• Journal of Biosystems Engineering
• /
• 제19권4호
• /
• pp.311-317
• /
• 1994

Warts and barks of apple trees were vector of White rot. Two devices removing warts and barks for the use of pest control on apple trees were developed and evaluated in this study, and their results are as follows ; 1. A total of 148 warts were examined to determine the average size. About 35 percent of the examined warts were 6~8mm long, 4~8mm wide and 4~6mm thick in size. About 30 percent of the examined warts were 4~6mm long, 2~4mm wide and 6~8mm thick in size. 2. Seventy-one percent of the examined barks removed were 4~8mm in thickness. 3. A blade with 30 degree of cutting angle required 3 to 22 percent less cutting energy than those with 15 and 45 degrees of cutting angles. 4. The cutting torque decreased from 31 N-cm to 12 N-cm with an increase of cutting speed from 26cm/s to 104cm/s for a feeding speed of 0.31 mm/s with the blade angle of 30 degrees. 5. The cutting torque increased from 6N-cm to 32N-cm with an increase of branch diameter from 6mm to 14mm for a feeding speed of 0.31 mm/s with the blade angle of 30 degrees. 6. Two devices mounted on a mower for removing warts and barks were evaluated and proved effective.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.1068-1072
• /
• 1997

This work deals with on investigation the influence of various additives to a base stock cutting fluid in order to develop a better deep hold drilling. This investigation has been aiming at developing an oil which gives a maximum cutting efficiency at a minimum wear rate of the tool and the guiding pads. The purpose of study is to analyze how guide pad of tools, workpiece and the change of contained quantity of extreme pressure additive in cutting fluids have effects on the hold over size of cutting hole, surface roughness of workpiece,wear rates of guide pad and roundness during the deep hole machining of SM55C with solid BTA drill by using BTA drilling system through experiment. Conclusion reached is as follows. It has been proved that the contained quantity of surphur more affects machinability than that of extreme pressure additive of chlorine of cutting fluid in BTA drilling during Deep Hole Drilling. Considering its base oil, the the contained quantity of extreme pressure assitive of surphur can be different, but it's judged that the range of 1.5 ~ 2.0% is suitable to machinability for workpiece in BTA drilling. Regarding guide pad, it's judged that the reduction of wear is possible in propotion to the contained quantity of exrreme pressure additive of chlorine against supporting of cutting force and Bumishing operation of machining parts in cutting.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.987-992
• /
• 1997

Burrs always come out with the machining of ducterial with small size. Though the size of burrs is small, burrs dominate deterioration of the accuracy of the micro grooves. So the burr generation model especially side burr generation model was investigated to predict the size of the burrs at the given cutting conditions. The side shear plane is introduced to build the burr generation model and the width of side shear plane nomalized with cutting depth is defined with the shear angle. From the theoretical observation, the width of side shear plane can vary up 40% of the cutting depth. To determine the size of burr and stiffness, single groovings were carried out and it was found that there exist a critical depth of cut that the size or stiffness of the burr vary.

• Design & Manufacturing
• /
• 제17권2호
• /
• pp.9-14
• /
• 2023

In this study, an experiment was conducted to confirm the applicability of the external shape control of the ultrasonic knife to the CFRTP material, which is the base material of thermoplastic. TC910 based on polyamide6 (PA6) was used as the material. The slope 와 and tool transfer speed of the material and tool were selected as process factors for processing, and the following results were obtained. Under all cutting conditions using an ultrasonic knife, friction heat caused by high-frequency vibration was issued at 150℃ at the contact part between the material and the knife during cutting. As a result of the cutting force analysis, the faster the transfer speed, the higher the cutting force as the angle of entry of the blade increased, and the size of the cutting force changed during cutting. As for the size of the burr in accordance with the transfer speed condition, the smallest burr occurred at 150mm/min in the side part, and the smallest burr occurred at 150mm/min and 200mm/min in the case of the outlet burr. The size of the burr according to the entry angle tended to decrease as the tool entry angle increased, and the side part tended to increase as the tool entry angle increased. As a result of the cutting surface analysis, it was confirmed that the base material was eluted under all conditions, and the faster the transfer speed, the lower the elution phenomenon of the base material. Based on the above results, cutting the CFRTP material with an ultrasonic knife is possible, but the effect on heat generation caused by friction needs to be minimized, and further research needs to be conducted on this.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1996년도 International Conference on Agricultural Machinery Engineering Proceedings
• /
• pp.1031-1040
• /
• 1996

Spawn bottle cutting and spawn cake shredding machine has been developed to save the farm labor and operating cost for mushroom growing farmers. The prototype can cut the bottom and side of the bottle while shredding the spawn cake by one farmer. The cutting plastic shell is done by two couples of high speed disc saws that can cut cross section and lengthwise two side of the bottle, while spawn cake shredding is done by spike teethed rotating drum and wiremesh concave. The optimum speed of cutting disc saw was observed 1.700rpm both the cross cutting saw and lengthwise cutting saw in consideration of the cutting accuracy. And the location for the instalation of cross cutting disc saw was considered as around 4 mm above the table bottom , while the optimum clearance between two edges of lengthwise cutting disc saw was showed 86mm. For the sawdust spawn cake shredder , proper size of spawn sawdust granule was observed in the 15 x 15mm size withmesh concave with the shredding rum speed of 500rpm. The prototype can be reduce 73 per cent of working hours with the working cost reduction of 49 per cent compare with those of conventional operation.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 봄 학술발표회 논문집
• /
• pp.585-591
• /
• 1997

The purpose of this experiment is to verify and efficiency of repair for cutting area. The result of this experiment is the fact thar the strength of compression and bending in declined by width and depth of cutting area. Deterioration of strength depends on depth to be repair area the strength of compression decreased up 50% when the repairing area is the fact that it is emerged by the increased of depth size rather than width size.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.1012-1015
• /
• 2001

The purpose of this paper is to evaluate the specific cutting energy characteristics during turning SM45C steel. Using the orthogonal array method the specific cutting energy has been predicted. And the significance of the equation is checked by ANOVA test. Predicted values of specific cutting energy are well concide with the measured ones. When the feed rate becaomes larger than 0.5mm/rev, predicted specific cutting energy increases.

• 한국산업융합학회 논문집
• /
• 제7권1호
• /
• pp.55-62
• /
• 2004

The presence of cutting fluid for cutting tool and workpiece leads a temperature decrease, and reduces tool wear and residual stress. Moreover, it disposes chips from cutting area, and reduces thermal distortion. However, in manufacturing, cutting fluid used in cutting process is undesirable for both human and environmental aspect. Also, it's not economic for cutting cost. This paper studied experimentally the effects of cutting parameters on the characteristics of mist generation in turning. The results of experiment are as follows: 1) The more severe cutting conditions the more mist generate, 2) The ratio of weight concentrations of cutting fluid nearly have no an effect on the amounts of mist generation 3) The size of SMD is not affected by cutting parameters.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.985-988
• /
• 1997

In end milling process, the undeformed chip section area and cutting forces vary periodically with phase change of the tool. However the real undeformed chip section area deviates from the geometrically ideal one owing to cutter runout and tool shape error. In this study ,a method of estimating the real undeformed chip section area which reflects cutter runout and tool shape error was presented in up end milling process using measured cutting forces. Size effect was identified from the analysis of specific cutting resistance obtained by using the modified undeformed chip section area.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.911-914
• /
• 1997

This Experiment was carried out for bur minimization in drilling. New drill geometries are proposed to minimize the burr formation in drilling operation. Three types of drills are made, champer, round and step drill. The burr formed in first cutting by front cutting edge ca be removed in second cutting by the cutting edges in chamfer, round edge and step. New burrs are formed by second cutting and can be minimized according to the change of drill geometry like, chamfer size and angle, corner radius in round drill and step size and angle in step drill. To measure the burr formed in drilling, laser sensor is used.