• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.367-370
• /
• 2000

In this study, thin films of 70/30 and 80/20 mol% P(VDF-TrFE) copolymers were fabricated by physical vapor deposition method. In order to determine the optimum deposition condition, the copolymer thin films were fabricated in the heating temperature of 260$^{\circ}C$, 280$^{\circ}C$, and 300$^{\circ}C$. The deposition rate was measured in a real time by thickness monitor. The surface image of prepared thin films was analyzed by using AFM. From the results of TG-DTA,70/30 and 80/20 mol% P(VDF-TrFE) copolymers were observed the Curie transition point below the melting point. As the results of AFM and FT-IR analysis, we determined that the optimum deposition temperature was 300$^{\circ}C$.

• Journal of the Microelectronics and Packaging Society
• /
• v.13 no.1 s.38
• /
• pp.31-35
• /
• 2006

This paper is studied on a protective control system for electrical fire used electrical characteristics of SCR and multilayer-type PTC thermistor. The PTC thermistor has characteristic or positive resistivity temperature coefficient according to the temperature variation, which is construction of a regular square and cube demarcation with $BaTiO_{3_}$Ceramics of positive temperature coefficient. Also PTC shows the phenomenon which is rapidly increased in the resistivity if the temperature is increased over Curie temperature point. This paper is proposed on a protective control system used multilayer-type PTC which is protected from electrical fire due to electric short circuit faults or overload faults. Some experimental results of the proposed apparatus is confirmed to the validity of the analytical results.

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.1
• /
• pp.51-58
• /
• 2008

This paper is studied on a prevention system for electrical fire and electrical faults by using electrical temperature characteristic of PTC thermistor. The PTC thermistor has characteristic of positive resistivity temperature coefficient according to the temperature variation, which is construction of a regular square and cube demarcation with $BaTiO_3$ ceramics of positive temperature coefficient. Also PTC shows the phenomenon which is rapidly increased in the resistivity if the temperature is increased over Curie temperature point. This paper is proposed on a protective control system used with temperature sensor of PTC thermistor. The proposed prevention system will prevent electrical fires due to electric short circuit faults or overload faults. And the prevention system will solve the problems that circuit breakers to be commonly used at existing are happened frequently electrical fires and electrical disasters due to incapable operation, weak reliability and low speed response. Some experimental results of the proposed apparatus are confirmed to the validity of the analytical results.

• Fire Science and Engineering
• /
• v.21 no.4
• /
• pp.65-71
• /
• 2007

This paper is studied on a protective control system for electrical fire and electrical faults by using electrical and thermal characteristics of PTC thermistor. The PTC thermistor has characteristic or positive resistivity temperature coefficient according to the temperature variation, which is construction of a regular square and cube demarcation with $BaTiO_3$ Ceramics of positive temperature coefficient. Also PTC thermistor shows the phenomenon which is rapidly increased in the resistivity if the temperature is increased over Curie temperature point. This paper is proposed on a protective control system used PTC thermistor which is protected from electrical fire due to electric short circuit faults or overload faults. Some experimental results of the proposed electric safety control apparatus are confirmed to the validity of the analytical results.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.4 no.1
• /
• pp.27-39
• /
• 1967

The fabrication of the barium titanate ceramic capcitors has been studied. The effects of the impurities for alumina and silica upon mechanical and electrical characteristics have been examined in detail. The preparation of equimolar titanium oxide and barium carbide in addition two percent of alumina and point two five perdcent of silica has shown the best results. This is fired up to thirteen hundred degrees Celsius with the rate of two hundred degrees Celsius per hour and soaked three hous at this temperature. The dielectric constant of this sample is approximately equal with the standard and theoretical values at room temperature. The insulation resitances of the most fabricated capacitors are in the order of twenty thousand megohms, the dielectric constant and the dissipation factor are almost flat up to just below of curie temperature, and the porosities of the most ceramics are less than point one percent and well close or equal to zero percent.

• Journal of the Korean Ceramic Society
• /
• v.25 no.4
• /
• pp.321-328
• /
• 1988

The sintering phenomena, electrical resistivity, dielectric and piezoelectric properties of lead titanate ceramics modified by the partial substitution of La for Pb and Mn for Ti, (Pb1-1.5xLax)(Ti1-yMny)O3 ceramics, have been investigated. In (Pb1-1.5xLax)(Ti1-yMny)O3 system, with increasing lanthanum content, the realtive bulk density increased, but the Curie point and tetragonality (c/a) decreased. The tetragonal-to-cubic phase transition boundary existed in the range of 0.20

• Journal of Korean Society for Atmospheric Environment
• /
• v.3 no.2
• /
• pp.39-45
• /
• 1987

Rubber particles emitted from automobile tire tread by abrasion were collected by Andersen sampler with atmospheric dusts. The samples of atmospheric dusts at each stage were analysed for rubber particles by Curie point pyrolysis-gas chromatography with Apiezon grease L column. Pyrolysis was done at 740$^circ$C for 5 seconds. In the pyrogram, NR rubber (bus and truck tire tread) was determined by isoprene peak, and SBR rubber (passenger car tire tread) was determined by styrene peak simultaneously. The size distribution of rubber particles was proportioned with the size of rubber particles. The concentrations of NR and SBR rubber were 0.23 $\mug/m^3$ and 1.31 $\mug/m^3$, respectively, in the atmospheric dusts which were collected from the street in front of Yonsei University on April 1986. The ratio of tire tread rubber in the atmospheric dusts was about 0.63%.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.3
• /
• pp.301-308
• /
• 1996

Domain structure and properties of LiNbO3 single crystals grown by continuous method (Orr's method) were characterized. It was found that the growth striation of the grown crystals correspond with domain structure and the positive-negative domains were repeated with the perpendicular direction to the C axes. The formation of negative domains were related to the rapid crystal growth rate. The measured dielectric constant of the grown crystal was 140∼150 at 100 kHz at the room temperature and Curie point was 1153℃.

• Journal of the Korean Ceramic Society
• /
• v.34 no.5
• /
• pp.461-466
• /
• 1997

Dielectric and piezoelectric properties of (Pb1-1.5xLnx)(Ti0.98Mn0.02)O3 ceramics with x=0~0.2 have been investigated. Pb(Ti0.98Mn0.02)O3 showed poor sinterability and cracking on cooling, but the substitution of Nd3+ ions into Pb2+ sites resulted in dense microstructures without cracking through reducing crystallographic anisotropy. The Nd3+ substitution, however, deteriorated the temperature stability of the piezoelectric properties because of lowering the Curie point. Electromechanical anisotropy(Kt/Kp) indicated a maximum value of 10 when x=0.1. This result might be attributed to the counteracting effects that with increasing x, the lattice anisotropy decreases while the poling becomes easier due to the increase in O2- vacancy concentration. Thickness-shear mode resonators with (Pb0.85Nd0.1)(Ti0.98Mn0.02)O3 composition showed good resonant characteristics around 4.5 MHz.

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.7-9
• /
• 2006

$(BaSr)TiO_3$ thick films were prepared by tape casting method using $BaTiO_3$ and $SrTiO_3$ powder slurry in order to investigate dielectric properties and low temperature sintering. Sintering density was $5.7\;g/cm^3$ and the BST sample exhibited the maximum dielectric constant, tunability at temperatures near phase transition point. The dielectric constant was increased and curie temperature was shifted to higher temperature with increasing of annealing temperature.