• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 추계학술대회 논문집
• /
• pp.742-747
• /
• 2005

Electric railroad transformer of a supply of Operation power of DC electric cars is intense fluctuation of load and flows the only big short-circuit current as a accident of the power system. it is a peculiarity more severe than general power transformer. Consequently, researches the properties about the rectifier mold transformer of DC substation and applies with data of safety of the electric railroad transformer. This paper analyzed a failure mode, the accident occurrence scenario and the be latent dangerous unit against the rectifier mold transformer of DC railway system.

• Journal of Power Electronics
• /
• 제16권1호
• /
• pp.93-101
• /
• 2016

A new four-primary-switch diode clamped soft switching three-level DC-DC converter (TLDC) with full zero-voltage switching (ZVS) load range and TL secondary voltage waveform is proposed. The operation principle and characteristics of the presented converter are discussed, and experimental results are consistent with theoretical predictions. The improvements of the proposed converter include a simple and compact primary structure, TL secondary rectified voltage waveform, wide load range ZVS for all primary switches, and full output-regulated range with soft switching operation. The proposed converter also has some disadvantages. The VA rating of the transformer is slightly larger than that of conventional TLDCs in variable input and constant output mode. The conduction loss of the primary coil is slightly higher because an air gap is inserted into the magnetic cores of the transformer. Finally, the secondary circuit is slightly complex.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2007년도 하계학술대회 논문집
• /
• pp.29-31
• /
• 2007

This is experimental result which is reported with use the dsPIC30F2020 16-Bit SMPS microprocessor of MicroChip company which composes a digital control circuit and it applies in switched-mode power supply unit. The basic topology consist of the synchronous rectifier in a two transistor forward converter. In a experiment, it is used from microprocessor to do with A/D conversion and it is embodied with PID controls in order to detect a over-current, over-voltage, over-temperature and output voltage.

• Transactions on Electrical and Electronic Materials
• /
• 제5권1호
• /
• pp.7-10
• /
• 2004

A new method for fabrication of transistor like structure of the bifacial solar cell using spin-on doping and electroless plating has been proposed and the basic characteristics of the bifacial cell have been investigated. It is found that 9％ increase in short circuit current is achieved with bifacial connection than the unifacial connection. Some unwanted effect of the series resistance on collection efficiency under different mode of illumination has been pointed out. Loss mechanisms inherent in the transistor like bifacial structure have also been discussed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.1078-1080
• /
• 2003

This paper proposes the boost input type resonant power supply for driving the magnetron device of the high-capacity microwave oven. Circuit topology of the proposed power supply is the boost input type resonant converter which uses the resonance between transformer leakage inductance and resonance capacitance. Proposed power supply obtains high power factor more than 98% through continuous current mode pulse width modulation. To verify the validity of the proposed power supply, operation principle in the steady state is analyzed and experimental results are presented.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.1244-1246
• /
• 2003

Conventional Switched Mode Power Supplies(SMPS) with diode-capacitor rectifier have distorted input current waveform with high harmonic content. Typically, these SMPS have a power factor lower than 0.65. To improve with this problem. the power factor correction(PFC) circuit of power supplies has to be introduced. Specially, to reduce size and manufacture cost of power conversion device, the single-stage PFC converter is increased to demand as necessary of study. In this case single-stage PFC converter has been used DC-DC converter with boost converter. However in this paper, it is studied flyback converter of high power factor, high efficiency by feedforward control. Also, the validity of designed and manufactured high power factor flyback converter is confirmed by simulation and experimental results.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제15권2호
• /
• pp.184-193
• /
• 2015

This paper proposes a cost-efficient and automatic method for large data acquisition from a test chip without expensive equipment to characterize random process variation in an integrated circuit. Our method requires only a test chip, a personal computer, a cheap digital-to-analog converter, a controller and multimeters, and thus large volume measurement can be performed on an office desk at low cost. To demonstrate the proposed method, we designed a test chip with a current model logic driver and an array of 128 current mirrors that mimic the random process variation of the driver's tail current mirror. Using our method, we characterized the random process variation of the driver's voltage due to the random process variation on the driver's tail current mirror from large volume measurement data. The statistical characteristics of the driver's output voltage calculated from the measured data are compared with Monte Carlo simulation. The difference between the measured and the simulated averages and standard deviations are less than 20% showing that we can easily characterize the random process variation at low cost by using our cost-efficient automatic large data acquisition method.

• 한국산업정보학회논문지
• /
• 제21권1호
• /
• pp.17-25
• /
• 2016

본 논문은 동기회로에서 누설 전류를 줄이기 위해서 사용되는 파워 스위치 구조를 결합한 새로운 구조의 저전력 비동기 회로 설계 방법을 제안하고자 한다. Static 방식, Semi-static 방식과 같은 기존의 지연 무관방식의 비동기 방식과 비교해서 다소 속도의 손해는 있지만, 파워 스위치에 의해서 데이터가 없는 상태에서는 누설 전력을 줄일 수 있고, 전체 사이즈가 작아짐으로써 데이터가 입력되는 순간의 스위칭 전력도 줄일 수 있는 장점이 있다. 따라서, 제안된 방법은 속도보다 저전력을 기본으로 하는 사물인터넷 시스템에서 요구되는 전전력 설계 방법이 될 것이다. 본 논문에서는 새로운 방식의 비동기 회로를 사용하여 $4{\times}4$곱셈기를 0.11um 공정으로 설계하고, 기존의 비동기 방식의 곱셈기와 스피드, 누설 전류, 스위칭 파워, 회로 크기 등을 비교하였다.

• 대한전자공학회논문지SD
• /
• 제45권1호
• /
• pp.56-63
• /
• 2008

본 논문에서는 WCDMA 통신용 송신기에 적용 가능한 12비트 1GS/s 전류구동 방식의 혼합형 DAC를 설계하였다. 제안된 DAC는 혼합형 구조로써 하위 4비트는 이진 가중치 구조, 중간비트와 상위비트는 4비트 온도계 디코더 구조로 12비트를 구성하였다. 제안된 DAC는 혼합형 구조에서 발생되는 지연시간에 따른 성능 저하를 개선하기 위해 지연시간보정 회로를 사용하였다. 지연시간보정 회로는 위상주파수 검출기, 전하펌프, 제어회로로 구성되어 이진 가중치 구조와 온도계 디코더 구조에서 발생하는 지연시간을 감소시킨다. 제안한 DAC는 CMOS $0.18{\mu}m$ 1-poly 6-metal n-well 공정을 사용하여 제작되었고 측정된 INL/DNL은 ${\pm}0.93LS/$ 0.62LSB 이하로 나타났다. 입력 주파수 1MHz에서 SFDR은 약 60dB로 측정되었고 SNDR은 51dB로 측정되었다. 단일 DAC의 전력소모는 46.2mW로 나타났다.

• 전기전자학회논문지
• /
• 제16권4호
• /
• pp.335-342
• /
• 2012

본 논문에서는 고효율과 고역률을 위한 새로운 DCM-ZVS 스텝 업-다운 AC-DC 컨버터에 대해 연구된다. 제안한 DCM-ZVS 컨버터에 사용된 스위칭 소자들은 새로운 유사공진 회로에 의해 소프트 스위칭 기법으로 동작되고, 펄스폭변조(PWM) 방식에 의한 전류불연속모드(DCM)로 구동된다. 제안한 컨버터의 유사공진 회로는 스텝 업-다운 인덕터와 무손실 스너버 커패시터로 구성되고, 또한 DCM에 의해 제어회로 기법과 제어회로 구성이 간단한 장점이 주어진다. 입력 교류 전류파형은 일정 스위칭 주파수에 의한 교류 입력전압의 크기에 비례한 유사 정현파형으로 된다. 그 결과, 제안한 DCM-ZVS 컨버터는 낮은 스위칭 손실과 고효율을 얻을 수 있으며, 컨버터의 입력역률은 거의 단위역률로 된다. 해석적 결과의 타당성은 다양한 컴퓨터 시뮬레이션과 실험 결과를 통해 입증된다.