• 한국재료학회지
• /
• 제19권1호
• /
• pp.24-27
• /
• 2009

Indium Gallium Zinc Oxide (IGZO) thin films were deposited onto 300 nm-thick oxidized Si substrates and glass substrates by direct current (DC) magnetron sputtering of IGZO targets at room temperature. FESEM and XRD analyses indicate that non-annealed and annealed IGZO thin films exhibit an amorphous structure. To investigate the effect of an annealing treatment, the films were thermally treated at $300^{\circ}C$ for 1hr in air. The IGZO TFTs structure was a bottom-gate type in which electrodes were deposited by the DC magnetron sputtering of Ti and Au targets at room temperature. The non-annealed and annealed IGZO TFTs exhibit an $I_{on}/I_{off}$ ratio of more than $10^5$. The saturation mobility and threshold voltage of nonannealed IGZO TFTs was $4.92{\times}10^{-1}cm^2/V{\cdot}s$ and 1.46V, respectively, whereas these values for the annealed TFTs were $1.49{\times}10^{-1}cm^2/V{\cdot}$ and 15.43V, respectively. It is believed that an increase in the surface roughness after an annealing treatment degrades the quality of the device. The transmittances of the IGZO thin films were approximately 80%. These results demonstrate that IGZO thin films are suitable for use as transparent thin film transistors (TTFTs).

• Corrosion Science and Technology
• /
• 제20권3호
• /
• pp.112-117
• /
• 2021

Inductively coupled plasma magnetron sputtering (ICPMS) has the advantage of being able to dramatically improve coating properties by increasing the plasma ionization rate and the ion bombardment effect during deposition. Thus, this paper presents the comparative results of CrN films deposited by direct current magnetron sputtering (dcMS) and ICPMS systems. The structure, microstructure, and mechanical and corrosive properties of the CrN coatings were investigated by X-ray diffractometry, scanning electron microscopy, nanoindentation, and corrosion-resistance measurements. The as-deposited CrN films by ICPMS grew preferentially on a 200 plane compared to dcMS on a 111 plane. As a result, the films deposited by ICPMS had a very compact microstructure with high hardness. The nanoindentation hardness reached 19.8 GPa, and 13.5 GPa by dcMS. The corrosion current density of CrN film prepared by ICPMS was about 9.8 × 10^-6 mA/cm², which was 1/470 of 4.6 × 10^-3 mA/cm², the corrosion current density of CrN film prepared by dcMS.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2017년도 춘계학술대회 논문집
• /
• pp.103.2-103.2
• /
• 2017

Nanocrystalline HfN coatings were prepared by reactively sputtering Hf metal target with N2 gas using a magnetron sputtering system operated in DC and ABPP (asymmetric bipolar pulsed plasma) condition with various duties and frequencies. The effects of duty and frequency, ranging from 75 to 100 % and 5 to 50 kHz, on the coating microstructure, crystallographic and mechanical properties were systematically investigated with FE-SEM, AFM, XRD and nanoindentation. The results show that pulsed plasma has a significant influence on coating microstructure and mechanical properties of HfN coatings. Coating microstructure evolves from the columnar structure to a highly dense one as duty decreases. Average grain size and nano hardness of HfN coatings were also investigated with various pulsed conditions.

• 한국정보통신학회논문지
• /
• 제10권3호
• /
• pp.473-478
• /
• 2006

DC 마그네트론 스퍼터링 방법으로 ITO 박막을 형성하였다. 박막 형성 시 스퍼터 전압을 변화시켜 음이온에 의한 손상을 최소화하였으며, 또한 기판온도와 산소유입량을 변화시켜 비저항 $1.6\times10^{-4}{\Omega}cm$, 광투과도 90% 이상의 값을 갖는 양질의 박막을 형성 할 수 있었다. 박막 형성 시 $O_2$ 가스의 유량이 4sccm 이상으로 산소공급이 과다할 경우는 ITO 박막의 비저항이 증가하고, 광 투과도가 포화됨을 알 수 있었다.

• 한국표면공학회지
• /
• 제45권3호
• /
• pp.117-122
• /
• 2012

ZTO/GZO double layered films were prepared on unheated non-alkali glass substrates. ZTO films were deposited by RF/DC hybrid magnetron co-sputtering using ZnO (RF) target and $SnO_2$ (DC) targets, and then GZO films were deposited by DC magnetron sputtering using an GZO ($Ga_2O_3$:5.57 wt%) target. These films were post-annealed at temperature of 200, $300^{\circ}C$ in air and vacuum ambient for 30 min. In the case of post-annealing in air, ZTO/GZO double layer showed relatively low resistivity change, compared to GZO single layer. Furthermore, ZTO/GZO double layer revealed low WVTR, compared to GZO single layer. Therefore, it can be confirmed that ZTO film doing a role with barrier for water or oxygen diffusion.

• 한국세라믹학회지
• /
• 제33권7호
• /
• pp.735-742
• /
• 1996

Antimony-doped Tin oxide (ATO) thin films were deposited on soda-lime glass substrates by DC magnetron sputtering technique. Effects of DC power film thickness and post heat-treatment on electrical conductivity of ATO film were investigated. Other properties of ATO film such as optical anti-chemical and wear properties were also reported in this work. The obtained ATO films showed electrical resistivities ranging from 5$\times$10-3 $\Omega$cm to 3$\times$10-3 $\Omega$cm with the average optical transparency above 80% in visible wavelength range and excel-lent anti-chemical properties where the electrical resistivity was not changed even after soaking the films in 1M HCl or 1M NaOH solution for 10 days. These properties were found to be related to the crystallinity of ATO film and the films having higher crystallinity showed better properties.

• 대한금속재료학회지
• /
• 제47권6호
• /
• pp.378-382
• /
• 2009

We investigated the effects of deposition conditions on the fabrication of $Fe_{3}O_{4}$ thin films using a reactive DC magnetron sputtering at room temperature. The structural, electrical, and magnetic properties of Fe oxide films dependence on the film thickness, oxygen flow rate, and the substrate crystallinity were also studied. We have successfully fabricated $Fe_{3}O_{4}$ film with thickness of about 10 nm under optimal reactive sputtering conditions. The saturation magnetization, resistivity, and Verwey transition of the $Fe_{3}O_{4}$ film were298 emu/cc, $4.0{\times}10^{-2}{\Omega}cm$, and 125 K, respectively.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권3호
• /
• pp.149-154
• /
• 2000

Bi-layer Mo films were deposited on soda-lime glass substrates using DC magnetron supttering. Increasing gas pressure, the resistivity varied from $1\times10^{-5}\; to\; 8.3\times10^{-3}\; \Omega.cm$. Furthermore, stress direction yielded compressive-to-tensile transition stress curves. The micro-structure of the compressively-stressed film which had poor adhesion consists of tightly packed columns, but of the tensile-stressed films had less dense structure. Under all gas pressure conditions, Mo films exhibited distinctly increasing optical reflection with decreasing gas pressure. The expansion of (110) peak width with the gas pressure meant the worse crystalline growth. The impurity levels in the Mo film exhibited highly concentrated Na, Se and O elements due to less dense micro-structure. The degree of Na diffusion depends on the type of the glass substrate used and the nature of the Mo film.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2007년도 하계종합학술대회 논문집
• /
• pp.441-442
• /
• 2007

We deposited nickel oxide(NiO) thin films on silicon(Si) substrates at Room temperature and $500^{\circ}C$ using a nickel target by reactive DC and RF sputtering. In addition, we anneal to NiO thin films deposited at room temperature. Using spectroscopic eillipsometry, we obtained optical characteristics of every films. We discussed relations of the optical and structural properties of NiO thin films with the oxygen flow rate, substrate temperature and annealing temperatures. Refraction was decreased and defect was increased when NiO thin films was annealed. We also analyzed the electrical characteristics of NiO films which deposited DC and RF sputtering method.

• 한국전기전자재료학회논문지
• /
• 제13권5호
• /
• pp.376-382
• /
• 2000

We successfully fabricated OLED(Organic Light Emitting Diodes) with Al cathodes electrode deposited by the DC magnetron sputtering. The effects of a controlled Al cathode layer of an Indium Tin Oxide (ITO)/blended single polymer layer (PVK Bu:PBD:dye)/Al light emitting diodes are described. The PVK (Poly(N-vinylcarbazole)) and Bu-PBD (2-(4-biphenyl-phenyl)-1,3,4-oxadiazole) are used hole transport polymer and electron transport molecule respectively. We found that both current injection and electroluminescence output are significantly different with a variable DC sputtering power. The difference is believed to be due to the influence near the blended polymer layer/cathode interface that results from the DC power and H$\sub$2//O in a chamber. And DC sputtering deposition is an effective way to fabricate Al electrodes with pronounced orientational characteristics without damage occurring to metal-organic interface during the sputtering deposition.