• Proceedings of the KIPE Conference
• /
• 2018.07a
• /
• pp.186-188
• /
• 2018

In this paper, a single-phase multifunctional onboard battery charger with small DC-link capacitors is proposed, where the low-voltage battery charger is utilized as an active power filter to mitigate the inherent second-order ripple power when the high-voltage (HV) battery is charged from the grid. In this scheme, the large DC-link electrolytic capacitors of the HV battery charger can be eliminated without additional switches, leading to the reduction of cost and volume of the onboard battery charger. The validity of the proposed topology has been verified by the simulation results.

• Journal of Electrical Engineering and Technology
• /
• v.5 no.2
• /
• pp.290-298
• /
• 2010

This paper proposes an adaptive carrier-based pulse width modulation (PWM) method for a four-switch three-phase (4S3P) inverter under dc-link voltage ripple conditions. The proposed method guarantees balanced output currents despite of the existence of the voltage oscillations across two dc-link capacitors. And also, this new approach achieves a linear over-modulation with calculation time reduction. Simulation and experimental results are given to validate the feasibility of the proposed method.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.487-490
• /
• 2001

Power Quality and Reliability are becoming important issues for critical and sensitive loads. This paper describes the Line Interactive UPS with the function of Voltage Compensator that is 'Line interactive Dynamic Voltage Restorer(LIDVR). The main purpose of a LIDVR is to compensate for voltage sag(dip), outage and overvoltage. The overall system consists of three controller 1) current controller with prediction 2) voltage controller and 3) proposed variable DC LINK controller. The variable DC LINK control technique using the LIDVR protects DC LINK from overflowing the input current. The simulation results are depicted in this paper to show the effect of this proposed system.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.594-599
• /
• 2001

A study of single-stage PFC electronic ballast with constant do-link voltage is presented in this paper. The proposed ballast is combined by two interleaved boost cells and a conventional half bridge dc/ac inverter, By exploiting the interleaving technique, the Input ripple current of the electronic ballast is reduced. Theoretical analysis and experimental results for two 45(W) fluorescent lamps are presented.

• Journal of Power Electronics
• /
• v.11 no.3
• /
• pp.285-293
• /
• 2011

This paper proposes two SRM driving systems using a variable dc-link voltage controlled by a single-phase inverter. Two SRM converter topologies of a half bridge type and a full bridge type are proposed according to the power circuits of an inverter. The phase current can be controlled by means of a PWM controller at the inverter, and the turn-on/off angle at the phase switches can be controlled by a position sensor at the converter in the drive system. The inverter acts as a peak-current limiter if the transient current exceeds its maximum value. SRMs using the proposed topologies maintain high efficiency due to energy regeneration after the turn-off of power switches. The operational modes of the proposed topologies are verified by simulation and experimental results.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.205-206
• /
• 2015

본 논문에서는 단일 전류 센서를 가진 IPMSM 구동 시스템의 고주파 신호 주입 센서리스 제어를 제안한다. 단일 전류 센서 시스템에서 3상 전류를 재구축하기 위해 DC link 전류를 검출한다. DC link 전류를 이용하여 3상 전류를 재구축하는 경우의 문제점은 1개 또는 2개의 유효벡터가 DC link 전류를 검출하는데 필요한 최소 시간보다 짧게 인가될 때 발생한다. 센서리스 제어시 이러한 경우가 발생하면, 재구축된 전류의 왜곡에 의해 제어 성능이 저하된다. 본 논문은 전압 벡터가 작은 경우, 전류 예측을 통하여 신뢰할 만한 3상 전류를 재구축하여 전류의 왜곡을 줄임으로써 센서리스 제어 성능을 향상시켰다. 시뮬레이션을 통하여 제안한 기법의 타당성을 검증하였다.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1080-1082
• /
• 2005

This paper presents the system design of permanent magnet linear synchronous machine with double-side PM mover and slotless iron-cored stator in the required speed and thrust. in this paper, the design of manufacturing motor is optimized by characteristics of motor parameters with the variation of PM size and coil turns. And, the permissible operating range of manufactured motor by determination of base speed and base thrust according to switching scheme of DC link voltage are offered. Finally, the results of analytical solutions are verificated by finite element analysis and experiment.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1364-1367
• /
• 2005

In this paper, a novel prototype topology of soft switching PWM controlled high frequency AC power conversion circuit without DC voltage smoothing chemical capacitor filter link from the voltage grid of utility frequency AC power supply source with 60Hz-100V or 60Hz-200V is proposed and introduced for innovative consumer induction heating(IH) boiler applications as hot water producer, steamer and super heated vapor steamer.

• Proceedings of the KIPE Conference
• /
• 2015.11a
• /
• pp.46-47
• /
• 2015

본 논문은 태양광 발전 시스템의 차동 전력 조절 방식 중 Feed-Foward 방식을 적용한 다중 출력 플라이백 컨버터를 이용하여 DC_Link 다중 출력 전압을 균등화 하는 회로에 대한 내용이다. DC_Link가 여러 단으로 되어 있을 경우, 전압을 일정하게 맞추어 줄 필요가 있는데, 이를 차동 전력 조절기(Differential Power Processing converter)를 통해서 DC_Link 출력 전압을 균등화 할 수 있다. 스트링 컨버터인 부스트 컨버터의 스트링 전류를 제어 하여 부스트 컨버터의 전력과 DPP역할을 하는 다중 출력 플라이백 컨버터로 전달되는 전력을 조정가능하다. 이를 통하여 전압 균등화가 이루어지게 할 수 있고, 각 DPP 컨버터는 PV 전압 제어를 하여 MPPT 동작을 하게 된다. PSIM 시뮬레이션과 150W급 하드웨어 프로토타입을 제작해 실험을 통하여 검증 하였다.

• Proceedings of the KIPE Conference
• /
• 2010.11a
• /
• pp.70-71
• /
• 2010

태양광 전력조절기에서 임의의 위상을 갖는 모듈통합형 스트링 구조는 출력 커패시터의 리플 크기가 모듈 수만큼 생기게 되어 일정 리플을 위한 커패시턴스를 키워야 하고 이는 크기 및 가격, 효율 면의 입장에서 불리한 요소가 될 수 있다. 본 논문에서는 모듈간의 위상 동기화를 통한 인터리빙 기법을 적용하여 DC-Link 전압의 리플이 저감됨을 분석 및 시뮬레이션을 통해 확인하고 이를 하드웨어 Prototype 제작하여 타당성을 검증하였다.