• 한국전기전자재료학회논문지
• /
• 제16권5호
• /
• pp.385-389
• /
• 2003

There are four main components of the CMP process: polishing pad, slurry, elastic supporter, and pad conditioner. The polishing pad is an essential component to the reproducibility of polishing uniformity in CMP process. However, the polishing pad in recently using metal CMP raised the several points of high cost caused by the increase of cycle time and the many usage of slurry. It is necessary to develop the novel polishing pad which would lead the cost reduction by the higher pad life-cycle, minimized cycle time and lower slurry usage. The characteristics of polishing pad were studied on the effects of different sets of the Polishing pad, which can be applied to metal chemical mechanical polishing process for global planarization of multilevel interconnection structure. The main purpose of this experiment is cost reduction by the increase of pad life-time, the decrease of cycle time and the lower usage of slurry through the specific hard porous structured pad design. It is confirmed that the novel polishing pad made the slurry usage decrease to 60% as well as the pad life-time increase twice with the 25% improvement of removal rate. The polishing time could be decreased and it also helped the cycle time to diminish. It can be expected that this results will help both the process throughput and the device yield to be improved.

• 한국컴퓨터정보학회논문지
• /
• 제21권2호
• /
• pp.97-103
• /
• 2016

This paper deals with the cycle time minimization problem that determines the productivity in printed circuit board (PCB) with n components using the m placement machines. This is known as production cycle time determination problem (PCTDP). The polynomial time algorithm to be obtain the optimal solution has been unknown yet, therefore this hard problem classified by NP-complete. This paper gets the initial assignment result with the machine has minimum unit placement time per each component firstly. Then, the balancing process with reallocation from overhead machine to underhead machine. Finally, we perform the swap optimization and get the optimal solution of cycle time $T^*$ within O(mn) computational complexity. For experimental data, the proposed algorithm can be obtain the same result as integer programming+branch-and-bound (IP+B&B) and B&B.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제11권4호
• /
• pp.433-445
• /
• 2011

Duty cycle is determined as the ratio of operating time to total time. Duty cycle in reliability prediction is one of the significant factors to be considered. In duty cycle application, non-operating time failure rate has been easily ignored even though the failure rate in non-operating period has not been proved to be small enough. Ignorance of non-operating time failure rate can result in over-estimated system reliability calculation. Furthermore, utilization of duty cycle in reliability prediction has not been evaluated in its effectiveness. In order to address these problems, two reliability models, such as MIL-HDBK-217F and RIAC-HDBK-217Plus, were used to analyze non-operating time failure rate. This research has proved that applying duty cycle in 217F model is not reasonable by the quantitative comparison and analysis.

• 한국경영과학회지
• /
• 제23권4호
• /
• pp.53-61
• /
• 1998

In this paper, we take into consideration the optimal cycle time in a kanban system. Even though there are many studios in the literature published in the past. It is rare to fine a paper dealing with kanban cycle time. We consider manufacturing structure configured in the real field and suggest kanban cycle time for the cases of linear, tree assembled, distributed, general and mixed structures. Also we give numerical example for each structure.

• 산업경영시스템학회지
• /
• 제5권7호
• /
• pp.17-24
• /
• 1982

Most line balancing technique widely used in manufacturing industry is done by balancing to a cycle or operator, time determined to provide the exact number of required units per day. No thought is given to benefit foregone by making slight changes to cycle time to achieve better distribution of the work among operators. This study provides a method to minimize balance delay by the choice of cycle time.

• 조명전기설비학회논문지
• /
• 제18권6호
• /
• pp.191-196
• /
• 2004

이 논문에서는 버스시스템의 성능 평가를 위한 순환시간의 계측방법이 제안 되었다. 센서와 엑튜에이터가 주를 이루는 생산시스템에서 순환시간은 버스시스뎀의 성능평가의 중요한 파라미터이다. 순환시간을 계측하기 위하여 제안된 방법은 간단한 알고리즘의 구성에 기반을 두었으나 주변기기나 PLC의 내부에 존재하는 지연요소들을 고려 해야만 한다. 계측결과의 개선을 기하기 위해 시험방법은 최적, 최저의 경우로 나누어 이에 대응되는 파라미터를 구성하여 값을 설정한다. 수학적인 모델을 기반으로 필드버스 시스템의 순환시간에 대한 계측을 통해 제안된 방법이 효율적임을 입증하였다. 그 결과로서 제안된 방법의 간편성과 편리함으로 인해 순환시간의 측정에 요구되는 엔지니어링 비용과 시간을 절감할 수 있었다.

• 대한교통학회지
• /
• 제10권3호
• /
• pp.7-20
• /
• 1992

The common cycle time for the linded signals is usually determined for the critical intersecion, just because the cpacity of a signalized intersection depends on the cycle time. This may not be optimal since the interactions between the flow and the spatial structure of the route or the area are disregarded in this case. It is common to separate the total delay incurred at signals into two parts, a deterministic or uniform delay and a stochastic or random delay. The deterministic delays and the stochastic delays on the artery particularly related to signal cycle time. For this purpose a microscopic simulation technique is used to evaluate deterministic delays, and a macroscopic simulation technique based on the principles of Markov chains is used to evaluate stochastic delays with over flow queue. As a result of investigating the relations between deterministic delays and cycle time in the various circumstances of spacing of signals and traffic volume. As for stochastic delays the resalts of comparisons of the macroscopic simulation and Newell's approximation with the microscopic simulation indicate that the former is valid for the degree of saturation less than 0.95 and the latter is for that above 0.95. Newell's argument that the total stochastic delay on an arterial is dominated by that at or caused by critical intersection is certified by the simulation experiments. The comprehensive analyses of the values of optimal cycle time with various conditions lead to a model. The cycle time determined by this model shows to be approximately 70% of that calculated by Webster's.

• 한국산림과학회지
• /
• 제101권3호
• /
• pp.344-355
• /
• 2012

임목수확작업시스템 구축과 효율적인 임목수확작업 기술을 보급하기 위해 타워야더 및 스윙야더 등에 의한 전목집재작업시스템과 굴삭기 그래플 등에 의한 단목집재작업시스템의 작업시간 및 공정을 분석하였다. 전체 조사작업시간을 기준으로 분석한 1 cycle당 작업시간은 전목집재작업시스템에서 체인톱에 의한 벌목 46.6초/cycle, 타워야더에 의한 집재 480.6초/cycle, 스윙야더에 의한 집재 287.4초/cycle, 체인톱에 의한 조재 155.14초/cycle로 나타났다. 또 한 단목집재작업시스템에서는 체인톱에 의한 벌목 및 조재 225.65초/cycle, 굴삭기 그래플에 의한 단목집재 4,972초/cycle, 지엽집재 3,143초/cycle로 나타났으며, 바퀴식 미니포워더에 의한 소운재 4,688초/cycle, 굴삭기 그래플 및 소형운재차에 의한 소운재 2,118초/cycle로 나타났다. 전목집재작업시스템의 작업공정에서 체인톱에 의한 평균 벌목공정이 $57.89m^3$/일, 타워야더에 의한 평균 집재공정이 $20.3m^3$/일, 스윙야더에 의한 평균 집재공정이 $31.55m^3$/일, 체인톱에 의한 평균 조재공정이 $20.3m^3$/일로 나타났다. 또한, 단목집재작업시스템의 작업공정에서 체인톱에 의한 평균 벌목 및 조재공정이 $11.96m^3$/일, 굴삭기 그래플에 의한 평균 단목집재공정이 $34.75m^3$/일, 굴삭기 그래플에 의한 평균지엽수집공정이 $37.66m^3$/일, 굴삭기 그래플에 의한 평균 작업로의 개설공정이 73.8 m/일로 나타났으며, 바퀴식 미니포워더와 굴삭기 그래플 및 소형 운재차에 의한 평균 소운재 작업공정이 각각 $15.73m^3$/일과 $65.03m^3$/일로 나타났다.

• Architectural research
• /
• 제7권2호
• /
• pp.69-79
• /
• 2005

There are no formal decision tools or guidelines to assist owners and contractors in choosing delivery systems and project strategies that would allow for a radical reduction in project cycle time - from the preplanning phase through project start up. Therefore, it is important to identify the state-of-practice and the state-of-art on methods of achieving radical reduction defined as a reduction of 25% or more in overall project cycle time. A comprehensive literature review, three questionnaire surveys, and the seven case studies were conducted and the data obtained from them were analyzed to establish the state-of-practice and state-of-art for project cycle time reduction techniques.

• Journal of Welding and Joining
• /
• 제14권1호
• /
• pp.38-46
• /
• 1996

High temperature low cycle fatigue crack growth behavior is investigated over a range of two temperatures and various frequencies in SUS 304 stainless steel. It is found that low frequency and temperature can enhance time-dependent crack growth. With high temperature, low frequency and long crack length, ${\Delta}J_c/{\Delta}J_ f$, the ratio of creep J integral range to fatigue J integral range is increased and time-dependent crack growth is accelerated. Interaction between ${\Delta}J_f$ and ${\Delta}J_c$ is occured at high frequency and low temparature and ${\Delta}J_c$, creep J integral range is fracture mechanical parameter on transition from cycle-dependent to time dependent crack growth in creep temperature region.