• 한국안전학회지
• /
• 제32권4호
• /
• pp.28-33
• /
• 2017

A sharp curved ballasted track on earthwork that was connected with a direct fixation slab track on steel box railway bridges have been deformed and damaged despite the frequently maintenance by a restoring force of sharp curved rail and track-bridge interaction forces such as axial forces and longitudinal displacement of continuous welded rail(CWR) owing to their structural characteristics, calling for alternatives to improve the structural safety and track irregularity. In this study, the authors aim to prove a cause of deformation for the sharp curved ballasted tracks to enhance the structural safety and track irregularity of ballasted track in service. A track-bridge interaction analysis and a finite-element method analysis for the sharp curved ballasted track were performed to consider the axial force and longitudinal displacement of CWR, the temperature and the effect of restoring force of sharp curved rail. From the results, the deformation of the sharp curved ballasted track with adjusted sleeper spacing from 833mm to 590mm were significantly reduced.

• International Journal of Railway
• /
• 제7권2호
• /
• pp.57-63
• /
• 2014

This paper presents the optimization of suspension characteristics under the condition of curved track railway vehicles. Reducing lateral acceleration on curved track is an issue for high-speed railway vehicles. In terms of curved track running environments, reducing the lateral vibration of railway vehicles is critical to safety and curving performance. The properties of lateral damping and stiffness of both primary and secondary suspension show effect on wheel-set, bogie and car-body. Analysis for reducing the lateral vibration of rail vehicles with respect to the characteristics of both primary and secondary suspension has been developed using ADAMS/Rail. Response Surface Method has been chosen for the purpose of verifying correlation effects among design parameters. Also, this paper suggests the method for designing optimal suspension of railway vehicles on curved track. The optimization result indicates decrement of lateral acceleration on wheel-set by 3% and bogie by 1% on curved track. Finally, this paper comes to the conclusion that suspension system of railway vehicle (KTX I) is properly designed when regarding lateral vibration of railway vehicle on diverse curved track condition.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.426-436
• /
• 2006

The use of the CWR track has increased consistently in the worldwide. Because the use of CWR track not only reduces the track maintenance cost, noise and vibration, but increases the life cycle of track components. Therefore, to increase train speed, improve riding condition and secure running stability, the necessity of study on making CWR is increasing. This study includes the development of a thermal buckling theory in the evaluation of curved track stability. The lateral stability of curved CWR is studied for track buckling prevention through the parameter studies. It studied the lateral buckling of the curved CWR track on the 3-D nonlinear analysis. The parameters include rail size, cant, track curvature.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 추계학술대회 논문집
• /
• pp.823-829
• /
• 2005

The extent of slack is correlative with the wheelbase of vehicle as well as the distance between the inner faces of flanges. Since the movable clearance of wheel flange is getting reduced in curved track, the vehicle is more difficult to negotiate the track. By this reason, a certain extent of slack is normally designed for curved track to allow the movable clearance corresponding to that of straight track. In case of some foreign railways,. the fixed extent of slack has been classified by the ranges of curve radius. In case of KNR, the slack is calculated by a formula for each case of curve radius and it therefore seems quite precise method. However, since there is a wide range of slack adjustment $(S'=0\~15mm)$ in calculation formula itself, too excessive or too little slack can be calculated. This study is to approach the technical review on slack calculation and to offer the reasonable slack design through the full-scale experiment at sharp curved track without slack.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2001년도 춘계학술대회 논문집
• /
• pp.289-294
• /
• 2001

A curved track needs balanced super elevation according to the speed of the passing train and it is limited by maximum allowable amount. Therefore, passing speed at high degree curved track has to be controlled below the limits. Accurate position of the Speed Limit Post(SLP), which shows allowable speed of curved track dose not regulated so design and line side maintenance engineer adopt the position differently, When the rate of cant deficiency is considered on transition-curved section, the SLP should be located at the beginning point of the transition curve so as to control the speed of passing train and it will increase ride quality to passenger.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.2163-2173
• /
• 2011

In this study, the deformations and stresses occurred in the elastic rail fastening system were evaluated according to applied extreme track forces based on various field conditions, track curvature and poor properties. The purpose of this study is to establish a method for efficient management and suggest guide line for track construction in order to secure the performance quality of the elastic rail fastening system on the sharp curved track.. Therefore, initial construction qualities of rail and concrete bed, initial clamping force and applied extreme track forces were used into experiment as several parameters. Using these test results, the performance characteristics of the elastic rail fastening system were also evaluated. As a result, it suggested the method to secure long-term durability of fastening system and comparing sharp curved track to results on field test.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 추계학술대회 논문집
• /
• pp.382-388
• /
• 2005

SMSC(Seoul Metropolitan Subway Corporation) is substantially taking the core role of mass transit system in Seoul Metropolitan area. When it was built, the design had challenged to sharp curved tracks less than 250m radius considering the protection of buildings and cultural properties as well as the connection to ground roads. Such circumstances have required a certain extent of slack in track geometry and therefore led to the construction of ballasted track with wooden sleepers. However, the dynamic force from running on sharp curved track has caused the misalignment and abnormal failure of track geometry, and it has resulted in a frequent maintenance and repair works which require a lot of cost and manpower. In this paper, we present the construction case of maintenance-free track system by using of concrete sleeper and elastic rail fastening system to ensure the safety of both passengers and trains, and to contribute the effective maintenance for track facilities of SMSC.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.948-954
• /
• 2004

이 연구의 목적은 호남선과 경부선의 기존선 전철화 선로의 곡선부에서 G7 개발차량과 KTX 차량의 속도를 증가해서 주행했을 경우 궤도구조의 성능평가와 주행안전성를 측정 분석한 것이다. 구조안전성과 주행안정성 평가를 위해서 측정기준으로 정립하였으며 계측망도를 구성하여 현장 계측을 수행하였다. 윤중, 횡압과 레일수직, 수평변위, 침목수직변위, 레일응력을 측정하였으며 이 결과를 토대로 궤도구조의 부담력과 열차 주행안정성을 평가하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1998년도 창립기념 춘계학술대회 논문집
• /
• pp.510-516
• /
• 1998

Dynamic stability of a high speed train is very important. This paper presents a dynamic stability analysis of K-TGV using Vampire Program. The analysis of stability on this paper is performed in condition of track irregularity, curved track and strong gust. The critical speed of K-TGV is 140m1s, and it is stable when runs on 7000R(cant 150mm) curved track and on linear track with the body exerted 101kN lateral impulse force.

• 한국철도학회논문집
• /
• 제8권6호
• /
• pp.550-558
• /
• 2005

The track performance evaluation in curves of conventional line subjected to loading condition caused by tilting trains was carried out. And the correlations between train speed and track alignment was reviewed. The parameters of track alignment were determined by field investigation of all curves in conventional line. It was founded that the pressure of the rail did exceed the allowable stress when the tilting train speed was over 96km/hr in radius of 300m. As the radius of curvature is smaller, applied force on the track becomes larger in the curved track without regard to laying of the continuos welded rail. On the while, the change of applied force on the track corresponding to the change of the cant is not so large.