• Preventive Nutrition and Food Science
• /
• v.6 no.1
• /
• pp.23-28
• /
• 2001

A study was carried out to establish a detection method of irradiated shellfish through thermoluminescence (TL). The TL intensity of first glow curves for irradiated bloody, freshwater, and short-neck shellfish increased from control until 5 kGy and increased slightly room 5 kGy until 10 kGy. Maximum TL temperatures of all irradiated samples tested were below 23$0^{\circ}C$, within temperature interval of 150~25$0^{\circ}C$ recommended for evaluation. Since just in control, glow curve ratios of G3 and G4 calculated from re-irradiated (1 kGy) bloody, freshwater and shortneck were over 0.5, detection in control was possible. However, as glow curve ratios after three months were below 0.5, detection by glow curve ratios after three months was impossible. Gl, which calculated from unirradiated samples, exhibited below 0.1, they were classified as unirradiated. In all samples, all the irradiated shellfish could be classified correctly as irradiated by hemaximum TL temperatures and shape of the second glow curve because those were shown in a lower temperature region than those of the first glow curve.

• Journal of the Korean Society of Physical Medicine
• /
• v.11 no.2
• /
• pp.13-16
• /
• 2016

PURPOSE: The Fukuda test can be used at home and in school to diagnose scoliosis at an early stage and prevent serious curvature of the spine. This study aimed to use the Fukuda test to detect scoliosis. An additional aim was to invoke the national interest in imbalanced postures and habits, which result in scoliosis, by providing data obtained in periodic assessments. METHODS: The study consisted of 35 idiopathic scoliosis patients (22 in right lumbar spinal region and 13 in the left lumbar spinal region). The distance of displacement and angle of displacement were measured following the Fukuda test. A correlation analysis was then used to examine the distance of displacement and angles of displacement and rotation with regard to the direction of the curve in scoliosis. RESULTS: There was a significant negative correlation (p<0.00) between the direction of the curve in scoliosis and the angle of displacement, but there was no correlation between the cobb's angle and distance of displacement or between the cobb's angle and angle of rotation. CONCLUSION: The Fukuda test did not capture changes in spinal curvature such as the cobb's angle, or subsequent changes in the muscles. Thus, the Fukuda test is not suited to examining the direction or status of the thoracic curve in scoliosis patients. Simple methods to objectively measure scoliosis need to be developed.

• The Transactions of the Korea Information Processing Society
• /
• v.6 no.12
• /
• pp.3710-3717
• /
• 1999

For the development of unmanned autonomous vehicle, it is essential to detect obstacles, especially vehicles, in the forward direction of navigation. In order to reliably exclude regions that do not contain obstacles and save a considerable amount of computational effort, it is often necessary to confine computation only to ROI(region of interest)s. A ROI is usually chosen as the interior region of the lane. We propose a computationally simple and efficient method for the detection of lanes based on Hough transform and quadratic curve fitting. The proposed method first employs Hough transform to get approximate locations of lanes, and then applies quadratic curve fitting to the locations computed by Hough transform. We have experimented the proposed method on real outdoor road scene. Experimental results show that our method gives accurate detection of straight and curve lanes, and is computationally very efficient.

• Journal of applied mathematics & informatics
• /
• v.17 no.1_2_3
• /
• pp.39-48
• /
• 2005

A convex region covers a family of curves if it contains a congruent copy of each curve in the family, and a 'worm problem' for that family is to find the convex region of smallest area. In this paper, we find the smallest triangular cover of any prescribed shape for the family S of all triangles of diameter 1.

• Journal of KIISE
• /
• v.44 no.11
• /
• pp.1194-1208
• /
• 2017

A traditional average smoothing method is designed for smoothing out noise, which, however, unintentionally results in smooth corner points on the curvature accompanied with a shrinkage of curves. In this paper, we propose a novel curve smoothing method via polygonal approximation of the input curve. The proposed method determines the smoothing weight for each point of the input curve based on the angle and approximation error between the approximated polygon and the input curve. The weight constrains a displacement of the point after smoothing not to significantly exceed the average noise error of the region. In the experiment, we observed that the resulting smoothed curve is close to the original curve since the point moves toward the average position of the noise after smoothing. As an application to digital cartography, for the same amount of smoothing, the proposed method yields a less area reduction even on small curve segments than the existing smoothing methods.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.10
• /
• pp.1567-1574
• /
• 2001

In order to operate an RPV safely it is necessary to keep the pressure-temperature (P-T) limit during the heatup and cooldown process. While the ASME Code provides the P-T limit curve for safe operation, this limit curve has been prepared under conservative assumptions In this paper the effects of conservative assumptions involved in the P-T limit curve specified in the ASME Code Sec. XI were investigated. Three different parameters the crack depth the cladding thickness and the cooling rate, were reviewed based on 3-D finite element analyses. Also the constraint effect on P-T limit curve generation was investigated based on J- T approach. It was shown that the crack depth and the constraint effect change the safe region in P-T limit curve significantly Therefore it is recommended to prepare a more precise P-T limit curve based on finite element analysis to obtain P-T limit for safe operation of an RPV.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.341-348
• /
• 2017

This study examined the effects of the location and direction of the scolioti curve on postural balance in patients with idiopathic scoliosis. Fifteen subjects were divided into three groups: right thoracic curve group, left lumbar curve group, and double curve group. The dynamic trunk motion (angle variation in the lumbar, thoracolumbar, lower thoracic and upper thoracic region) and plantar pressure distribution (maximum force and peak pressure) were assessed using an ultrasound-based motion analysis system and Emed-at platform system. From the results, it was confirmed that patients with idiopathic scoliosis showed postural imbalance with an increased angle and pressure asymmetry according to the location and direction of the scoliotic curve for dynamic trunk motion and plantar pressure distribution. In addition, there were differences in the postural balance pattern between the single curve and double curve groups. Further studies for developing a rehabilitation training device will be conducted to improve the postural control ability and trunk balance as well as treat scoliosis based on the results of this study.

• Journal of Magnetics
• /
• v.20 no.3
• /
• pp.258-264
• /
• 2015

In this paper, an adequate B-H curve extrapolation method is proposed and its reliability is verified through experiments. A method is developed to estimate the magnetic saturation induction from the density of the lamination core and electrical resistivity. The magnetic saturation induction of electrical steels measured using a vibration sample magnetometer are compared with the analytical results to validate the accuracy of the proposed estimation method. It is found that the predicted error in the magnetic saturation induction of the electrical steels are approximately 1.2% when the proposed method is used. The performance of interior permanent magnet synchronous motors that applies the proposed method are evaluated via 2D nonlinear finite element analysis and through experiments. Based on the obtained results, the extrapolated B-H curves from the estimated saturation induction can be used for various analyses in saturation region.

• Journal of the Korean Mathematical Society
• /
• v.58 no.6
• /
• pp.1407-1419
• /
• 2021

The Iwasawa decomposition NAK of the Lie group G = SO₀(2, 1) with a left invariant metric produces Riemannian submersions G → N\G, G → A\G, G → K\G, and G → NA\G. For each of these, we calculate the curvature of the base space and the lifting of a simple closed curve to the total space G. Especially in the first case, the base space has a constant curvature 0; the holonomy displacement along a (null-homotopic) simple closed curve in the base space is determined only by the Euclidean area of the region surrounded by the curve.

• Journal of the korean Society of Automotive Engineers
• /
• v.8 no.1
• /
• pp.40-51
• /
• 1986

A study has been made of the corrosion fatigue of high strength low alloy steel in 3.5% NaCl solution under tension stress for solution temperature being 25.deg. C, 55.deg. C and 85 .deg. C. The main results obtained are as follows; 1) The corrosion fatigue crack growth rate curve could be divided into the First Region, the Second Region and the Third Region. 2) The corrosion fatigue crack growth rates in the First Region and the Second Region were Arrhenius temperature-dependent in this test range. The apparent activation energies for the corrosion fatigue cack growth rate were found to be 2000cal/mol in the First Region and 3700 cal/mol in the Second Region. 3) Hematite (Fe$_{2}$O$_{3}$) as the hexahedral crystal and magnetite (Fe$_{3}$O$_{4}$) as the octahedral crystal were observed in the corrosion products on the corrosion fatigue fracture surface at 85.deg. C and the anode fusion seem to be generated in the crack tip region at high temperature. 4) The complex environment effect ratio which was defined by the ratio of fatigue crack growth rate in corrosion environment to that in air might be considered not only a criterion estimating the effect of environment quantitatively but also an important parameter in the selection of the design stress for the fail safe design. The complex environment effect was not greater than ten in this test.