• Tunnel and Underground Space
• /
• v.21 no.3
• /
• pp.192-204
• /
• 2011

In this study, 3-D analyses were conducted while taking every construction stage into account. Then 2-D analyses were conducted which yield the same results with the 3-D results. The crown settlement normalized by the ultimate value was compared during the process to overcome the discrepancy caused by different dimensions. When a bench or a core is left uncut to give extra support to the face and eventually the whole excavation boundary, this extra supporting effect also has to be included in the analysis. In this study, this effect is also implemented in terms of the load distribution factor. When the length of the bench is very short compared to the diameter of the tunnel in such cases as in short bench cut or in mini-bench cut, the supporting effect of the face does not disappear even after the bench is completely excavated and supported since the face is still too close to the point of interest. The 4th load distribution factor was defined to stand for the advance of the face after the completion of the excavation cycle. The 4th load distribution factor turned out to be very useful in determining the load distribution factors when a tunnel is excavated by bench cut with various bench lengths under different initial conditions.

• Journal of Industrial Technology
• /
• v.26 no.B
• /
• pp.73-81
• /
• 2006

A sensitivity analysis about effects of influencing factors on the stability of Soil cut slope was performed. Slope stability analyses were carried out under dry, rainy and seismic conditions. Dominant factors controlling the slope stability were chosen such as cohesion and internal friction angle, unit weight of soil, water table and seismic horizontal coefficient used for the slope stability during earthquake. Parametric stability analysis with those factors was performed for sensitivity analysis. As results of analyzing the sensitivity of factors under dry and rainy conditions, effects of cohesion, internal friction angle and unit weight of soil on the stability of slope are more critical in the dry condition than in the rainy condition. Cohesion and internal friction angle are more dominant factors influencing the slope stability irrespective of dry or rainy conditions than unit weight of soil and the horizontal seismic coefficient. The unit weight and the horizontal seismic coefficient affects crucially the stability according to conditions of slope formation and dry or rainy seasons. For the effect of horizontal seismic coefficient on stability of slope, safety factor of slope is not affected significantly by dry or rainy conditions. However, increase of the horizontal seismic coefficient under the rainy condition floes reduce the safety factor significantly rather than the dry condition. Therefore, it is needed that the location of the water table is assigned appropriately to satisfy the required safety factor of stability in the case of checking slope stability for the rainy and seismic conditions.

• Journal of Microbiology and Biotechnology
• /
• v.9 no.3
• /
• pp.328-333
• /
• 1999

Susceptibility of 61 strains of Helicobacter pylori to metronidazole was examined by both the disk diffusion method using a cut-off of 15㎜ for resistance and the E test with a cut-off of 8㎎/l. The MIC/sub 50/ and MIC/sub 90/ by the E test were 2 ㎎/l and 256㎎/l, respectively. Metronidazole resistance was found in 22 (36％) out of the 61 H. pylori strains by the E test and in three additional strains by the disk diffusion method. Amongst the latter three isolates, the MICs by the E test were 4 ㎎/l, 6㎎/l, and 6㎎/l, respectively. These figures are one log₂ or half log₂ dilution lower than the cut-off of 8㎎/l recommended as resistance for the E test. All 22 metronidazole resistant H. pylori isolates by the E test that were subjected to random amplified polymorphic DNA (RAPD) fingerprinting showed different DNA fingerprints. Interestingly, >90％ of resistant isolates possess two common DNA bands of 0.4 and 0.9 kb. This study demonstrates that the results of the disk diffusion method for testing H. pylori susceptibility to metronidazole correlates well with that of the E test. The criteria for interpretation need to be internationally standardized so that the results from different centers can be compared.

• Tunnel and Underground Space
• /
• v.13 no.2
• /
• pp.125-137
• /
• 2003

Field measurements were carried out in this study to investigate the behavior of cut and cover tunnel such as the distribution and the magnitude of the earth pressure during back fill process. Three kinds of measuring instruments, such as the earth pressure load cell, the concrete strain gauge and the reinforcing bar meter of embedded type in concrete structure were installed and measured. Earth pressure load cells measured the outside forces acting on the tunnel lining with radial directions. Three load cells were installed at the crown, the right and the left shoulder of the tunnel, respectively. Three sets of reinforcing bar meter were installed in the double reinforcements of the tunnel lining and their locations were the same with the position of the earth pressure load cells. Concrete strain gauge was installed only one site of the upper compressive part at the tunnel crown. Based on the measurements, the deformation and the earth pressure acting on the tunnel lining were investigated with the back fill process. Considerations on the validity of the field measurements were paid.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.6
• /
• pp.1456-1464
• /
• 1993

The achievable machining accuracy depends upon the level of the micro-engineering, and the dimensional tolerances in the order of 10 nm and surface roughness in the order of 1 nm are the accuracy targets to achieved today. Such requirements cannot be satisfied by the conventional machining processes. Single point diamond turning is one of the new techniques which can produce the parts with such accuracy limits. The aims of this thesis are to get a better understanding of the complex cutting forces. A cutting model for describing the influence of cutting conditions (cutting speed, feedrate and depth of cut), material properties of the workpiece and tool geometry has been proposed after estimating the two cutting force models-the Recht model and the Dautzenberg model. The experiments with Al-alloy workpieces, which have been carried out in order to estimate the models, show that the proposed model in this thesis is better than the two models. As the depth of cut and feedrate are increased in the operations settings (depth of cut 8-100$\mu{m}$, feedrate 8-140$\mu{m}$/rev, and cutting speed 8 m/sec), the relation of dimensionless cutting forces from experiments are similar to the proposed model. With the undeformed chip area of $30-80{\times}10^{2}$\mu{m}^2$, the experimental cutting forces accord with the force prediction.

• Asian Journal of Turfgrass Science
• /
• v.18 no.1
• /
• pp.29-36
• /
• 2004

The efficient refinement of seed is required to reduce the cost and labor input in artificial propagation of wild plant. This study was carried out to develop methods for collecting and refining tiny seeds from wild plants. For obtaining Phragmites communis seeds, the inflorescence was cut into small fragments using a Straw Cutter and subsequently detached pappus hairs from seed coat by Hammer Mill. The primary refined seeds were passed 1.0 mm sieve. The screened seeds were subjected to Seed Blower with wind speed of 0.25 mㆍsec-1 to collected intact and well-ripen seeds. The seeds of Imperata cylindrica were refined as follows. Inflorescences were cut using a Straw Cutter first. The pappus was removed from cut fragments using a Hammer Mill and subsequently subjected to Seed Scarifier at 500rpm for 60 sec. for further separation. The separated seeds were passed 1.0 mm screen and collected after blowing with Seed Blower of wind speed of 0.15 mㆍsec-1. When the amount of seed was too little to refine with Seed Scarifier and Blower, the procedure was slightly modified from the procedure described above. The crude seed mixture obtained from Hammer Mill step was hand-refined roughly and then immersed into cone. (95%) sulfuric acid for 2 min. and collected floating portion after dilution of sulfuric acid solution 100 times with tap water. The collected seeds were dried and passed 0.149 mm sieve. During seed refining process using mechanical or sulfuric acid treatments, a small portion of damaged seed were evolved, however, the amount was not noticeable as compared to the total amount of collected seeds. Because the germination percentages between hand-refined seeds and seeds refined by above methods were not statistically different, the developed procedures for refining tiny seed of wild plants are helpful to reduce the cost and labor input in artificial propagation of two species.

• Journal of Digital Convergence
• /
• v.16 no.10
• /
• pp.479-484
• /
• 2018

This study is an attempt to analyze the changes and morphological analysis of the one length hair style of women in the Imperial Japanese colonial period, and the purpose of this study is to analyze the components of hair design such as shape, texture, and color based on the precedent and the book and to make possible various styles of one length hair style cut. From the results of this study, one length hair style showed the outline shape with no step height of cut length, natural hair texture and natural hair color in 1910s to 1920s. In the 1930s, the one length hair style showed a slight cut length step height and a slight discoloration using a diamond shape, a narrow wave of natural texture, hydrogen peroxide or oxygenated water. In the 1940s, one length hair style did not find any singularity to pursue brilliant beauty(美) in terms of form, texture, and color. This study may enable a deep and detailed follow up study on one length hair style, and will be a cornerstone for the development of basic data of hair beauty education and trend of new mode.

• Journal of Environmental Science International
• /
• v.11 no.2
• /
• pp.111-120
• /
• 2002

Asian dust(or yellow sand) occurs mainly in spring and occasionally in winter in east Asia, when the weather conditions are under an upper trough/cut-off low and surface high/low pressure system during blocking episode days associated with the stationary patterns of the upper level jet stream. The transport mechanism for Asian dust during the blocking episode days in spring 2001 was analyzed using the TOMS aerosol index and meteorological mesoscale model 5(MM5). Based on the E vector, an extension of an Eliassen-Palm flux, the blocking episode days were found to be associated with the development of an upper cut-off low and surface cyclones. Concurrently, the occurrence of dust storms was also determined by strong cold advection at the rear of a jet streak, which exhibited a maximum wind speed within the upper jet stream. As such, the transport mechanism for Asian dust from China was due to advection of the isentropic potential vorticity(IPV) and isentropic surfaces associated with tropopause folding. The transport heights for Asian dust during the blocking episode days were found to be associated with the distribution of the isentropes below the IPV At the same time, lee waves propagated by topography affected the downward motion and blocking of Asian dust in China. The Asian dust transported from the dust source regions was deposited by fallout and rain-out with a reinforcing frontogenesis within a surface cyclone, as determined from satellite images using TOMS and GMS5. Accordingly, these results emphasize the importance of forecasting jet streaks, the IPV, and isentropes with geopotential heights in east Asia.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.45 no.3
• /
• pp.30-36
• /
• 2008

The multimedia that is characterized by multi-media, multi-features, multi-representations, huge volume, and varieties, is rapidly spreading out due to the increasing of application domains. Thus, it is urgently needed to develop a multimedia information system that can retrieve the needed information rapidly and accurately from the huge amount of multimedia data. For the content-based retrieval of moving picture, picture information is generally used. It is generally used when video is segmented. Through that, it can be a structural video browsing. The tasking that divides video to shot is called video segmentation, and detecting the cut for video segmentation is called cut detection. The goal of this paper is to divide moving picture using HMMD(Hue-Mar-Min-Diff) color model and edge histogram descriptor among the MPEG-7 visual descriptors. HMMD color model is more familiar to human's perception than the other color spaces. Finally, the proposed retrieval system is implemented as hardware.

• Journal of the Korean Society for Railway
• /
• v.19 no.2
• /
• pp.213-223
• /
• 2016

Traffic jams occur frequently due to the dense populations of cities. Accordingly, the discomfort of citizens has increased. In order to minimize traffic inconveniences, various public transportation facilities have been suggested. In this paper, for the economical construction of a near-surface railway system, the design of a trench shield is developed and a review of its applicability is done by creating and testing trench shield equipment on a small scale. The trench shield consists of an excavation part, a shield part and an advancement part. To examine the applicability of the trench shield, a laboratory test is carried out. The results of the laboratory test confirm the possibility of reducing the construction time at open-cut construction sites through the excavation of the trench shield. Although the laboratory test is an indoor and relatively small-scale experiment, it is considered to be possible to secure a construction speed of 3m/day when the trench shield equipment is used.