• Nuclear Engineering and Technology
• /
• v.55 no.10
• /
• pp.3787-3800
• /
• 2023

Reactivity Initiated Accident (RIA) scenarios require special attention using advanced simulation techniques due to their complexity and importance for nuclear power plant (NPP) safety. While the conservative approach has traditionally been used for safety analysis, it may lead to unrealistic results which calls for the use of best estimate plus uncertainty (BEPU) approach, especially with the current advances in computational power which makes the BEPU analysis feasible. In this work an Uncontrolled Control Element Assembly (CEA) Withdrawal at Full Power accident scenario is analyzed using the BEPU approach by loosely coupling the thermal hydraulics best-estimate system code (RELAP5/SCDAPSIM/MOD3.4) to the statistical analysis software (DAKOTA) using a Python interface. Results from the BEPU analysis indicate that a realistic treatment of the accident scenario yields a larger safety margin and is therefore encouraged for accident analysis as it may enable more economic and flexible operation.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.9
• /
• pp.1006-1015
• /
• 2005

We investigated the effect of hydroxyl radicals on the photolysis of triclosan (TCS), which is a potent broad-spectrum antimicrobial agent. TCS degradation during the initial reaction time of 5 min followed a pseudo-first order kinetic model ai all light intensities at a wavelength of 365 nm and at the low light intensities at a wavelength of 254 nm. The photodegradation rate significantly increased with decreasing wavelength and increasing the UV intensities. The activity of hydroxyl radicals was suppressed when methanol was used as the solvent instead of water. An increase in the photon effect was observed when the UV intensity was higher than $5.77{\times}10^{-5}$ einstein $L^{-1}min^{-1}$ at 254 nm, and lower than $1.56{\times}10^{-4}$ einstein $L^{-1}min^{-1}$ at 365 nm. The quantum yield efficiency for the photolysis of TCS was higher at 365 nm than at 254 nm among the above mentioned UV intensities. Dibenzodichloro-p-dioxin (DCDD) and dibenzo-p-dioxin were detected as intermediates at both UV intensities of $1.37{\times}10^{-4}$ and $1.56{\times}10^{-4}$ einstein $L^{-1}min^{-1}$ at 365 nm. Dichlorophenol and phenol were also detected in all cases. Based on our findings, we presented a possible mechanism of TCS photolysis.

• Asian Journal of Turfgrass Science
• /
• v.21 no.1
• /
• pp.69-79
• /
• 2007

Incorporating herbicides application into a fertilization program has several benefits including saving time and reducing traffics on the lawn. Premixed products of fertilizers and herbicides are commonly known as Weed & Feed in the lawn-care industry. To compare Weed & Feed with separate applications of fertilizers and herbicides on a Kentucky bluegrass (Poa pratensis L.) lawn, a Weed & Feed 28-3-3, containing 0.64% 2,4-D, 0.31% MCPP, and 0.03% dicamba of active ingredients, was used in this study. The first application was in May, with the second in June or Sept. Herbicides in forms of 2,4-D (LV-4, 4EC), MCPP (4EC), and dicamba (Clarity, 4EC) were applied at rates equal to the amounts in Weed & Feed or at half of the rates. The dominant weed in both locations was common dandelion (Taraxacum officinale Weber.) in 2005 and 2004. A secondary weed was Canada thistle (Cirsium arvense (L.) Scop.) in 2004 and broadleaf plantain (Plantago major L.) in 2005. When applied in May and June, fertilizer plus full rate of herbicides treatment achieved 112.3 and 83.7 days of acceptable turf quality in 2004 and 2005, respectively. During the same period, Weed & Feed resulted in 58.7 and 24.3 days of acceptable turf quality, respectively. Our study showed that Weed & Feed was generally as effective in weed control as the same amount of fertilizer plus half rates of herbicides sprayed although results may vary due to the timing of application. Fertilizer plus full rates of herbicides provided the same or better results of weed control than Weed & Feed.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.6
• /
• pp.642-650
• /
• 2005

This research investigates the effects of adding oxidants such as $Fe^0$, $Fe^{2+}$, and ${S_2O_8}^{2-}$ in the sonolysis of 1,4-D. Results indicate that the degradation could be divided into two steps (initiation and acceleration) kinetically. The initial portion agreed with zero-order expression, while the second portion could be fitted with pseudo first-order expression. In the presence of ${HCO_3}^-$, as a radical scavenger, the degradations of 1,4-D and TOC were suppressed, indicating that OH radical is an important factor in the sonolysis. The overall degradation efficiency of 79.0% in the sonolysis was achieved within 200 minutes. While $Fe^0$, $Fe^{2+}$, and ${S_2O_8}^{2-}$ were individually combined with sonication, the degradation efficiency of 1,4-D increased 18.6%, 19.1%, and 16.5% after 200 min, respectively. The addition of oxidants not only changed the kinetic model from zero to pseudo first order at initiation step, but also increased the rate constants in the acceleration step. The addition of oxidants in the sonolysis of 1,4-D also improved the mineralization of 1,4-D, however, the effect of adding oxidants on the rate increase was similar regardless of the oxidants.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.10
• /
• pp.1114-1122
• /
• 2005

This research investigates the effects of sonication mode, reaction temperature and volume on sonolysis of 1,4-dioxane in order to increase the degradation efficiency and kinetics. The degradation efficiency in case with pulse mode was about 10 % higher than that in case with continuous mode. The degradation profiles in both cases, which were performed without the control of reaction temperature and in 1000 mL, were composed of three steps. However, 1,4-D was mainly degraded in the initiation step as the first portion and the acceleration step as the second portion. The initial step agreed with zero-order expression well, while the acceleration step could be fitted with pseudo 1st-order expression. The kinetic model in case with $5^{\circ}C$ and 300 mL conformed to pseudo 1st-order, while that in cases with $10^{\circ}C$ to $40^{\circ}C$ agreed with zero-order expression. The degradation efficiency and profile of 1,4-D in the experiment with $20^{\circ}C$ and 300 mL was higher and simpler than that in case with $20^{\circ}C$ and 1000 mL. The reaction temperature and volume influence bubble intensity, which was produced in sonication. The increase of bubble intensity induced to augment the production of OH radical in sonication.

• Spatial Information Research
• /
• v.21 no.5
• /
• pp.33-41
• /
• 2013

Recently, the number of disasters has been seriously increasing. The total damages by the natural or man-made disasters during the past years resulted in tremendous fatalities and recovery costs. It is necessary to have efficient emergency evacuation management which is concerned with identifying evacuation route, and the estimation of evacuation and clearance times. An emergency evacuation model is important in identifying critical locations, and developing various evacuation strategies. In that existing evacuation models have focused on route analysis for indoor evacuation, there are only a few models for areawide emergency evacuation analysis. Therefore, we developed a mesoscopic model by using Cube Avenue and performed evacuation simulation, targeting road network in City of Fargo, North Dakota. Consequently, a mesoscopic model developed in this study is used to carry out dynamic analysis using network and input variable of existing travel demand model. The results of this study show that the model is an appropriate tool for areawide emergency evacuation analysis to save time and cost. Henceforth, the results of this study can be applied to develop a disaster evacuation model which can be used for a variety of disaster simulation and evaluation based on scenarios in the local metropolitan area.

• Asian-Australasian Journal of Animal Sciences
• /
• v.22 no.7
• /
• pp.1016-1025
• /
• 2009

Two experiments were conducted to determine energy and nutrient digestibility in four sources of distillers dried grains with solubles (DDGS) produced from corn and fed to growing pigs. The objective was to test the hypothesis that energy and nutrient digestibility in DDGS does not vary if samples are procured from ethanol plants that use similar production technologies and use corn that is grown within a narrow geographical area. The four sources of DDGS that were used were procured from ethanol plants that were less than 10 yr old and located within 250 km of each other. In Exp. 1, five growing barrows (initial BW = 71.4 kg) that were fitted with a T-canula in the distal ileum were allotted to a 5${\times}$5 Latin square design and used to measure apparent (AID) and standardized (SID) ileal digestibility of AA in the four sources of DDGS. Results of this experiment showed that the SID of CP and all AA except Cys and Pro were greater (p<0.05) in two of the DDGS sources than in the other two sources. Exp. 2 was conducted to measure the concentration of DE and ME and the apparent total tract digestibility (ATTD) of energy, N, P, ether extract, NDF, and ADF in corn and in the same four sources of DDGS as used in Exp. 1. Five pigs (initial BW = 29.7 kg) that were placed in metabolism cages and allotted to a 5${\times}$5 Latin square design were used. Results of Exp. 2 showed that the average DE and ME in DDGS were 4,072 and 3,750 kcal/kg DM, respectively, which was less (p<0.01) than the DE and ME in corn (4,181 and 4,103 kcal/kg DM, respectively). The average ATTD for P in DDGS was 56.1%, which was greater (p<0.01) than the ATTD for P in corn (31.9%). The ATTD for ADF in DDGS was also greater (p<0.05) than in corn, but the ATTD for ether extract and NDF were greater (p<0.05) in corn than in DDGS. It is concluded that energy and nutrient digestibility vary among sources of DDGS even when the DDGS is procured from ethanol plants that use corn grown within a narrow geographical region. Thus, factors other than corn growing region are responsible for the variability of energy and nutrient digestibility in DDGS.

• Korean Journal of Food Science and Technology
• /
• v.16 no.4
• /
• pp.429-436
• /
• 1984

To expand the utility of barley the experiments on the extrusion characteristics of barley flour for snack processing were carried out and the effects of the extrusion conditions on the quality of the extrudates were investigated. The optimum moisture content of barley flour for snack processing was 20%. The moisture content and the density of the extrudates decreased with increasing extrusion temperature and decreasing die size. The die swell ranged from 0.98 to 2.18 according to various extrusion conditions and decreased with increasing temperature above $150^{\circ}C$. The lightness, redness and yellowness increased at higher temperature. The water absorption index and the water solubility index showed their maximum values at $180^{\circ}C$.The gelatinization degree of the extrudates increased with increasing temperature. The fracture fore, Young's modulus and maximum fiber stress decreased, but the deformation to fracture increased, with increasing temperature and decreasing die size. The yield force in puncture test showed lower values at higher temperature. The size and the fraction of the air cells increased with increasing temperature and decreasing die size. The optimum extrusion conditions of barley for snack processing were at the temperature of $180^{\circ}C$, with the die size of 4.5mm when processed at 160 rpm.

• Journal of Korean Society for Quality Management
• /
• v.18 no.2
• /
• pp.18-24
• /
• 1990

The location of inspection stations is a significant component of production systems. In this paper, a prototype expert system is designed for deciding the optimal location of inspection stations. The production system is defined as a single channel of n serial operation stations. The potential inspection station can be located after any of the operation stations. Nonconforming units are generated from a compound binomial distribution with known parameters at any given operation station. Traditionally Dynamic programming, Zero-one integer programming, or Non-linear programming techniques are used to solve this problem. However a problem with these techniques is that the computation time becomes prohibitively large when t be number of potential inspection stations are fifteen or more. An expert system has the potential to solve this problem using a rule-based system to determine the near optimal location of inspection stations. This prototype expert system is divided into a static database, a dynamic database and a knowledge base. Based on defined production systems, the sophisticated rules are generated by the simulator as a part of the knowledge base. A generate-and-test inference mechanism is utilized to search the solution space by applying appropriate symbolic and quantitative rules based on input data. The goal of the system is to determine the location of inspection stations while minimizing total cost.

• International Journal of Concrete Structures and Materials
• /
• v.7 no.1
• /
• pp.51-59
• /
• 2013

The use of light-gauge steel framing in low-rise commercial and industrial building construction has experienced a significant increase in recent years. In such construction, the wall framing is an assembly of cold-formed steel (CFS) studs held between top and bottom CFS tracks. Current construction methods utilize heavy hot-rolled steel sections, such as steel angles or hollow structural section tubes, to transfer the load from the end seats of the floor joist and/or from the load-bearing wall studs of the stories above to the supporting load-bearing wall below. The use of hot rolled steel elements results in significant increase in construction cost and time. Such heavy steel elements would be unnecessary if the concrete slab thickening on top of the CFS wall can be made to act compositely with the CFS track. Composite action can be achieved by attaching stand-off screws to the track and encapsulating the screw shank in the deck concrete. A series of experimental studies were performed on full-scale test specimens representing concrete/CFS flexural elements under gravity loads. The studies were designed to investigate the structural performance of concrete/CFS simple beams and concrete/CFS continuous headers. The results indicate that concrete/CFS composite flexural elements are feasible and their structural behavior can be modeled with reasonable accuracy.