• Journal of KIISE:Information Networking
• /
• v.37 no.3
• /
• pp.243-248
• /
• 2010

This thesis proposes a power saving MAC protocol for LTE base station which utilizes different graded DRX/DTX(Discontinuous. Reception/Transmission) that specified by 3GPP(Third Generation Partnership Project). Considering QoS in UE, proposed MAC protocol controls adaptive DRX/DTX cycle. When Packet delay of UE is less than normal time, LTE base station economize power by increasing DRX/DTX. When Packet delay of UE is more than normal time, delay of UE is decreased by guaranteed QoS. It depends on the traffic which is sent by UE. The proposed method is more improve power saving performance than another method which is unchanged DRX/DTX by conditions. Especially when set DRX/DTX up in conditions, it will meet the requirements of UE. In this thesis, I propose an power saving MAC protocol in an environment where LTE base station are communicated with UE and prove improvement in performance through simulations.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.05a
• /
• pp.143-146
• /
• 2001

The evolution of dynamic recrystallization (DRX) was studied with torsion test for AISI 304 stainless steel in the temperature range of $900-1000^{\circ}C$ and strain rate range of 0.05-5/sec. The evolution of DRX was investigated with microstructural analysis and change of flow stress curve slope. The investigation of serrated grain boundaries using electron back scattered diffraction (EBSD) analysis indicated that the nucleated new DRX grain size was similar to the size of bulging part. Before the steady state, the dynamically recrystallizing grains do not remain a constant size and gradually grow to the size of fully DRX grain at steady state. The calculation of grain size was based on $X_{DRX}$ and the assumption, which the nucleated DRX grains are growing to the steady state, continuously. It was found that the calculated results agreed with the microstructure of the alloy.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2015.04a
• /
• pp.190-192
• /
• 2015

Discontinuous Reception 메커니즘은 LTE 시스템에서 고속 트래픽 성취에 뒤따른 이동 단말의 배터리 효율성의 중요도 상승에 따라 3GPP 표준으로 채택된 이용 단말의 비 연결적인 컨트롤 채널수신 확인 기법이다. 본 연구에서는 채널 상황 및 트래픽 특성에 효율적인 DRX 파라미터 설정의 중요성에 대해 확인하기 위해 Ns-3 시뮬레이터를 통해 DRX 활성/비활성 파라미터에 따른 성능을 확인하였으며 실험 결과에 통해 DRX 활성/비활성 파라미터의 비율에 따른 성능 변화를 확인하였다.

• ETRI Journal
• /
• v.38 no.4
• /
• pp.622-633
• /
• 2016

A discontinuous reception (DRX) operation is included in the Long Term Evolution (LTE) system to achieve power saving and prolonged battery life of the user equipment. An improvement in DRX power saving usually leads to a potential increase in the packet delay. An optimum DRX configuration depends on the current traffic, which is not easy to estimate accurately, particularly for non-real-time applications. In this paper, we propose a novel way to vary the DRX cycle length, avoiding a continuous estimation of the data traffic when only non-real-time applications are running with no active real-time applications. Because a small delay in non-real-time traffic does not essentially impact the user's experience adversely, we deliberately allow a limited amount of delay in our proposal to attain a significant improvement in power saving. Our proposal also improves the delay in service resumption after a long period of inactivity. We use a stochastic analysis assuming an M/G/1 queue to validate this improvement.

• Transactions of Materials Processing
• /
• v.9 no.1
• /
• pp.72-79
• /
• 2000

Dynamic recrystallization (DRX), which may occur during hot deformation, is important for the microsturctural evolution of 304 stainless steel. Especially, the current interest in modelling hot rolling demands quantitative relationships among the thermomechanical process variables, such as strain, temperature, strain rate, and etc. Thus, this paper individually presents the relationships for flow stress and volume fraction of DRX as a function of processing variables using torsion tests. The hot torsion tests of 304 stainless steel were performed at the temperature range of 900~110$0^{\circ}C$ and the strain rate range of 5x10-2~5s-1 to study the high temperature softening behavior. For the exact prediction of flow stress, the equation was divided into two regions, the work hardening (WH) and dynamic recovery (DRV) region and the DRX region. Especially, The flow stress of DRX region could be expressed by using the volume fraction of DRX (XDRX). Since XDRX was consisted of the critical strain($\varepsilon$c) for initiation of dynamic recrystallization (DRX) and the strain for maximum softening rate ($\varepsilon$*), that were related with the evolution of microstructure. The calculated results predicted the flow stress and the microstructure of the alloy at any deformation conditions well.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.9 no.1
• /
• pp.49-54
• /
• 2010

3GPP(Third Generation Partnership Project) LTE system that is the next step forward in cellular 3G services address the issues related to power saving at LTE base station. This is because that most of the energy in a typical telecommunication network is consumed by the wireless network's base station site. Power saving at LTE base station fall in with low-carbon green technology. This thesis proposes a power saving MAC protocol for LTE base station which utilizes different graded DRX/DTX(Discontinuous. Reception/Transmission). Considering traffic type in UE, proposed MAC protocol controls adaptive DRX/DTX cycle. The proposed method is more improve power saving performance than another method which is unchanged DRX/DTX by conditions. In this thesis, I propose an power saving MAC protocol in an environment where LTE base station are communicated with UE and prove improvement in performance through simulations.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.10a
• /
• pp.33-36
• /
• 2000

The dynamic recrystallization (DRX) of medium carbon steels (SCM 440 and POSMA45) was studied with torsion test in the temperature range of $900-1100^{\circ}C$ and the strain rate range of $5.0x10^{-2}\;-\;5.0x10^0/sec$. To establish the quantitative equations for DRX, the evolution of flow stress curve with strain was analyzed. The critical strain (${\varepsilon}_c$) and strain for maximum softening rate ( ${\varepsilon}^{*}$) could be confirmed by the analysis of work hardening rate ($d{\sigma}/d{\varepsilon}\;=\; \theta$). The volume fraction of dynamic recrystallization ($X_{DRX}$) as a function of processing variables, such as strain rate ( $\dot{\varepsilon}$ ), temperature (T), and strain ( $\varepsilon$ ) were established using the ${\varepsilon}_c$ and ${\varepsilon}^{*}$. For the exact prediction, the ${\varepsilon}_c$, ${\varepsilon}^{*}$ and Avrami' exponent (m') were quantitatively expressed by dimensionless parameter, Z/A respectively. The transformation-effective strain-temperature curve for DRX could be composed. It was found that the calculated results were agreed with the experimental data for the steels at any deformation conditions.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.293-296
• /
• 2001

The dynamic softening mechanisms of AISI 316, AISI 304 and AISI 430 stainless steels were studied with torsion test in the temperature range of $900 - 1200^{\circ}C$ and the strain rate range of $5.0x10^{-2}-5.0x10^0/sec$. The austenitic stainless steels, such as AISI 316 and AISI 304 were softened by dynamic recrystallization (DRX) during hot deformation. Also, the evolutions of flow stress and microstructure of AISI 430 ferritic stainless steel show the characteristics of continuous dynamic recrystallization (CDRX). To establish the quantitative equations for DRX of AISI 316 stainless steel, the evolution of flow stress curve with strain was analyzed. The critical strain (${\varepsilon}_c$) and strain for maximum softening rate (${\varepsilon}^{*}$) could be confirmed by the analysis of work hardening rate ($d{\sigma}/d{\varepsilon}={\theta}$). The volume fraction of dynamic recrystallization ($X_{DRX}$) as a function of processing variables, such as strain rate ( $\varepsilon$ ), temperature (T), and strain ( $\varepsilon$ ) were established using the ${\epsilon}_c$ and ${\varepsilon}^{*}$. For the exact prediction the ${\varepsilon}_c,\;{\varepsilon}^{*}$ and Avrami' exponent (m') were quantitatively expressed by dimensionless parameter, Z/A, respectively. It was found that the calculated results were agreed with the experimental data for the steels at my deformation conditions. Also, we can reasonably conclude that the DRX, CDRX and grain refinement of stainless steels can be achieved by large strain deformation at high Z parameter condition.

• Transactions of Materials Processing
• /
• v.31 no.6
• /
• pp.344-350
• /
• 2022

Extruded Mg-Bi binary alloys are known to have an undesirable bimodal grain structure containing a large amount of coarse unrecrystallized grains. Accordingly, to improve the microstructural homogeneity of extruded Mg-Bi alloys, it is necessary to promote the dynamic recrystallization (DRX) behavior during hot extrusion. An effective way to promote DRX is an increase in nucleation sites for DRX through a pre-deformation process before extrusion, such as cold pre-forging and hot pre-compression. However, the application of these pre-deformation processes increases the cost of final extruded Mg products because of an increase in energy consumption and decrease in productivity. Therefore, a low-cost new continuous process with high productivity is required to improve the microstructural homogeneity and mechanical properties of extruded Mg alloys without a drastic increase in the entire process cost. This study proposes a new extrusion method using an extrusion billet with a truncated cone shape (i.e., tapered billet) instead of a conventional extrusion billet with a cylindrical shape. When the hot extrusion of a Mg-5Bi alloy is conducted using the tapered billet, the DRX behavior during extrusion is considerably promoted. The DRX fraction and average grain size of the extruded alloy significantly increase and decrease from 65% to 91% and from 225 ㎛ to 49 ㎛, respectively. Consequently, the extruded Mg-5Bi alloy fabricated using the tapered billet has a finer homogeneous grain structure and higher tensile elongation than the extruded counterpart fabricated using the cylindrical billet.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.2
• /
• pp.285-289
• /
• 2020

The configuration of hierarchical wireless networks is provided to support diverse network environments. In the base station, two system state can be basically considered for the operation management so that the state transition may be occurred between active and sleep modes. Hence, to reduce energy consumption the system operation management of the low power should be considered to the base station system. In this paper we consider the analytical model of Discontinuous Reception (DRX) to investigate the system management. We provide the analysis scheme of base station system by the DRX model, and the low power factor would be investigated for the energy consumption. We also use the finite-state Markov system model that in a system state period the wireless resource request and the operation of service call arrival interval is considered to numerically analyze the performance of energy saving operations of base station.