• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.4
• /
• pp.307-312
• /
• 2006

This paper proposes the SRM drive system, which accurately estimates the phase currents from the DC-link current to drive SRM instead of detecting the three-phase currents. In addition, the detecting circuit of DC-link current is also proposed to increase the resolution and decrease the off-set influence. Comparing with the general drive system based on the phase current, it is verified through the experiments that the proposed SRM drive system based on the DC-link current has the good performance in steady-state response of the speed control. Using the DC-link current, all of the 3-phase currents can be easily estimated for driving the SRM.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.8
• /
• pp.116-121
• /
• 2005

To realize the tap coefficient of a finite impulse response(FIR) filter or the twiddle factor of a fast Fourier transform(FFT) using a current-mode analog circuit, a high accurate current-attenuator circuit is needed This paper introduces an accuracy enhancement technique in the current-mode signal processing. First of all, the DC of set-current error in a conventional current-attenuator using a gate-ratioed orient mirror circuit is analyzed and then, the current-attenuator circuit with a negligibly small DC offset-current error is introduced. The circuit consists of N-output current mirrors connected in parallel with me another. The output current of the circuit is attenuated to 1/N of the input current. On the basis of the Kirchhoff current law, the current scale ratio is determined simply by the number of the current mirrors in the N-current mirrors connected in parallel. In the proposed current-attenuator circuit the scale accuracy is limited by the ac gain error of the current mirror. Considering that a current mirror has a negligibly small ac gain error, the attainable maximum scale accuracy is theoretically -80[dB] to the input current.

• Journal of Power Electronics
• /
• v.15 no.4
• /
• pp.1006-1017
• /
• 2015

This paper presents a finite control set model predictive control (FCS-MPC) strategy for the AC/DC matrix converter used in grid-connected battery energy storage system (BESS). First, to control the grid current properly, the DC current is also included in the cost function because of input and output direct coupling. The DC current reference is generated based on the dynamic relationship of the two currents, so the grid current gains improved transient state performance. Furthermore, the steady state error is reduced by adding a closed-loop. Second, a Luenberger observer is adopted to detect the AC input voltage instead of sensors, so the cost is reduced and the reliability can be enhanced. Third, a switching state pre-selection method that only needs to evaluate half of the active switching states is presented, with the advantages of shorter calculation time, no high dv/dt at the DC terminal, and less switching loss. The robustness under grid voltage distortion and parameter sensibility are discussed as well. Simulation and experimental results confirm the good performance of the proposed scheme for battery charging and discharging control.

• Journal of Digital Convergence
• /
• v.18 no.11
• /
• pp.241-246
• /
• 2020

In this paper, we propose a neural network model to converge the marine electric propulsion system and deep learning algorithm to predict the DC/DC converter output current in the electric propulsion regeneration system and to predict the battery charge during regeneration. In order to experiment with the proposed neural network, the input voltage and current of the PCM were measured and the data set was secured on the prototype PCM board. In addition, in order to improve the learning results in the insufficient data set, the scale of the data set was increased through data fitting and its learning was executed further. After learning, the difference between the data prediction result of the neural network model and the actual measurement data was compared. The proposed neural network model effectively showed the prediction of battery charge according to changes in input voltage and current. In addition, by predicting the characteristic change of the analog circuit constituting the DC/DC converter through a neural network, it is determined that the characteristics of the analog circuit should be considered when designing the regeneration system.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.1
• /
• pp.42-48
• /
• 2020

As global warming accelerates, eco-friendly electric cars are being developed to reduce carbon dioxide emissions, and power conversion inverters are used to drive motors. Among inverter components, DC-link capacitor is heated by high current usage, which causes problems such as performance and life-saving of inverter. Although metal cases with good thermal performance have been used to solve this problem, it is difficult to apply them in practice due to insulation problems with other parts. In this paper, the Heat-Generation influence factor of DC-link capacitor is analyzed. Variables on heat-generation are set at 3 levels for film width, inductance, and film thickness. Box-Behnken to 13 tests using the design and minimal deviations, e.g. through the experiment three times by each level. The surface of the film k type by attaching the sensor current is measured temperature. Capacitance was set to a minimum level of 200 ㎌ and had a frequency of 16 kHz with Worst case, ambient temperature of 85℃ and a ripple current of 50 Ams was applied. The temperature at the measurement point was collected in the data logger after sampling at 1 minute intervals for 2 hours after saturation with the ambient temperature. This experiment confirmed that setup factors are correlated with heat-generation.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.575-577
• /
• 2005

This paper proposes the SRM drive system based on DC-link current, from which the phase currents can be estimated in accuracy and also they can be used in driving SRM instead of the three-phase currents. In additional, the detecting circuit for DC-link current is also proposed for increasing the resolution and decreasing the off-set. Comparing to the general drive system based on the phase current, it is verified through the experiment that the proposed SRM drive system has the good performance in steady-state responses of the speed control. Using the DC-link current, all of the 3-phase currents can be easily estimated in driving the SRM.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2004.04a
• /
• pp.153-156
• /
• 2004

This Paper deals with speed control of DC servo motor using a Fuzzy-Sliding observer. Speed sensor detect a speed of rotor continuously. But It have a limit as a driving speed to detect speed precisely. So it is problem to improve the performance of the driving system To solve the problem, it is studied to detect a speed of DC motor without sensor In particular, study on the method to estimate the speed using the observer is performed a lot. In this parer, the gain of the observer is properly set up using the fuzzy control and sliding observer that have a superior transient characteristic and is easy to implement compared the exist ing method is designed. It estimate the derivative of the armature current directly using the armature current measured in the DC motor. It estimate the speed of the rotor using the differentiation. It is Proposed speed sensor less control method using the estimated speed. Optimal gain of Luenberger observer is set up using the fuzzy control and adapted speed control of DC servo motor. It is proved excellence and feasibility of the presented observer from the comparison tested a case with a speed sensor and a case without a speed sensor which used a highly efficient drive and 200W DC servo motor start ing system.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.57 no.3
• /
• pp.244-249
• /
• 2008

This paper deals with speed control of DC servo motor using a Fuzzy tuning observer. Speed sensor detect a speed of rotor continuously. But it have a limit as a driving speed to detect speed precisely. So it is problem to improve the performance of the driving system. To solve the problem, it is studied to detect a speed of DC motor without sensor. In particular, study on the method to estimate the speed using the observer is performed a lot. In this parer, the gain of the observer is properly set up using the fuzzy observer. The fuzzy observer has a superior transient characteristic and is easy to implement compared the existing method is designed. It estimate the derivative of the armature current directly using the armature current measured in the DC motor. It estimate the speed of the rotor using the differentiation. It is proposed speed sensorless control method using the estimated speed. Optimal gain of Luenberger observer is set up using the fuzzy observer and adapted speed control of DC servo motor low speed operation. It is proved excellence and feasibility of the presented observer from the comparison tested a case with a speed sensor and a case without a speed sensor which used a highly efficient drive and 200W DC servo motor starting system.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.8
• /
• pp.1360-1365
• /
• 2010

In this paper, we propose a distance relaying algorithm using a Discrete Fourier Transform (DFT)-based modified phasor estimation method to eliminate the adverse influence of exponentially decaying DC offsets. Most distance relays are based on estimating phasors of the voltage and current signals. A DFT is generally used to calculate the phasor of the fundamental frequency component in digital protective relays. However, the output of the DFT contains an error due to exponentially decaying DC offsets. For this reason, distance relays have a tendency to over-reach or under-reach in the presence of DC offset components in a fault current. Therefore, the decaying DC components should be taken into consideration when calculating the phasor of the fundamental frequency component of a relaying signal. The error due to DC offsets in a DFT is calculated and eliminated using the outputs of an even-sample-set DFT and an odd-sample-set DFT, so that the phasor of the fundamental component can be accurately estimated. The performance of the proposed algorithm is evaluated for a-phase to ground faults on a 345 kV, 50 km, simple overhead transmission line. The Electromagnetic Transient Program (EMTP) is used to generate fault signals. The evaluation results indicate that adopting the proposed algorithm in distance relays can effectively suppress the adverse influence of DC offsets.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.713-717
• /
• 2004

This is a thesis that a quarter-brick size of 100W class open-frame type on board power module comprising telecommunication application is reported. The input voltage is established between 36 and 75 in range in order for power module to be utilized for the telecommunication application, and output were set at 3.3V and 30A. A number of parts used for transformer, inductor, and hit sink are composed of PCB in order for DC-DC converter to be lowered below 8 mm. A constant current control circuit was annexed to the system as well as basic protection prototypes such as over-voltage, over-current, and over-temperature were well considered to enhance more credibility, and were tested. As a result, high circuit performance and credibility turned out to be significant.