• 설비공학논문집
• /
• 제17권5호
• /
• pp.427-435
• /
• 2005

This paper investigates the thermal storage performance of the office building which has adopted an air conditioning system with its slab structure as a regenerator. Four cases of the thermal storage performance experiment were conducted. Room air temperatures, floor slab temperatures, temperatures around the air conditioning unit were logged and analyzed. The load handling capacity of the air conditioning unit and the amount of heat stored in the slab were decided from those experiments. Several efficiencies were investigated to evaluate the performance of the thermal storage. The results concluded that the slab as a regenerator is very effective in cutting down peak loads of the office building.

• 한국정밀공학회지
• /
• 제5권4호
• /
• pp.32-38
• /
• 1988

Apaptive cintrol of machine tool is aimed to change cutting state satis- factorily without aid of a machine operator, if the cuting state is abnomal such as formation of tangled ribbon type chip, built-up edge and generation of chattering and so on. Among these the recognition of chip type is one of the most important since it has imlications relate to : 1. Safety of operator 2. Stoppage of work due to entanglment in tool and workpiece of chip 3. Problem of producted chip control In this paper the chip type is discriminatied by the pattern recognition technique. It is found that the power spectrum of cutting force for each chip type has it's own special pattern. Linear discriminant function for the recognition of the chip type is obtained by learning process. The discriminant function can be the basis of adaptive control for the rate of success of recognition by pattern recognition technique is at leasthigher than 83%.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2006년도 전력전자학술대회 논문집
• /
• pp.158-162
• /
• 2006

A lot of pieces of iron plate are used to build a ship. The states of cutting surface of iron are however bended or ununiformly cuttled by cutting machine. These may cause bad Quality of painting, and shorter lifetime of iron by rust. In this paper, a new approach of grinding force control method which teaching of robot is not required is proposed to avoid long preparation time of robot and to improve the productivity. The way used in this paper is just like a blind man works through the road with stick only.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 전력전자학술대회 논문집
• /
• pp.352-356
• /
• 1998

This paper is a study about Ac servo motor position and speed control characteristics which depend on feedforward control, the acceleration / deceleration time constant after the interpolation, and PI control, automatic deceleration at corner in order to shape cutting control of feed drive system of the machine tool. The shape error caused by delay of the servo system in the direction of radius at the time of circular cutting is reduced by feedforward control. The shape error generated by the position command delay is minimized by using the acceleration / deceleration time constant after the interpolation. The results were verified to optical machining center experimentation of the machine tool.

• 한국정밀공학회지
• /
• 제1권1호
• /
• pp.34-49
• /
• 1984

The stability of machine tool systems is analyzed by considering the machining process as a stochastic process without decomposing into machine tool structural dynamics and cutting processes. In doing so the time series analysis technique developed by Wu and Pandit is applied systematically to the relative vibration between cutting tool and work- piece measured under actual working conditions. Various characteristic properties derived from the fitted ARMA(Autoregressive Moving Average) Models and those from raw data directly are investigated in relation with the system stability. Both damping ratio and absolute value of the characteristic roots of the AR part of the most significant dynamic mode are preferred as stability indicating factors to the other pro-perties such as theoretical variance .gamma. (o) or absolute power of the most dominant dynamic mode. Maximum aplitude during a certain interval and variance estimated from raw data are shown to be very sensi- tive to the type of the signal and the location of measurement point although they can be obtained rather easily. The relative vibration signal is also analyzed by FFT(Fast Fourier Transform) Analyzer for the purpose of comparison with the spectrums derived from the fitted ARMA models.

• Journal of Biosystems Engineering
• /
• 제19권3호
• /
• pp.175-184
• /
• 1994

This study was conducted to investigate experimentally the basic characteristics of the torque of the cutterbar driving shaft as the double-knife was used instead of the conventional standard single-knife type. A new design for inclined setting of the cutterbar relative to the direction perpendicular to combine harvester movement was investigated to test a possible reduction of concentrated load caused by the simultaneous cutting of many rows. It was evaluated that the maximum torque and mean total power of the driving shaft due to the cutting resistance of the rice straw were largely depended upon the rotational shaft-speed and straw feeding rate, but were resepectively 1.1~2.3 and 1.15~1.34 times higher compared to those while idling. It was also proved that the inclined setting of the cutterbar could save a considerable amount of energy required for its driving shaft.

• 한국정밀공학회지
• /
• 제15권11호
• /
• pp.233-243
• /
• 1998

The demand of high speed machining is increasing due to the high speed cutting and grinding provides high efficiency of process, short process time, improved metal removal capacity and better surface finish. Active magnetic bearings allow much high surface speed than conventional ball bearings and therefore greatly suitable for high speed cutting or grinding. This paper describes a design process of an active magnetic bearing system for a high speed grinding spindle with power 5.5kW and maximum speed 60,000rpm. Magnetic actuators are designed by the magnetic circuit theory considering static load condition, and examined with FEM analysis. Dynamic characteristics are also considered, such as bandwidth, stiffness, natural frequency and static deflection. System characteristics are simulated with a rigid rotor model.

• ETRI Journal
• /
• 제35권1호
• /
• pp.158-161
• /
• 2013

This letter proposes a low-power current-steering digital-to-analog converter (DAC). The proposed DAC reduces the clock power by cutting the clock signal to the current-source cells in which the data will not be changed. The 10-bit DAC is implemented using a $0.13-{\mu}m$ CMOS process with $V_{DD}$=1.2 V. Its area is $0.21\;mm^2$. It consumes 4.46 mW at a 1-MHz signal frequency and 200-MHz sampling rate. The clock power is reduced to 30.9% and 36.2% of a conventional DAC at 1.25-MHz and 10-MHz signal frequencies, respectively. The measured spurious free dynamic ranges are 72.8 dB and 56.1 dB at 1-MHz and 50-MHz signal frequencies, respectively.

• 한국연소학회지
• /
• 제22권4호
• /
• pp.35-42
• /
• 2017

This case covers the issues related to the operation problem, cause analysis and improvement cases of the FGD that employed the non-leakage type GGH in coal-fired power plant for the first time in Korea. In the Cooler, there was a main problem that the tube is damaged by the ash cutting due to the high velocity of flue gas in the duct and by the weak wear resistance of material. In the Reheater, there was a main problem that the tube was corroded due to chlorine and sulfur in the circumstance of the low temperature. In order to solve those problems, we have improved the Reheater tube and tube fins by coating enamel to reduce corrosion rate.

• Nuclear Engineering and Technology
• /
• 제55권1호
• /
• pp.45-51
• /
• 2023

During the operation of a nuclear power plant (NPP), the waste reactor vessel closure head (RVCH) that is replaced owing to design or manufacturing defects is buried in a designated area or temporarily stored in a radiation shielding facility within the NPP. In such cases, storing it for extended periods proves a challenge owing to space constraints in the power plant and a safety risk associated with radiation exposure; therefore, dismantling it quickly and safely is crucial. However, not much research has been done on the dismantling of the RVCH in an operational power plant. This study proposes a dismantling process based on the radioactive contamination level measured for the Kori #1 RVCH, which is currently being discarded and stored, and examines the decontamination and cutting according to this process. In addition, the amount of secondary waste and dismantling cost are evaluated, and the dismantling effect of the reactor closure head is analyzed.