• Korean Journal of Materials Research
• /
• v.23 no.12
• /
• pp.737-744
• /
• 2013

We demonstrated size control of Au nanoparticles by heat treatment and their use as a catalyst for single-walled carbon nanotube (SWNTs) growth with narrow size distribution. We used uniformly sized Au nanoparticles from commercial Au colloid, and intentionally decreased their size through heat treatment at 800 oC under atmospheric Ar ambient. ST-cut quartz wafers were used as growth substrates to achieve parallel alignment of the SWNTs and to investigate the size relationship between Au nanoparticles and SWNTs. After the SWNTs were grown via chemical vapor deposition using methane gas, it was found that a high degree of horizontal alignment can be obtained when the particle density is low enough to produce individual SWNTs. The diameter of the Au nanoparticles gradually decreased from 3.8 to 2.9 nm, and the mean diameter of the SWNTs also changed from 1.6 to 1.2 nm for without and 60 min heat treatment, respectively. Raman results reconfirmed that the prolonged heat treatment of nanoparticles yields thinner tubes with narrower size distribution. This work demonstrated that heat treatment can be a straightforward and reliable method to control the size of catalytic nanoparticles and SWNT diameter.

• Journal of applied mathematics & informatics
• /
• v.7 no.2
• /
• pp.493-506
• /
• 2000

Recently the first author and his coworker report a new finite element method for the Poisson equations with homogeneous Dirichlet boundary conditions on a polygonal domain with one re-entrant angle [7], They use the well-known fact that the solution of such problem has a singular representation, deduced a well-posed new variational problem for a regular part of solution and an extraction formula for the so-called stress intensity factor using tow cut-off functions. They use Fredholm alternative an Garding's inequality to establish the well-posedness of the variational problem and finite element approximation, so there is a maximum bound for mesh h theoretically. although the numerical experiments shows the convergence for every reasonable h with reasonable size y imposing a restriction to the support of the extra cut-off function without using Garding's inequality. We also give error analysis with similar results.

• Proceedings of the IEEK Conference
• /
• 2004.06b
• /
• pp.541-544
• /
• 2004

This paper presents a new circuit panitioning algorithm using wire redundancy removal. This algorithm consist of the two steps. In the first step. We propose a new IIP(Iterative Improvement Partitioning) technique that selects the method to choice cells according to improvement status using two kinds of bucket structures, the one kept by total gain, and the other by updated gain. In the second step, we select the target wire in the cut-set. We add a alternative wire in the circuit to remove the target wire. For this we use wire redundancy removal and addition method The experimental results on MCNC benchmark circuits show improvement up to $41-50\%$ in cut-size over previous algorithms

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.12
• /
• pp.71-77
• /
• 1999

In this study, Cu ferrite was machined with cermet tool to clarify the machinability. The main conclusions obtained were as follows. The tool wear becomes the smallest at the cutting speed of 90m/min with the depth of cut of 0.2mm. The surface roughness becomes larger with increasing the cutting speed and the chamfer angle. The tool with the chamfer angle of $15{\circ}$ shows the best performance. The surface roughness increases almost proportionally with the increase of the chip size. The tool wear decreases with increasing feed in the depth of cut not more than 0.2mm.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.4 no.2
• /
• pp.243-248
• /
• 2001

The present work is described the design factors and separation mechanism of ridge-cut explosive bolt in order to optimize the stage separation characteristics. Characteristics of test samples would differ depend on the detonating devices, the shape and size of bolt body, the amount of loading explosives, and the confinment conditions of bolt. Based on the results from these experimental factors, it appears to optimal condition of ridge-cut explosive that the amount of loading explosive seems to be near 110mg of RDX, the height of loading explosive is 3.5mm, the thickness of bolt is 3.9mm, and the degree of ridge is approximately $120^{\circ}$

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2001.09a
• /
• pp.216-219
• /
• 2001

In this study, a hydrocyclone operated by centrifugal force was examined as a part of dredge system of lake sediments. It does not help dehydration of the sediments, but also enables the classification of fine particles in the stable and sanitary treatment. Several experiments were performed focusing on the separation efficiency under the condition of room temperature with virtual sediment samples and simulated particles. As a result of the experiment, it was found that the apex size of the cyclone greatly affected the cut diameter(d$_{50}$), and high density particles were separated more effectively.y.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.2
• /
• pp.10-21
• /
• 1998

In this paper, we analyze the problems of conventional and previous mehtod on delay test method in IEEE 1149.1. To solve them, we propose two kinds of delay test architectures. One is called ARCH-C, is for combinatonal circuit, and the other is ARCH-S, for clocked sequential circuit. ARCH-C is able to detect delay defect of 0.5 $T_{tck}$ or 1 $T_{tck}$ size. And ARCH-C have a fixed and small amount of hardware overhead, on the contrary preious method has a hardware overhead on the dependent of CUT. This paper discusses weveral problems of Delay test on IEEE 1149.1 for clocked sequential circuit. We suggest the method called ARCH-S, is based on a clock counting technique to generate continuous clocked input of CUT. the simulation results ascertain the accurate operation and effectiveness of the proposed architectures.res.

• International Journal of Precision Engineering and Manufacturing
• /
• v.3 no.3
• /
• pp.56-61
• /
• 2002

CuFe$_2$O$_4$ ferrite was machined with cermet tools to clarify the machinability. The tool wear became the smallest at the cutting speed of 90m/min with the depth of cut of 0.2mm. The surface roughness became larger with increasing the cutting speed and the chamfer angle of tool. The tool with the chamfer angle of 15° showed the smallest wear. The surface roughness increased almost proportionally with the increase of chip size. The tool wear reduced with increasing feed in the depth of cut not more than 0.2mm.

• The Korean Journal of Applied Statistics
• /
• v.17 no.3
• /
• pp.393-402
• /
• 2004

We suggest a summary of sample design for the statistical survey of E-commerce to estimate the general trend as well as the market size and investment scale of e-commerce based on the Census on Basic Characteristic of Establishments(CBCE). The sample design of this survey is composed of systematic sampling and modified cut-off method.

• Journal of the Korean Society of Industry Convergence
• /
• v.8 no.1
• /
• pp.25-29
• /
• 2005

Titanium specially has high specific strength, excellent mechanical properties as fatigue strength and fracture ductility, good corrosion resistance, and therefore are broadly applied to the various fields. It is required the developmennt for the skills of wire-cut electrical discharge machining(WEDM), but the WEDMed surface was found to be worst due to the attached components of wire. Therefore precision maching method like lapping is necessary for getting high quilty surface. Roughness of lapped surface, surface hardness to each process depth and improved method of surface shape were stuided experimentally, by changing of grain size of diamond lap material and lapping pressure with constant speed in lapping process.