• Journal of Korean Society for Quality Management
• /
• v.23 no.4
• /
• pp.128-147
• /
• 1995

An accelerated life testing(ALT) for aluminum electrolytic capacitors is conducted and analyzed. A testing equipment, which consists of part fixtures, relay board, controller, video bridge and microcomputer, is made for the ALT. Load factors are temperature with four levels and voltage with three levels. Base on 'optimized 4:2:1 plan', 2,000 electrolytic capacitors are allocated at 12 experimental conditions(; 4 levels of temperature ${\times}3$ levels of voltage), and the ALT is conducted. From the experimental results, an acceleration model is derived and acceleration factors are estimated. A discussion on the experimental results is included.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.1289-1293
• /
• 2010

A slipring or FORJ are usually adopted in order for power supply of Geo-centrifuge and input/output data acquisition. Since using slipring causes quite a lot electrical noise, an optical communication using FORJ becomes more general for data acquisition. Such data acquisition devices, however, require frequent maintenance and replacement due to deterioration by long term usage. DICT has set up a real-time wireless date acquisition system using wireless communication technology instead of FORJ. The system enables a remote measurement at any inertial acceleration field up to 100g level and provides as same performance as FORJ. The priority of this system is to use a normal modem substituting a special FORJ.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.1328-1332
• /
• 2010

The enlargement of existing tunnels is required to cope with problems related to traffic congestion. Sometimes, the tunnel traffic must be maintained through existing tunnels during their reconstruction due to non-availability of detours. And excavation by drill and blasting is desired for widening a hard rock tunnel. In this case, the road must be closed for some period for blasting through analyzing of traffic volume. In this paper, a case study on some traffic countermeasures for tunnel enlargement by blasting was performed. And the traffic flow characteristics of some tunnels in domestic main city were analyzed.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2009.09a
• /
• pp.6-17
• /
• 2009

The present paper addresses development of a GTT NO96 membrane type 170K m3 LNG carrier targeted to operate in moderate ice infested seas including Baltic Sea, Sakhalin port of Sea of Okhotsk, Murmansk port of Barents Sea, etc. Critical design issues are covered in detail to meet the requirements coming from the missioned operation conditions comprising low design ambient temperature, harsh wave conditions, stringent environmental protection policies, etc.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.04a
• /
• pp.191-196
• /
• 2014

In the evaluation of measured noise data, tolerance shall be decided based on the uncertainty. The uncertainty has frequency variations due to the different standard deviations at each frequency. Therefore, tolerance shall be differently decided for each frequency with the same confidence probability. In the report, the evaluation method considering the frequency variation of uncertainty will be introduced. From the approach, considering the actual noise distribution characteristics of the ships, the tolerance shall be decided for each frequency with the same probability, but the overall averaged value shall be kept to the value designated in each notation.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.75-78
• /
• 2004

Engine power cylinder parts are faced with more severe wear and friction environment. For instance, emission gas recirculation (EGR), one of the most valid technologies related to emission legislation, is known to accelerate wear of piston ring and cylinder liner. Therefore, advanced materials and surface treatments have been developed and adopted successively so that a need exists for an accurate and repeatable friction and wear bench test for various combination of piston ring and cylinder liner that more closely relates to engine test result. This paper introduces accelerative bench wear test method for piston ring and cylinder liner, presents the experimental result of friction and wear properties of piston ring surface treatments that noticed in substitution for hard chrome plating.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.700-705
• /
• 2002

The welding distortion of a hull structure in the shipbuilding industry is inevitable at each assembly stage. The geometric inaccuracy caused by the distortion tends to preclude the introduction of automation and mechanization and needs the additional man-hours for the adjusting work at the following assembly stage. To overcome this problem, a distortion control method should be applied. For this purpose, it is necessary to develop an accurate prediction method which can explicitly account for the influence of various factors on the welding distortion. In order to minimize the weld-induced angular distortion in thick weldments, this paper proposes the optimum groove design for various plate thicknesses as the distortion control method. The validity of this method has been substantiated by a number of numerical simulations and experiments.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.1382-1387
• /
• 2010

A 3D FEM numerical analysis was performed to observe the changes of supporting system of a old 1-lane tunnel when it is enlarged to 2-lane, 3-lane and 4-lane. The standard Type-III supporting pattern was applied to the new tunnel because the ground was assumed as Type-III. The observation was carried out at the middle supporting system of the old 1-lane tunnel alignment. The results shows that the changes of old tunnel supporting system began when the new tunnel was excavated at 2D(D is the equivalent diameter of 1-lane tunnel) behind of the observation place and became very rapid from 1D.

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2556-2558
• /
• 1999

We present voltage-source inverter for variable speed of washing machine. In the case of previous washing machines only on/off contol of motor was satisfied but these days the desire of customers moves to more silent and energy saving machine. Therefore many white goods manufacturers consider variable driving methods of motor. Nowadays variable speed Induction motors powered by inverters are becoming more and more popular. In this paper the principles of constant V/F control of Induction motor used in washing machine and space vector PWM technique are reviewd. Implementation issues such as command voltage generation, switching pattern determination, speed and power measurement are also presented. Experimental results are included in the end of the paper.

• International Journal of Concrete Structures and Materials
• /
• v.19 no.1E
• /
• pp.3-9
• /
• 2007

This paper presents a numerical procedure for analyzing the joints between precast post-tensioned segments. A computer program for the analysis of reinforced concrete structures was run for this problem. Models of material nonlinearity considered in this study include tensile, compressive and shear models for cracked concrete and a model for reinforcing steel with smeared crack. An unbonded tendon element based on the finite element method, that can describe the interaction between the tendon and concrete of prestressed concrete member, was experimentally investigated. A joint element is newly developed to predict the inelastic behavior of the joints between segmental members. The proposed numerical method for the joints between precast post-tensioned segments was verified by comparison of its results with reliable experimental results.