• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.05a
• /
• pp.291-294
• /
• 2007

This paper preserts the characteristics of leakage currents flowing through 18 kV zinc oxide (ZnO) surge arrester under the mixed DC and AC voltages. The I-V curves of ZnO surge arrester were measured as a function of the voltage ratio K The I-V curves under the mixed DC and AC voltages lay between the pure DC and AC characteristics, and the cross-over phenomenon in I-V curves was observed at the low current region As a result, the increase of DC component to mixed voltages causes the increase of resistive component of total leakage current th ZnO surge arrester.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.05a
• /
• pp.295-299
• /
• 2007

Biped robot requires that an energy source and a control part should be installed on the body to realize active system. So, we choose the DC motor having high torque in compact size in this study. In the DC motor serve system, we choose power amplifier with analog configuration, developed the module combined the controller and the driver. We applied this module to robot actuator and studied the response characteristics in an action and a return. Main controller with serve system, loading PIC micro controller, can be load on the robot with light weight.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.213-215
• /
• 2003

This paper deals with the characteristics of a prototype solenoid for basic design of DC reactor type superconducting fault current limiter (SFCL). The prototype high-Tc Super-conducting (HTS) solenoid was manufactured with 4 stacked Bi-2223 tape. The critical currents were measured with respect to the number of stacks. In order to test the safety of HTS solenoid in quenched state, the transport tests of AC over-current were performed. These experimental results could be applied to the basic design of HTS DC reactor for SFCL effectively.

• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.530-533
• /
• 1987

In high-frequency switched mode converters, Series Resonant Converter (SRC) is investigated using state-plane method. Phase plane trajectories of the SRC permit a direct closed form solution of the steady state operation and can make problems easy to solve. This paper describes steady state responses and characteristics of the SRC with respect to various circuit factors. The magnitute of steady state response and the average current through load are clearly related to how such the switching frequency differs from the resonant frequency. The results of the steady state analysis can be used to estimate the device and component stress on the power circuit.

• Proceedings of the KSR Conference
• /
• 1999.05a
• /
• pp.328-335
• /
• 1999

Three phase full bridge rectifier has been used to obtain dc voltage from three phase ac voltage source. The rectifier system has drawbacks that power factor is low and power flow is unidirectional. Therefore, when dc voltage increases due to regeneration of power the dynamic resister for dissipation of regeneration power must be installed. But three phase PWM converter can be controlled to operate with unity power factor and bidirectional power flow. Therefore when the PWM converter is used as do supply system, the dissipating resistor is not necessary. On this thesis, in order to design a controller having good performance, the hee phase PWM converter is completely modeled by using circuit DQ-transformation and thus a general and simple instructive equivalent circuit is obtained; the inductor set becomes a second order gyrator-coupled system and three phase inverter becomes a transformer as well. Under given phase angle(${\alpha}$) and modulation index(MI) of the three phase inverter, the dc and ac characteristics are obtained by analysis of the transformed equivalent circuit The validity of the equivalent circuit is confirmed through PSPICE simulation. And based on the dc and ac characteristics a controller with unity power factor is proposed.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.200-204
• /
• 1998

In this paper, a mathematical model of Brushless DC machine fed by pwm inverter is developed. Dynamic and steady state characteristics of Brushless DC motor is simulated and analyzed: electromagnetic torque, speed, phase voltage, and current. In mathematical modeling, the shaft transformation referencing rotor frame from to "a,b,c" three phase frame to "d,g" two phase frame is described.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.385-387
• /
• 1999

Brushless DC Motors are widely used because of their high power ratio and easy control. But the brushless DC Motors need rotor Position- and speed- sensor such as encoder, resolver and hall sensor. The position sensor has present several disadvantages from the standpoint of drive cost, machine size and reliability. Hall sensors are used generally because of low cost but their operating temperature is limited up to $75^{\circ}C$ because of sensitivity of temperature. Now a day many research projects are on the development of sensorless brushless DC motors to correct these disadvantages. In this paper, characteristics such as starting, change of speed and load of a sensorless brushless DC motor are investigated.

• Proceedings of the KIEE Conference
• /
• 2005.10a
• /
• pp.75-78
• /
• 2005

Fuel cell is remarkable for one of the clean energy recently. But in the fuel cell case, it has characteristics with low voltage and high current. Therefore, for using domestic power, it should be changed to the power source with commercial voltage and frequency. In this paper fuel cell simulator having electrical characteristics is designed and constructed instead of fuel cell stack. Voltage generated from fuel cell is from 39V to 72V dc and should be boosted to 400V dc for home appliances. A stand alone system including the inverter and DC/DC converter for the fuel cell is then proposed. Simulation result is used to support the analysis.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.5
• /
• pp.804-812
• /
• 1987

1\ulcorner gate MESFETs are fabricated on MOCVD and VPE grown GaAs wafers using photolithography, chemical wet etching and lift-off techniques. DC characteristics such as Vt, Gm, Rs, etc. are studied and active channel parameters of MESFET(a, n, Leff, \ulcorner)are analyzed for 1-4 \ulcorner gate FETs and 100\ulcorner FAT FET. The correlation between DC data and active channel parameters are experimentally analyzed. The measured transconductance and low-field mobility in the active channel for the 1\ulcorner gate MESFET made on MOCVD wafer are 67mS/mm and 2980cm\ulcornerVs respectively.

• Proceedings of the IEEK Conference
• /
• 2007.07a
• /
• pp.441-442
• /
• 2007

We deposited nickel oxide(NiO) thin films on silicon(Si) substrates at Room temperature and $500^{\circ}C$ using a nickel target by reactive DC and RF sputtering. In addition, we anneal to NiO thin films deposited at room temperature. Using spectroscopic eillipsometry, we obtained optical characteristics of every films. We discussed relations of the optical and structural properties of NiO thin films with the oxygen flow rate, substrate temperature and annealing temperatures. Refraction was decreased and defect was increased when NiO thin films was annealed. We also analyzed the electrical characteristics of NiO films which deposited DC and RF sputtering method.