• Journal of IKEEE
• /
• v.18 no.4
• /
• pp.586-592
• /
• 2014

In this paper, high efficiency power management IC(PMIC) with DT-CMOS(Dynamic threshold voltage Complementary MOSFET) switching device is presented. PMIC is controlled PWM control method in order to have high power efficiency at high current level. The DT-CMOS switch with low on-resistance is designed to decrease conduction loss. The control parts in Buck converter, that is, PWM control circuit consist of a saw-tooth generator, a band-gap reference(BGR) circuit, an error amplifier, comparator circuit, compensation circuit, and control block. The saw-tooth generator is made to have 1.2MHz oscillation frequency and full range of output swing from supply voltage(3.3V) to ground. The comparator is designed with two stage OP amplifier. And the error amplifier has 70dB DC gain and $64^{\circ}$ phase margin. DC-DC converter, based on current mode PWM control circuits and low on-resistance switching device, achieved the high efficiency nearly 96% at 100mA output current. And Buck converter is designed along LDO in standby mode which fewer than 1mA for high efficiency. Also, this paper proposes two protection circuit in order to ensure the reliability.

• Journal of Power Electronics
• /
• v.10 no.5
• /
• pp.485-490
• /
• 2010

Sensorless control methods are generally used in motor control for home-appliances because of the material cost and manufactureing standard restrictions. The current model-based control algorithm is mainly used for PMSM sensorless control in the home-appliance industry. In this control method, the rotor position is estimated by using the d-axis and q-axis current errors between the real system and a motor model of the position estimator. As a result, the accuracy of the motor model parameters are critical in this control method. A mismatch of the PMSM parameters affects the speed and torque in low speed, steadystate responses. Rotor position errors are mainly caused by a mismatch of the stator resistance. In this paper, a stator resistance compensation algorithm is proposed to improve sensorless control performance. This algorithm is easy to implement and does not require a modification of the motor model or any special interruptions of the controller. The effectiveness of the proposed algorithm is verified through experimental results.

• Proceedings of the KIPE Conference
• /
• 2017.11a
• /
• pp.31-32
• /
• 2017

모듈형 멀티레벨 컨버터(Modular Multilevel Converter, MMC) 토플로지는 HVDC 송전을 위한 전력변환 시스템 또는 전기추진 선박과 같은 대용량 시스템에 주로 사용된다. 본 논문은 MMC 시스템의 출력 전류 센서에서 전류 검출 과정 시, 발생 가능한 오차 성분의 영향을 분석하였다. 또한 전류 센서의 오차 성분을 일반화 하고, 이를 시뮬레이션을 통해 타당성을 검증하였다.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.586-588
• /
• 2008

농형 유도전동기의 센서리스 벡터제어시 기존의 약계자 알고리즘은 오토튜닝 오차에 의해 자속기준값이 크게 계산되어질 때 역기전력과, 전압제한값에 의해 최대전류를 출력할 수 없다. 본 논문에서는 약계자 영역에서 토크분 전류제어 오차를 이용하여 자속 기준값을 보상함으로써 전류부족에 의한 속도강하를 방지하는 알고리즘을 소개하였고, 시뮬레이션을 통해 그 타당성을 검증하였다.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.1993-1995
• /
• 1998

The compensation problem of error and various problems due to delay of speed sensor itself and speed detection have issued in case using speed sensor in the adjustable speed control of induction motor. This paper have applied the stator flux oriented vector control algorithm and space voltage vector PWM method in order to improve an dynamic character of voltage-source inverter system, and also used the better IP controller in the speed response than Pl controller as speed controller. This paper estimated the rotator speed using input current of inductor motor and flux component invoked through voltage drop by terminal voltage and stator resistor.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.227-229
• /
• 2005

교류전동기의 벡터제어 구동 시스템에서 상전류 측정 오차는 토크 및 속도 제어 성능에 직접적인 영향을 주는 요소로서, 맥동 없는 토크 및 속도 제어를 위해서는 상전류의 정확한 측정이 필요하다. 상전류 측정 오차는 오프셋(Offset) 변동에 의한 오차와 스케일(Scale) 차이에 의한 오차로 분류할 수 있으며, 각각의 오차 성분은 고정자 전기 주파수의 1배 및 2배에 해당하는 토크 맥동을 야기 한다. 본 논문에서는 교류전동기 벡터제어 구동 시스템에서 상전류 측정 오차에 의한 토크 맥동을 저감시킬 수 있는 새로운 알고리즘을 제시하며, 시뮬레이션 및 실험을 통해 제안된 방식의 타당성을 입증한다.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.293-295
• /
• 2007

This paper proposes a control algorithm for the power supply to maintain the desired output voltage waveform when the instantaneous power failure occurs. The proposed system switches the control mode between the voltage-controlled and the current-controlled modes in the instantaneous power failure. The proposed control method has little steady-state error and good transient response. The validity of the proposed scheme is investigated through simulation and experimental results.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.477-478
• /
• 2015

2상 유도전동기용 벡터제어 인버터에서는 전류센서를 사용하여 a상 및 b상의 전류를 측정해야 한다. 그러나, 이 전류값을 마이크로컨트롤러의 A/D컨버터로 읽어 들이는 과정에서 전류 센서와 증폭회로로부터 발생하는 오프셋 오차와 변환이득 오차를 포함할 수 있다. 2상 유도전동기의 벡터제어 시스템이 이러한 오차들을 포함한다면 전동기의 출력토크에 리플이 발생한다. 본 논문에서는 이러한 전류측정 오차를 실시간으로 보상하여 전동기의 토크리플을 제거하는 방법을 제안하였으며, 이러한 방식을 360[W]급의 2상 유도전동기용 벡터제어 인버터에 적용하여 컴퓨터 시뮬레이션과 실험으로 유효성을 확인하였다.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.679-684
• /
• 1989

In this paper, we describe the PTP notion of robot manipulators by neural networks. The PTP motion requires the inverse kinematic redline and the joint trajectory generation algorithm. We use the multi-layered Perceptron neural networks and the Error Back Propagation(EBP) learning rule for inverse kinematic problems. Varying the number of hidden layers and the neurons of each hidden layer, we investigate the performance of the neural networks. Increasing the number of learning sweeps, we also discuss the performance of the neural networks. We propose a method for solving the inverse kinematic problems by adding the error compensation neural networks(ECNN). And, we implement the neural networks proposed by Grossberg et al. for automatic trajectory generation and discuss the problems in detail. Applying the neural networks to the current trajectory generation problems, we can refute the computation time for trajectory generation.

• Journal of Power Electronics
• /
• v.16 no.1
• /
• pp.38-47
• /
• 2016

This paper presents DG based droop controlled parallel inverter systems with virtual impedance considering the unequal resistive-inductive combined line impedance condition. This causes a reactive power sharing error and dynamic performance degradation. Each of these drawbacks can be solved by adding the feedforward term of each line impedance voltage drop or injecting the virtual inductor. However, if the line impedances are high enough because of the long distance between the DG and the PCC or if the capacity of the system is large so that the output current is very large, this leads to a high virtual inductor voltage drop which causes reductions of the output voltage and power. Therefore, the line impedance voltage drops and the virtual inductor and resistor voltage drop compensation methods have been considered to solve these problems. The proposed method has been verified in comparison with the conventional droop method through PSIM simulation and low-scale experimental results.