• Imaging Science in Dentistry
• /
• v.54 no.1
• /
• pp.43-48
• /
• 2024

Purpose: Oral hygiene, maintained through plaque control, helps prevent periodontal disease and dental caries. This study was conducted to examine the accuracy of plaque detection with an intraoral scanner(IOS) compared to images captured with an optical camera. Materials and Methods: To examine the effect of color tone, artificial tooth resin samples were stained red, blue, and green, after which images were acquired with a digital single-lens reflex (DSLR) camera and an IOS device. Stained surface ratios were then determined and compared. Additionally, the deviation rate of the IOS relative to the DSLR camera was computed for each color. In the clinical study, following plaque staining with red disclosing solution, the staining was captured by the DSLR and IOS devices, and the stained area on each image was measured. Results: The stained surface ratios did not differ significantly between DSLR and IOS images for any color group. Additionally, the deviation rate did not vary significantly across colors. In the clinical test, the stained plaque appeared slightly lighter in color, and the delineation of the stained areas less distinct, on the IOS compared to the DSLR images. However, the stained surface ratio was significantly higher in the IOS than in the DSLR group. Conclusion: When employing IOS with dental plaque staining, the impact of color was minimal, suggesting that the traditional red stain remains suitable for plaque detection. IOS images appeared relatively blurred and enlarged relative to the true state of the teeth, due to inferior sharpness compared to camera images.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.729-730
• /
• 2008

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.05a
• /
• pp.303-306
• /
• 2012

According to the rapid development of cell phone and camera industry, all of electronic products obtain small-size, high-performance and variety. Therefore, PCB also obtains high-integration, multi-layers and high-specification rapidly. Among the digital cameras which are continuously evolved and developed, the market of mirror-less camera and hybrid digital camera is continuously increased because of the customer's request for small-size and weight lightening, except for DSLR camera. Therefore, the difficulty of PCB design is gradually increased and design L/T is longer according to the high-specifications, low-current and high-performance components. This thesis suggests the method to reduce L/T for PCB design applied to the reduction of digital camera's developing period and manufacturing period.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.6
• /
• pp.1204-1208
• /
• 2012

According to the rapid development of cell phone and camera industry, all of electronic products obtain small-size, high-performance and variety. Therefore, PCB also obtains high-integration, multi-layers and high-specification rapidly. Among the digital cameras which are continuously evolved and developed, the market of mirror-less camera and hybrid digital camera is continuously increased because of the customer's request for small-size and weight lightening, except for DSLR camera. Therefore, the difficulty of PCB design is gradually increased and design L/T is longer according to the high-specifications, low-current and high-performance components. This thesis suggests the method to reduce L/T for PCB design applied to the reduction of digital camera's developing period and manufacturing period.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2010.06a
• /
• pp.137-144
• /
• 2010

Ground digital image data obtained by using DSLR camera can be used to the ground photogrammetry and spatial modeling. Intensity of each pixel in digital video images is the most important parameter to generate digital image. Therefore, it is needed to estimate the parameters and spectral characteristics of digital cameras in order to take more definite intensity data. In this study, using the Sony DSC-F828 DSLR camera, seven digital images are obtained by the continuous shooting. (frame rate, 0.38 seconds). And then extract the value of the intensity from RGB band of each digital color photographs to confirm difference of intensity between frames. The purpose of this study is to confirm spectral characteristics and changes and to estimate correlation through the analysis of statistical in each pixel of R, G, B band.

• Korean Journal of Remote Sensing
• /
• v.32 no.1
• /
• pp.49-60
• /
• 2016

This paper presents a set of methods to evaluate the image quality of smartphone cameras as compared with that of a DSLR camera. In recent years, smartphone cameras have been used broadly for many purposes. As the performance of smartphone cameras has been enhanced considerably, they can be considered to be used for precise mapping instead of metric cameras. To evaluate the possibility, we tested the quality of one DSLR camera and 3 smartphone cameras. In the first step, we compare the amount of lens distortions inherent in each camera using camera calibration sheet images. Then, we acquired target sheet images, extracted reference lines from them and evaluated the geometric quality of smartphone cameras based on the amount of errors occurring in fitting a straight line to observed points. In addition, we present a method to evaluate the radiometric quality of the images taken by each camera based on planar fitting errors. Also, we propose a method to quantify the geometric quality of the selected camera using edge displacements observed in target sheet images. The experimental results show that the geometric and radiometric qualities of smartphone cameras are comparable to those of a DSLR camera except lens distortion parameters.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.28 no.1
• /
• pp.57-64
• /
• 2010

Measurements of deflection in load testing of structures are typically obtained with contact instrumentations such as LVDT (Linear-Variable Differential Transformer). LVDT only measure 1-dimensional deformation and in destructive testing is damage to instrumentation, thus prohibiting deflection when the beam is close to failure. Measurements of deflection using non-metric digital cameras are useful for load testing because there are very little cost or beam failure except for cheap targets and measurements in 3-dimensional deflection can obtained rapidly. In this research, deflection of concrete beam was measured using Nikon D80 DSLR camera, and the accuracy was evaluated with comparing the outputs to the LVDT measurements. The results show that the accuracy of terrestrial photogrammetric measurements are ${\pm}$0.5mm, ${\pm}$0.5mm, ${\pm}$0.6mm for each X, Y, Z directions, and the RMSE of comparison to LVDT is ${\pm}$0.57mm.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.12
• /
• pp.6082-6089
• /
• 2013

The supply of DSLR cameras has increased recently. Because of its widespread use, different types of DSLR camera video techniques have also been developed. Time-lapse is an effective filming technique that helps produce a fine-quality video clip by taking pictures of multiple camera shots during certain time intervals without recording the actual video clip, as the existing technique does. Machinery equipment (dolly), which controls the speed of movement and shutter, needs to be deleted. This paper introduces a method for a designing movement system that satisfies the design conditions. In addition, this paper proved the validity of the design by performing stress analysis on the static and dynamic conditions of the final design.

• Journal of the Korean earth science society
• /
• v.38 no.5
• /
• pp.323-332
• /
• 2017

The Digital Single Lens Reflex (DSLR) camera combined with a small aperture telescope is an efficient equipment for an astronomy-related lab exercise. This paper compares the different photometry softwares to provide insights on using the GUI-based photometry tool to the conventional command-line based photometry tool. The magnitude of the same point source measured within the aperture is consistent regardless of the software used although the background estimation, partial pixel treatment, and error estimation are slightly different. In a crowded field image where the aperture photometry is less reliable, the aperture photometry with varying aperture size is useful to see the qualitative trend for the magnitude. Due to the variation in ISO settings and the color dependence on the RGB Bayer system, an initial uncertainty of ~0.15mag is expected to be embedded in the magnitude derived from the DSLR images.

• KIPS Transactions on Computer and Communication Systems
• /
• v.12 no.9
• /
• pp.283-290
• /
• 2023

With the recent steady development of IoT technology, it is widely used in medical systems and smart TV watches. 66% of software development is developed through language C, which is vulnerable to memory attacks, and acts as a threat to IoT devices using language C. A stack-smashing overflow attack inserts a value larger than the user-defined buffer size, overwriting the area where the return address is stored, preventing the program from operating normally. IoT devices with low memory capacity are vulnerable to stack smashing overflow attacks. In addition, if the existing vaccine program is applied as it is, the IoT device will not operate normally. In order to defend against stack smashing overflow attacks on IoT devices, we used canaries among several detection methods to set conditions with random values, checksum, and DSLR (random storage locations), respectively. Two canaries were placed within the buffer, one in front of the return address, which is the end of the buffer, and the other was stored in a random location in-buffer. This makes it difficult for an attacker to guess the location of a canary stored in a fixed location by storing the canary in a random location because it is easy for an attacker to predict its location. After executing the detection program, after a stack smashing overflow attack occurs, if each condition is satisfied, the program is terminated. The set conditions were combined to create a number of eight cases and tested. Through this, it was found that it is more efficient to use a detection method using DSLR than a detection method using multiple conditions for IoT devices.