• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.460-465
• /
• 1998

Due to high power ratings and low conduction loss, the IGBT has become more attractive in switching power supplies. However, its turn-on and turn-off characteristics cause severe switching loss and switching frequency limitation. This paper proposes 2.4kW, 48V, high efficiency half-bridge DC-DC converter using paralleled IGBT-MOSFET switch concept, where each of IGBT and MOSFET plays its part during on-periods and switching instants. The switching loss is analyzed by using the linearized model and the opteration of the converter are investigated by simulation results.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.289-291
• /
• 2005

In this paper results of the experiment which used LLC resonant half bridge DC-DC converter to a portable electrical equipment. LLC resonance Half Bridge DC-DC converter which was used in this experiment improved an efficiency because it reduced switching, conduction losses and with synchronous rectifier. As a result of the experiment, this proposed converter could verified an increase of 2% to the efficiency more than diode rectifier.

• 전기의세계
• /
• v.28 no.1
• /
• pp.67-72
• /
• 1979

The most difficult problem encountered in the DC Chopper is the improvement in it's output waveforms and the commutation failure. Thus, this paper deals with the Load Insensitive DC Chopper that produces a quasi-pure square wave over the entire load range, and doesn't fail the commutation. The authors compared voltage and current waveforms from the laboratory model with those from the computer simulation, and it's characteristics is discussed.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1092-1093
• /
• 2007

본 논문은 DC-Link 전압가변에 의한 전구형 무전극 램프의 조광제어 특성을 분석한 결과 전력이 $20%{\sim}100%$ 제어 가능함을 실험적으로 밝혔다. DC-Link 전압가변은 벅 컨버터의 듀티를 제어하였으며, 전구형 무전극 램프의 조광제어 특성을 분석하였다.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.5
• /
• pp.923-930
• /
• 2020

In modern society, various DC power supplies are required to operate the system circuits of various electric devices. A stable DC supply is essential for the normal operation of the circuit and the importance of the converter for this is very high. This study proposed a PWM DC-DC converter circuit that applied a 3-pole 2-zero voltage controller to a KY converter, a step-up DC-DC converter, to maintain a stable supply of output voltage regardless of load fluctuations. In order to prove the normal operation characteristics of the proposed converter circuit, a PSIM simulation and a circuit operation experiment on the PCB board were performed in comparison with the conventional converter circuit.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.2
• /
• pp.54-63
• /
• 2007

Recently, a fuel cell with low voltage and high current output characteristics is remarkable for new generation system. It needs both a DC-DC step-up converter and DC-AC inverter to be used in fuel cell generation system. Therefor, this paper, consists of an isolated DC-DC converter to boost the fuel cell voltage $380[V_{DC}]$ and a PWM inverter with LC filter to convent the DC voltage to single-phase $220[V_{AC}]$. Expressly, a tapped inductor filter with freewheeling diode is newly implemented in the output filter of the proposed high frequency isolated ZVZCS PWM DC-DC converter to suppress circulating current under the wide output voltage regulation range, thus to eliminate the switching and transformer turn-on/off over-short voltage or transient phenomena. Besides the efficiency of 93-97[%]is obtained over the wide output voltage regulation ranges and load variations.

• Progress in Superconductivity and Cryogenics
• /
• v.5 no.2
• /
• pp.30-35
• /
• 2003

The inductive superconducting fault current limiter (SFCLJ limits the fault current with its dc reactor. To fabricate the optimal dc reactor for inductive SFCL, several design and manufacturing technologies are necessary. In this paper, the manufacturing technology for dc reactor and cryogenic cooling method are described in detail. GM-cryocooler was used enlarge the critical current of dc reactor by cooling down the temperature of dc reactor about 20 K. Moreover, the results of short circuit test were described. Finally, the thermal characteristics of conduction-cooled system were discussed and then, sub-cooled nitrogen system was proposed to enhance the thermal stability of dc reactor.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.7
• /
• pp.590-594
• /
• 2001

The residual DC properties in the in-plane switching (IPS) liquid crystal displays(LCDs) which have different concentrations of cynao NLCs and different resistivities of fluorine NLCs were studied. We also propose a new residual DC measurement method, named 'light minimum/maximum method'. We confirmed the precision of residual DC measurement by light minimum/maximum method compared with the flicker minimizing method and found that new measurement method of residual DC is more accurate than that of the conventional flicker minimizing method since the resolution level of measurements is in 0.1V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.246-246
• /
• 2008

In this work, VOx thin films have been deposited by DC magnetron sputtering method with various DC power. The characterization of the deposited thin films were changed by DC power. The experimental data are obtained on the growth rate and optical and electrical properties of VOx thin films with the increase of DC power. The growth rate. and the surface roughness decrease with DC power. Also, we investigated the electrical and optical properties of VOx thin films using hall measurement, 4-point probe, and UV-visible methods.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.7
• /
• pp.20-28
• /
• 2009

This paper presents the design of zero current switching ZCS pulse frequency modulation type DC-DC converter for magnetron power supply. A magnetron serving as the microwave source in a microwave oven is driven by a switch mode power supply (SMPS). SMPSs have the advantages of improved efficiency, reduced size and weight, regulation and the ability to operate directly from the converter DC bus. The demands of the load system and the design of the power supply required to produce constant power at 4[kV]. A magnetron power supply requires the ability to limit the load current under short circuit conditions. The current source series resonant converter is a circuit configuration which can achieve this. The main features of the proposed converter are an inherent protection against a short circuit at the output, a high voltage gain and zero current switching over a large range of output power. These characteristics make it a viable choice for the implementation of a high voltage magnetron power supply.