• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.293-296
• /
• 2002

This paper proposes new driving methods for designing a driver independent of the current property of organic light emitting diodes (OLED) displays. The proposed methods are the Look-Up Table (LUT) and the Pulse Width Modulation (PWM). The LUT is used to handle the amount of the current for driving the OLED display panel and the PWM is applied to represent the gray scale on the OLED display panel. Segment and common drivers were implemented using delay circuits to prevent short-circuit current and a DC-DC converter was designed to supply the drivers with a power source. In particular, tile proposed methods are used for the manufacturing of 1.8" 128$\times$128 dot passive matrix OLED display panel. The designed circuit was fabricated using 0.6w, 2-poly, 3-metal, CMOS process and applied to the Personal Communication System (PCS) phone successfully.ully.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.2
• /
• pp.109-116
• /
• 2005

The high performance drives of the slotless Permanent Magnet Brushless DC(PM BLDC) motor can be achieved by the current control, where the currents flow according to the rotor position and the current phase is suitably controlled according to the operational condition. Rotor position information can be provided by Hall-IC or sensorless algorithm. So, the Hall-ICs are set up in this motor to detect the main flux from the rotor. Instead of using three Hall-ICs and encoder, this paper uses only two Hall-ICs for the permanent magnet rotor position and the speed feedback signals, and uses a micro-controller of 16-bit type (80C196KC). Also because of low resolution obtained by using Hall-IC even low-cost and simple structure, to improve the wide range of speed response characteristic more exactly, we propose the rotor position signal synthesizer using PLL circuit based on two Hall-ICs.

• Journal of IKEEE
• /
• v.14 no.3
• /
• pp.190-198
• /
• 2010

This paper describes a auto focus piezo actuator driver IC for portable digital camera. The 80[V] DC voltage is generated by a DC-DC converter and supplied to power of piezo moving control circuit. The voltage of piezo actuator needs range -20[V] to 80[V] proportional to 1[Vp-p] input control voltages. The dimensions and number of external parts are minimized in order to get a smaller hardware size. IIC(Inter-IC) interface logic is designed for data interface and it makes debugging easy, test for mass productions. The power consumption is around 40[mW] with supply voltage of 3.6[V]. This device has been fabricated in a 0.6[um] double poly, triple metal 100[V] BCD MOS process and whole chip size is 1600*1500 [$um^2$].

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.9
• /
• pp.14-23
• /
• 2010

This paper reports the fabrication of a DVB-T/H System in Package (SiP) that is able to receive and process the DVB-T/H signal. The DVB-T/H is the European telecommunication standard for Digital Video Broadcasting (DVB). An IC-embedded Printed Circuit Board (PCB) process, interpose a chip between PCB layers, has applied to the DVB-T/H SiP. The chip inserted in DVB-T/H SiP is the System on Chip (SoC) for mobile TV. It is comprised of a RF block for DVB-T/H RF signal and a digital block to convert received signal to digital signal for an application processor. To operate the DVB-T/H IC, a 3MHz DC-DC converter and LDO are on the DVB-T/H SiP. And a 38.4MHz crystal is used as a clock source. The fabricated DVB-T/H SiP form 4 layers which size is $8mm{\times}8mm$. The DVB-T/H IC is located between 2nd and 3rd layer. According to the result of simulation, the RF signal sensitivity is improved since the layout modification of the ground plane and via. And we confirmed the adjustment of LC value on power transmission is necessary to turn down the noise level in a SiP. Although the size of a DVB-T/H SiP is decreased over 70% than reference module, the power consumption and efficiency is on a par with reference module. The average power consumption is 297mW and the efficiency is 87%. But, the RF signal sensitivity is declined by average 3.8dB. This is caused by the decrease of the RF signal sensitivity which is 2.8dB, because of the noise from the DC-DC converter.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.232-237
• /
• 2004

In many application of DC-DC converters, loads cannot be specified in advance, i.e., their amplitudes are suddenly changed from the zero to the maximum rating. Generally, design conditions are changed for each load and then each controller is re-designed. Then, a so-called robust DC-DC converter which can cover such extensive load changes and also input voltage changes with one controller is needed. Analog control IC is used usually for the controller of DC-DC converter. Simple integral control etc. are performed with the analog control IC. However it is difficult to retain sufficient robustness of DC-DC converter by these techniques. The authors proposed the method of designing an approximate 2-degree-of-freedom (2DOF) controller of DC-AC converter. This controller has an ability to attain sufficient robustness against extensive load and DC power supply changes. For applying this approximate 2DOF controller to DC-DC converter, it is necessary to improve the degree of approximation for better robustness. In this paper, we propose a method of designing good approximate 2DOF digital controller which makes the control bandwidth wider, and at the same time makes a variation of the output voltage very small at a sudden change of resistive load. The proposed good approximate 2DOF digital controller is actually implemented on a DSP and is connected to a DC-DC converter. Experimental studies demonstrate that this type digital controller can satisfy given specifications.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.224-225
• /
• 2011

본 논문은 하나의 제어 IC로 이중출력 각각 독립 제어가 가능한 LLC 공진형 컨버터를 제안한다. 기존의 이중출력 LLC 공진형 컨버터의 경우 master 출력전압만 제어가 가능하므로, slave 출력의 정밀제어를 위해 별도의 DC/DC 컨버터가 필요하며, 이는 시스템의 전력 변환 효율을 떨어뜨리고 제작단가를 증가시키는 단점이 있다. 반면, 제안된 회로는 LLC 공진형 컨버터의 이중출력을 하나의 제어 IC로 주파수 및 시비율 각각 가변하는 방식으로 개별적 제어가 가능하므로 부하 및 입력전압 조건과 무관하게 모든 출력 전압의 제어를 정밀하게 할 수 있는 장점이 있다. 따라서 별도의 DC/DC 컨버터 사용이 불필요하므로 고효율 및 저가격의 특징을 가질 수 있다. 본 논문에서는 제안된 회로의 타당성 검증을 위해 이론적 분석결과를 제시하고 40W급 LED 조명회로에 적용한 실험 결과를 바탕으로 그 우수성을 확인한다.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1010-1011
• /
• 2015

최근 고효율 전력변환을 위해 LLC 공진형 하프브릿지 컨버터의 동기정류기에 대한 연구가 활발히 진행되고 있다. 기존 일반적인 다이오드 정류기를 사용하는 경우 출력전류에 비례하는 전력손실이 커서 대전력용으로 사용하기에는 적합하지 않다. 따라서 스위치를 이용한 동기정류기가 검토되고 있는데 동기정류기의 스위치를 구동시키기 위해서는 스위치를 구동시킬 수 있는 구동용 IC가 이용되고 있다. 동기정류기 구동 IC의 단점으로는 약 50%의 중부하 이하에서는 동작되지 않는 단점이 있어 이를 보완하기 위하여 변압기 1차측 전류를 검출하여 게이트 전압을 만들어 스위치를 구동시키는 회로를 제안하였다. 본 논문의 실험 결과 저전력 지점에서 동기정류기가 구동되었고 따라서 전력변환 효율은 기존의 다이오드 정류기에 비해 우수하며 효율개선효과가 있다는 것을 실험으로 보였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.11
• /
• pp.981-987
• /
• 2014

DC/DC switching power converters are commonly used to generate a regulated DC output voltage with high efficiency. The DC/DC converter is composed of a MOSFET (metal-oxide semiconductor field effect transistor), a PWM-IC (pulse width modulation-integrated circuit) controller, inductor, capacitor, etc. It is shown that the variation of threshold voltage and the breakdown voltage in the electrical characteristics of MOSFET occurs by radiation effects in TID (Total Ionizing Dose) testing at the low energy ${\gamma}$ rays using $^{60}Co$, and 5 heavy ions make the gate of MOSFET broken in SEGR (Single Event Gate Rupture) testing. TID testing on MOSFET is accomplished up to the total dose of 40 krad, and the cross section($cm^2$) versus LET(MeV/mg/$cm^2$) in the MOSFET operation is studied at SEGR testing after implementation of the controller board.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.3
• /
• pp.220-227
• /
• 2009

A self oscillation DC/DC converter which has a very desirable characteristics of the high input-output voltage conversion ratio for high voltage DC power supply applications is proposed in this paper. The proposed converter is composed of one power switch, one inductor, several capacitors and diodes. Compared with conventional high-voltage DC/DC converters, it performs the high- voltage power conversion using the inductor instead of the bulky step-up transformer. Therefore, it can reduce the size of magnetic device and save the cost. Moreover, since it needs no control IC by using self oscillation circuit and has lower voltage stress on output diodes, it features a lower cost, simpler structure and more improved performance. Finally, a comparative analysis and experimental results are presented to show the validity of the proposed converter.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.8
• /
• pp.1125-1131
• /
• 2013

Wireless power transmission technology has been studied variety. Recently, wireless power transmission technology used by resonance and magnetic induction field is applied to various fields. However, magnetic resonance and inductive coupling are have drawbacks - power transmission distance is short. Microwave transmission and accept techniques have been developed to overcome short distance. However, improvement in efficiency is required. This paper, propose a high-efficiency microwave energy acceptor IC(EAIC). Suggested EAIC is consists of RF-DC converter and DC-DC converter. Wide Input power range is -15 dBm ~ 20 dBm. And output voltage is boosted up to 5.5 V by voltage boost-up circuit. EAIC can keep the output voltage constant. Available efficiency of RF-DC converter is 95.5 % at 4 dBm input. And DC-DC efficiency is 94.79 % at 1.1 mA load current. Fully EAIC efficiency is 90.5 %.