scale. From the results, for the shorter heating times the reflection area of multiple echo have been increased, so the data was obtained from the position where it can be eliminated as much as possible. At 80% of proper heating time(168 sec.), the signal of melt flow zone was obtained clearly, so measuring could be conducted. From 7% of proper heating time(15 sec.) to shorter heating times. we could not obtain the signal because test specimen was not fused. From the result, we can verify that measuring of melt flow zone by using phased array ultrasonic imaging method is possible. And we can verify to complete and incomplete butt fusion by measuring the melt flow zone.

• Geosystem Engineering
• /
• v.21 no.6
• /
• pp.326-334
• /
• 2018

Underground water-sealed gas storage caverns have become the primary method for strategic storage of LPG. Previous studies of excavation blasting effects on large-scale underground water-sealed gas storage caverns are rare at home and abroad. In this paper, the blasting excavation for underground water-sealed propane storage caverns in Yantai was introduced and field tests of blasting vibration were carried out. Field test data showed that the horizontal radial velocity had a major controlling effect in the blasting vibration and frequencies would not cause the vibration velocity concentration effects. In terms of the influence of blasting vibration on adjacent caverns, the dynamic finite element model in LS-DYNA soft was established, whose reliability was verified by field test data. The numerical results indicated the near-blasting side was primary zone for the structural failure and tensile failure tended to occur in the middle of the curved wall on the near-blasting side. Meanwhile, the safety criterions for adjacent caverns based on stress wave theory and according to statistic relationship between peak effective tensile stress and peak particle velocities were obtained, respectively. Finally, with Safety Regulations for Blasting in China (GB6722-2014) taken into account, a final safety criterion was proposed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.2
• /
• pp.189-194
• /
• 2007

Recently, as consumer's claim fur car safety is increased, quality inspection method fur welding zone is strengthened. Therefore, from the methods that depend on welding zone bead shape size of seat frame in macrography or passive examination, the quality control by whole recording inspection is required. In this study, the system that is measuring automatically if worker checks welding bead fur quality inspection of seat frame is developed using LabVIEW. If the quality standard for the bead width and length of welding zone is inputted, the system measures automatically whether welding zone is bead length or bead width. Measured data is preserved by points and quality recording of welding zone is stored. The car seat きme welding zone is applied and experimented. The results gave good influence o9 the quality control of work efficiency.

• Journal of the Korean Society of Safety
• /
• v.26 no.5
• /
• pp.41-45
• /
• 2011

The fire event occurred in fire proof zone often causes serious electrical problems such as shorts, ground faults, or open circuits in nuclear power plants. These would be directed to the loss of safe shutdown capabilities performed by safety related systems and equipments The fire event can treat the basic design principle that safety systems should keep their functions with redundancy and independency. In case of a cable fire, operators can not perform their mission properly and can misjudge the situation because of spurious operation, wrong indication or instrument. These would deteriorate the plant capabilities of safety shutdown and make disastrous conditions. In this paper, the cables of the representative nuclear power plant in korea is selected and the cable functional failure temperature by exposed fire using Cable Response to Live Fire(CAROLFIRE) is studied. It is expected that the results are very useful to know the cable failure temperature by exposed fire. We confirmed the safety and integrity of the cable by exposed fire and those results will use the based data of cable exposed fire characteristics.

• Journal of the Korean Society of Safety
• /
• v.35 no.3
• /
• pp.79-85
• /
• 2020

Ahn-heung Proving Ground(APG) of Agency for Defense Development(ADD) is the only weapon test site which has been performing firing tests for many kinds of missile, artillery and ammunition. APG has been performing the firing tests of so many times every year. The tests related to missiles, artillery and ammunitions cover 80% among the quantity of annual test events. The target area of many kinds of missile, artillery and ammunition is on the sea. Therefore, APG has its marine firing ranges which were approved by the ministry of Defense. Both weapons and ships can run into each other on the sea. APG has to monitor and detect the positions of the ships in the specific dangerous zone on the sea. The positions of the ships are detected by Scanter 2001 radar and GPS100 detection radar. Evading the time period when the ships appear very often on the sea may be a good solution to keep the maritime safety. And evading the place where the ships appear very often on the sea may be a good solution as well. This paper is to analyze the ships' distribution characteristics of marine firing range, which are to raise the efficiency of many kinds firing tests which have been performed in APG of ADD. Ship distribution data from February 2014 to December 2016 were used in this paper. Ship distribution was analyzed with monthly data, seasonal data and etc. The number of the ships in approved sea area is higher in the morning than in the afternoon, and in fall than other seasons, and from August to November, and below 0.5 m in the hight of wave. Using the these conditions, we can raise the test efficiency of many kinds firing tests and guarantee maritime safety. The number of the ships in approved sea area is entirely unrelated to visibility of the sea. The time period when the number of the ships are high on the sea is morning. The season when the number of the ships are comparatively high on the sea is fall. APG of ADD could raise the efficiency of the firing tests and improve the maritime safety, using the analysis results of the characteristics on the ship distribution.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.9 no.2
• /
• pp.209-218
• /
• 2017

Sea ice is the main factor affecting the safety of the Arctic engineering. However, traditional numerical methods derived from classical continuum mechanics have difficulties in resolving discontinuous problems like ice damage. In this paper, a non-local, meshfree numerical method called "peridynamics", which is based on integral form, was applied to simulate the interaction between level ice and a cylindrical, vertical, rigid structure at different velocities. Ice in the simulation was freshwater ice and simplified as elastic-brittle material with a linear elastic constitutive model and critical equivalent strain criterion for material failure in state-based peridynamics. The ice forces obtained from peridynamic simulation are in the same order as experimental data. Numerical visualization shows advantages of applying peridynamics on ice damage. To study the repetitive nature of ice force, damage zone lengths of crushing failure were computed and conclude that damage zone lengths are 0.15-0.2 times as ice thickness.