• Transactions on Electrical and Electronic Materials
• /
• v.17 no.3
• /
• pp.178-181
• /
• 2016

In this study a coating experiment was performed to fabricate blue light cut films, which represent a 390~430 nm cut off rate of more than 40% and a transmittance rate of more than 90%, using a roll-to-roll nano micro coating system. The study also analyzed the characteristics of the blue light cut films. Thus, the hardness, which is more than 3H, is ensured through fabricating films using a Sol-Gel process that will determine the proper hardness level. Also, the experiment shows excellent results by cutting blue light through a mixing blue light powder.

• Proceedings of the KIPE Conference
• /
• 2011.11a
• /
• pp.231-232
• /
• 2011

It is very important thing to efficiently utilize the solar power. The conventional solar power system has no energy storage device. So the conventional system cannot cut the peak load. In this paper, the solar power system with the energy storage device and the operation algorithm of peak cut function was proposed to cut the peak load. The algorithm principle is proposed based on the insolation curve and load curve. The simulation and experiment was performed to demonstrate the validity of the peak cut algorithm.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.03b
• /
• pp.427-434
• /
• 2000

When a large number of hazardous road cut-slopes are spreaded in widely scattered areas, the effective investigation and evaluation method that is able to decide the risk of hazardous road cut-slopes, is required. Many different evaluation techniques were suggested by many different researchers based on their demands, but there are the limited researches on the experimental evaluation technique which can be utilized by personnel who does not have much experiences on the road cut-slopes. In this study, the appropriate and effective evaluation method of the dangerous slope is suggested and this method can be used by both inexperienced and experienced persons. Therefore, this is the one of the effective ways that can mitigate the possibility of landslides.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.5
• /
• pp.63-69
• /
• 1999

In tis study the effects of the maximum grit depth of cut on the grinding characteristics were investigated. They are AE signals produced during grinding processes have been studied to find out the appropriate AE parameters for assessing grinding processes. SM45C steel has been ground under the conditions yielding removal rate of workpiece 100, 200,300, and 400m{{{{ {m }^{3 } }}}}/min which was achieved by altering workpiece velocity(v) and apparent depth of cut(Z). According to the experimental result the value of surface roughness increases but grinding power energy rate of AE signal(AErmas2) and specific grinding energy consumed decrease as increasing the maximum grit depth of cut.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.693-698
• /
• 2008

For designing intensity modulation type optical microphone, the irradiance distribution which can be applied to inclined-cut geometrical configuration is suggested. The model is important in analysis of response characteristics f3r intensity modulation type optical microphone. To overcome low sensitivity problem in intensity modulation type optical microphone, inclined-cut optical fiber is considered here. Based on optical geometry, the inclined-cut optical fiber sensor is designed and fabricated. The experiments are carried out to evaluate sensor performance.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.2
• /
• pp.118-125
• /
• 2009

This paper reports the size classification of nanoparticles as well as electrical tuning techniques for the cut-off diameter and collection efficiency. Classifying particles < 100 nm in diameter is quite a technical challenge using a virtual impactor with the cut-off diameter being determined geometrically. However, the proposed virtual impactor can classify particles <100 nm and tune the cut-off diameter by electrically accelerating the particles. The cut-off diameter of the proposed device was tuned from 15 to 50nm.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.40 no.3
• /
• pp.23-38
• /
• 2015

In this paper, we evaluate the strength of three families of cutting planes for a lot-sizing problem. Lot-sizing problem is very basic MIP model for production planning and many strong valid inequalities have been developed for a variety of relaxations in the literature. To use three families of cutting planes in Branch-and-Cut framework, we develop separation algorithms for each cut and implement them in CPLEX. Then, we perform computational study to compare the effectiveness of three cuts for randomly generated instances of the lot-sizing problem.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.1
• /
• pp.29-33
• /
• 2014

Recently, Difficult-to-cut materials are used in many manufacturing industry. But the difficult-to-cut materials are difficult-to-cutting process. So difficult to cut material cutting process was used after heat treatment through preheating for easy cutting process. In this study, Inconel 625 was preheating using laser heat source in computer simulation. Laser heat source temperature applied $1290^{\circ}C$ that suitable preheating temperature for Inconel 625. And temperature effects such as temperature distribution for moving heat source studied apply to similar actual process condition. Simulation results for heat treatment effects through temperature distribution verified.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.4 no.2
• /
• pp.26-35
• /
• 2001

We are, now in the 21st century, that environmental preservation and the campaign for bio-diversity protection are very important issues the government must deal with as nation's main policy. To make road and building construction, housing land service, construction of golf fields, and various development works, we have made artificial topographical alterations and as a result, the cut-slop has been increased. However, without the proper study and clear planning, revegetation for the stability of the cut-slop has worked out. These efforts now are causing derangement of an ecosystem and spoiling the nature without considering for ecological adaptation. Therefore, we are going to find out the Revegetation Method to Cut-Slopes considering both the ecological adaptation and harmony with the nature.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.25 no.3
• /
• pp.1-15
• /
• 2000

In this paper, we propose a practical cut generation method based on the Chvatal-Gomory procedure for the (0, 1)-Knapsack problem with a variable capacity. For a given set N of n items each of which has a positive integral weight and a facility of positive integral capacity, a feasible solution of the problem is defined as a subset S of N along with the number of facilities that can satisfy the sum of weights of all the items in S. We first derive a class of valid inequalities for the problem using Chvatal-Gomory procedure, then analyze the associated separation problem. Based on the results, we develop an affective cut generation method. We then analyze the theoretical strength of the inequalities which can be generated by the proposed cut generation method. Preliminary computational results are also presented which show the effectiveness of the proposed cut generation method.